R3204P16-HP Load Balancing Module Network Management Configuration Guide-6PW101
Table Of Contents
- Title page
- Contents
- Interface management configuration
- IP addressing configuration
- MAC address table configuration
- Layer 2 forwarding configuration
- Layer 2 forwarding overview
- Configuring general Layer 2 forwarding
- Configuring inline Layer 2 forwarding
- Configuring inter-VLAN Layer 2 forwarding
- Forward-type inline Layer 2 forwarding configuration example
- Blackhole-type inline Layer 2 forwarding configuration example
- Inter-VLAN Layer 2 forwarding configuration example
- VLAN configuration
- ARP configuration
- Gratuitous ARP configuration
- Proxy ARP configuration
- Layer 3 forwarding configuration
- NAT configuration
- Overview
- Configuring a NAT policy in the web interface
- Configuring NAT in the CLIs
- Configuration guidelines
- ALG configuration
- Static route configuration
- RIP configuration
- OSPF configuration
- BGP configuration
- Policy-based routing configuration
- Route displaying
- DNS configuration
- Overview
- Configuring DNS on the web interface
- Configuring DNS in the CLIs
- Troubleshooting IPv4 DNS configuration
- Support and other resources
- Index
iii
Displaying and maintaining Layer 3 subinterface forwarding ········································································· 74
Configuring inter-VLAN Layer 3 forwarding ··············································································································· 74
Configuring inter-VLAN Layer 3 forwarding ······································································································ 74
Displaying and maintaining inter-VLAN Layer 3 forwarding ··········································································· 76
Layer 3 subinterface forwarding configuration example ··························································································· 76
Inter-VLAN Layer 3 forwarding configuration example ····························································································· 78
NAT configuration ····················································································································································· 80
Overview ········································································································································································· 80
Introduction to NAT ··············································································································································· 80
NAT implementation ············································································································································· 81
Low-priority address pool ····································································································································· 83
Configuring a NAT policy in the web interface ········································································································· 84
Configuration overview ········································································································································ 84
Creating an address pool ···································································································································· 85
Configuring dynamic NAT ··································································································································· 87
Creating a static address mapping ····················································································································· 88
Enabling static NAT on an interface ··················································································································· 89
Creating an internal server ··································································································································· 89
Configuring a DNS mapping ······························································································································· 91
NAT configuration examples ······························································································································· 92
Configuring NAT in the CLIs ········································································································································· 97
NAT configuration task list ··································································································································· 97
Configuring NAT address pool ··························································································································· 98
Configuring address translation··························································································································· 98
Configuring an internal server ··························································································································· 101
NAT configuration examples ····························································································································· 102
Troubleshooting NAT ·········································································································································· 106
Configuration guidelines ············································································································································· 106
ALG configuration ··················································································································································· 107
ALG overview ······························································································································································· 107
Enabling ALG ······························································································································································· 109
ALG configuration examples ······································································································································ 109
FTP ALG configuration example ························································································································ 109
SIP/H.323 ALG configuration example ··········································································································· 110
NBT ALG configuration example ······················································································································· 111
Static route configuration ········································································································································ 112
Configuring static route in the web interface ············································································································ 112
Static route configuration example ···················································································································· 113
Configuring static route in the CLI ······························································································································ 115
Configuration prerequisites ································································································································ 115
Configuration procedure ···································································································································· 115
Displaying and maintaining static routes ·········································································································· 116
Static route configuration example ···················································································································· 116
RIP configuration ····················································································································································· 119
Configuration prerequisites ········································································································································· 119
Configuration overview ··············································································································································· 119
Configuring RIP globally·············································································································································· 119
Configuring interface RIP ············································································································································ 120
RIP configuration example ·········································································································································· 121
Configuration guidelines ············································································································································· 123
OSPF configuration ················································································································································· 124
Configuration prerequisites ········································································································································· 124