R3204P16-HP Load Balancing Module Network Management Configuration Guide-6PW101

ManualsBrandsHP ManualsComputer AccessoriesHP 7100/7200 IPsec dl Module

Table Of Contents

Title page
Contents
Interface management configuration
- Interface overview
  - Physical interfaces
  - Logical interfaces
- Managing interfaces in the web
- Managing interfaces at the CLI
IP addressing configuration
- IP addressing overview
- Configuring IP addresses
  - Assigning an IP address for an interface
  - IP addressing configuration example
    - Network requirements
    - Configuration procedure
- Displaying and maintaining IP addressing
MAC address table configuration
- Overview
- Configuring a MAC address table in the web
- Configuring the MAC address table at the CLI
Layer 2 forwarding configuration
- Layer 2 forwarding overview
- Configuring general Layer 2 forwarding
  - Configuration procedure
  - Displaying and maintaining general Layer 2 forwarding
- Configuring inline Layer 2 forwarding
  - Configuration procedure
  - Displaying and maintaining inline Layer 2 forwarding
- Configuring inter-VLAN Layer 2 forwarding
  - Configuration procedure
  - Displaying and maintaining inter-VLAN Layer 2 forwarding
- Forward-type inline Layer 2 forwarding configuration example
  - Network requirements
  - Configuration procedure
- Blackhole-type inline Layer 2 forwarding configuration example
  - Network requirements
  - Configuration Procedure
- Inter-VLAN Layer 2 forwarding configuration example
  - Network requirements
  - Configuration Procedure
VLAN configuration
- Introduction to VLAN
- Configuring a VLAN in the web
- Configuring a VLAN at the CLI
  - Configuring VLAN
  - Configuring isolate-user-VLAN
ARP configuration
- ARP overview
- Configuring ARP
- Displaying and maintaining ARP
- ARP configuration example
  - Network requirements
  - Configuration procedure
Gratuitous ARP configuration
- Introduction to gratuitous ARP
  - Enabling learning of gratuitous ARP packets
  - Configuring periodic sending of gratuitous ARP packets
- Configuring gratuitous ARP
Proxy ARP configuration
- Proxy ARP overview
  - Proxy ARP
  - Local proxy ARP
- Enabling proxy ARP
- Displaying and maintaining proxy ARP
- Proxy ARP configuration examples
Layer 3 forwarding configuration
- Layer 3 forwarding overview
  - Layer 3 subinterface forwarding
  - Inter-VLAN Layer 3 forwarding
- Configuring Layer 3 subinterface forwarding
  - Configuring Layer 3 subinterface forwarding
    - Configure the ports of the switch
    - Configure the LB module
  - Displaying and maintaining Layer 3 subinterface forwarding
- Configuring inter-VLAN Layer 3 forwarding
  - Configuring inter-VLAN Layer 3 forwarding
    - Configure the ports of the switch
    - Configure the LB module
  - Displaying and maintaining inter-VLAN Layer 3 forwarding
- Layer 3 subinterface forwarding configuration example
  - Network requirements
  - Configuration procedure
- Inter-VLAN Layer 3 forwarding configuration example
  - Network requirements
  - Configuration procedure
NAT configuration
- Overview
- Configuring a NAT policy in the web interface
- Configuring NAT in the CLIs
- Configuration guidelines
ALG configuration
- ALG overview
- Enabling ALG
- ALG configuration examples
Static route configuration
- Configuring static route in the web interface
  - Static route configuration example
- Configuring static route in the CLI
RIP configuration
- Configuration prerequisites
- Configuration overview
- Configuring RIP globally
- Configuring interface RIP
- RIP configuration example
- Configuration guidelines
OSPF configuration
- Configuration prerequisites
- Configuration overview
- Configuring OSPF globally
- Configuring OSPF areas
- Configuring OSPF interfaces
- Displaying OSPF interface information
- Displaying OSPF neighbor information
- OSPF configuration example
- Configuration guidelines
BGP configuration
- Configuration prerequisites
- Configuration overview
- Configuring BGP globally
- Configuring BGP peer
- Displaying BGP peer information
- BGP Configuration example
Policy-based routing configuration
- Configuring PBR
- Creating a policy
- Applying a policy
- Configuration guidelines
Route displaying
- Displaying routing information in the web interface
- Displaying routing information in the CLI
DNS configuration
- Overview
- Configuring DNS on the web interface
- Configuring DNS in the CLIs
- Troubleshooting IPv4 DNS configuration
  - Symptom
  - Solution
Support and other resources
- Contacting HP
  - Subscription service
- Related information
  - Documents
  - Websites
- Conventions
Index

# Associate the isolate-user-VLAN with the secondary VLANs.

[LB B-vlan4] quit

[LB B] isolate-user-vlan 6 secondary 3 to 4

• Verification

# Display the isolate-user-VLAN configuration on LB A.

[LB A] display isolate-user-vlan

Isolate-user-VLAN VLAN ID : 5

Secondary VLAN ID : 2-3

VLAN ID: 5

VLAN Type: static

Isolate-user-VLAN type : isolate-user-VLAN

Route Interface: not configured

Description: VLAN 0005

Name: VLAN 0005

Broadcast MAX-ratio: 100%

Tagged Ports: none

Untagged Ports:

XGE0/0.1 XGE0/0.2 XGE0/0.5

VLAN ID: 2

VLAN Type: static

Isolate-user-VLAN type : secondary

Route Interface: not configured

Description: VLAN 0002

Name: VLAN 0002

Broadcast MAX-ratio: 100%

Tagged Ports: none

Untagged Ports:

XGE0/0.2 XGE0/0.5

VLAN ID: 3

VLAN Type: static

Isolate-user-VLAN type : secondary

Route Interface: not configured

Description: VLAN 0003

Name: VLAN 0003

Broadcast MAX-ratio: 100%

Tagged Ports: none

Untagged Ports:

XGE0/0.1 XGE0/0.5