HP StorageWorks e1200-320 4Gb Fibre Channel Interface Card user and service guide *AD577-96004* AD577-96004 Part number: AD577-96004 First edition: May 2006
Legal and notice information © Copyright 2006 Hewlett-Packard Development Company, L.P. Hewlett-Packard Company makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
Contents About this guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Intended audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Related documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Document conventions and symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5 Visual manager user interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Visual manager access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Main menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Visual Manager menu structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . System statistics menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Event Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Runtime report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
European Union notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BSMI notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Japanese notice. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Korean notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Safety . . . . . . . . . . . .
About this guide This guide provides information about: • Installing the HP StorageWorks e1200-320 4Gb FC Interface Card • Configuring the HP StorageWorks e1200-320 4Gb FC Interface Card • Troubleshooting the HP StorageWorks e1200-320 4Gb FC Interface Card Intended audience This guide is intended for general users who need physical and functional knowledge of the HP StorageWorks e1200-320 4Gb FC Interface Card.
IMPORTANT: Provides clarifying information or specific instructions. NOTE: Provides additional information. TIP: Provides helpful hints and shortcuts. HP technical support Telephone numbers for worldwide technical support are listed on the HP support web site: http://www.hp.com/support/.
1 Introduction The HP StorageWorks e1200-320 4Gb FC Interface Card provides bi-directional connectivity between one Fibre Channel Switched Fabric (FC-SW) or Fibre Channel Arbitrated Loop (FC-AL), and two Narrow/Wide Fast/Ultra320 LVD/SE SCSI buses. Supported devices include: • Initiator Devices – Fibre Channel hosts • Target Devices – Tape drives Figure 1 shows the layout of the HP e1200-320 4Gb FC Interface Card.
Operation indicators The HP e1200-320 4Gb FC Interface Card has LED indicators for monitoring overall status as shown in Figure 2.
How the HP e1200-320 4Gb FC Interface Card works The interface card is a device that translates the Fibre Channel Protocol (FCP) to and from the SCSI Protocol—transparently transferring commands, data, and status information—so that both the Fibre Channel (FC) and SCSI devices and hosts can communicate with each other. Interconnection is provided between two SCSI buses and one Fibre Channel Arbitrated Loop or Switched Fabric, making use of Fibre Channel’s ability to encapsulate SCSI protocol packets.
External indicators • Fibre Channel link status and activity LEDs • SCSI bus activity LEDs • Ethernet link status and activity LEDs • Power/Fault LED • Beacon LED Operating environment • 0 to 50°C, 32 to 122°F • 5 to 80% relative humidity (non-condensing) Non-operating environment (i.e.
2 Installation, cabling, and setup This chapter describes installing, cabling, and setup for the HP e1200-320 4Gb Interface Card. NOTE: Read this chapter carefully and completely before working with the interface card. Installing the HP e1200-320 4Gb Interface Card Before you begin, clear a work surface near the library to unpack the interface card. Keep the card in the static-sensitive bag until you are ready to install it.
Removal and installation NOTE: To avoid damage to the library, ensure cards are installed in the correct option slots. If you are installing one card, place it in the middle slot next to the controller board. If you are installing two cards in a 10U library, place the second card in the center slot on the bottom level of the library. Before removing an existing card or installing a new card, do the following: 1.
4. Remove the cables from the robotics controller (see Figure 5). Figure 5 Removing cables from the robotics controller Removing an existing interface card If you are replacing a card that is already installed in the library, save the configuration settings using the FTP user interface: ftp -> login -> bin -> get *.cfg .cfg. See ”Using the FTP interface” on page 89. To remove the interface card: 1. From the back of the library, locate the card to be removed (see Figure 6). 2.
Installing a new card NOTE: To avoid damage to the library, make sure cards are installed in the correct slots. To install one card, place it in the top level middle slot as shown in Figure 7. To install two cards, place the second card in the bottom level middle slot as also shown in Figure 7. 1. Using a #1 Phillips screwdriver, remove the center option slot cover plate (see Figure 7). Figure 7 Option slots in a 10U library 2.
3. Using the #1 Phillips screwdriver, tighten the captive screws in both of the black ejector handles as shown in Figure 9.
4. Cable the library as shown in Figure 10 for a 5U library, or Figure 11 for a 10U library.
5. Connect each power cord. Turn on the master power switch for each power supply (see Figure 12). Figure 12 Power supply and power cord 6. Turn the library on by pressing the Power button on the GUI control panel (see Figure 3 on page 14).
Interfaces and connections There are four types of interfaces to the interface card: • Fibre Channel • SCSI • 3-pin serial port • Ethernet The 3-pin serial and Ethernet ports are used for configuration and management of the interface card. For convenience in configuring ports, key information is indicated on a label located on the face of the interface card such as WWN name, WWP name, and Ethernet MAC ID (Physical Address).
To connect the interface card to a SCSI bus: 1. Power off the SCSI devices on this bus. 2. Connect a SCSI cable to one of the SCSI connectors on the unit. The interface card should always be installed at the end of the SCSI bus. 3. Make sure that the bus is terminated correctly. By default, the interface card is automatically terminated. However, the device at the other end of bus must also be terminated. Ethernet connection A 10/100BaseT Ethernet connection provides management and configuration access.
Setting up serial port communications Before supplying power to the interface card, HP recommends setting up serial port communications with your host computer, unless serial I/O was previously established and is currently running. The interface card is designed to communicate with a terminal or any operating system utilizing a terminal emulator. For example, most Windows® operating systems can use a terminal. Be sure the baud rate, data bits, stop bits, parity, and flow control are set correctly.
3 Device management To provide connectivity between hosts and devices, it is necessary for the interface card to be recognized with an address on the connected Fibre Channel network. SCSI bus configuration The interface card provides the capability to reset SCSI buses during the interface card boot cycle. This allows the devices on a SCSI bus to be set to a known state. Configuration provides for the SCSI bus reset feature to be enabled or disabled.
Discovery Discovery is a feature that makes it easy to display attached FC and SCSI target devices and have them mapped automatically on the host side for the connected bus/port. There are two discovery methods available—Manual Discovery and Auto Discovery. Auto Discovery can be set to occur after either reboot events (when the card reboots) or link-up events (for instance, when cables are attached or a hub is rebooted).
The Auto Assigned map is built dynamically, and contains all the devices found during discovery. This map changes automatically any time the discovery process finds a change in the devices attached to the interface card. This map can be displayed, but cannot be modified directly by the user. The SCC map is only available on the FC port and contains a single entry. LUN 0 is an interface card LUN, and access to devices behind the controller is handled by using SCC logical unit addressing.
Device management
4 Interface card management The HP e1200-320 4Gb FC Interface Card can be managed over the following user interfaces: • Over the serial port via a terminal or a terminal emulation utility. • Over Ethernet via a Telnet utility or an HTTP-based interface called Visual Manager. Additionally, FTP support provides additional management functionality. Before attempting to configure the interface card, a basic understanding of Fibre Channel and SCSI devices is recommended.
to always provide the same IP address to the interface card. This setup can be useful for remote management of the interface card via Telnet. Because the method of setting up a lease reservation varies depending on the DHCP server being used, HP recommends that you contact your Network Administrator for assistance. For more information about enabling DHCP on the interface card, see ”Enabling DHCP on the HP e1200-320 4Gb FC Interface Card” on page 117.
Other than dynamic mapping changes, any other changes will not take effect until the next time the interface card reboots. You can force the interface card to reboot by selecting the Reboot option. For more information about the Visual Manager interface, refer to ”Visual manager access” on page 31. NOTE: For the VM interface’s dynamic display of the interface card configuration to be presented properly, use version 6.2 or later of Netscape’s browser on non-Solaris platforms, or Netscape version 6.2.
Interface card management
5 Visual manager user interface The HP e1200-320 4Gb FC Interface Card allows any standard Internet Web browser to view and change the interface card’s configuration with the Visual Manager interface. Information is dynamically generated in an HTML format by the interface card so that Web browsers can access it. To access Visual Manager, enter the IP address of the interface card into the address field of a Web browser.
5. Enter the authorized user name and password. The user name and password are case-sensitive. The default user name is root and the default password is password. Figure 13 Password dialog box NOTE: HP recommends changing the user name and password from the defaults. NOTE: To end the current session of VM, the browser window must be closed. Navigating the browser to another URL does not end the current session.
Home page The Main menu home page is displayed when Visual Manager (VM) is accessed. The home page contains status information, including a physical image of the interface card (see Figure 15). Figure 15 Visual Manager Home page Home page information includes: • The HP logo is located in the upper left corner of the Home page (see Figure 15). If the Internet is accessible to the host, click the HP logo to open the web site. • An illustration of the interface card is located near the top of the home page.
• Main menu options: • Home displays interface card status information. • System configures standard system components. • Ports configures the Fibre Channel port and SCSI buses. • Discovery displays devices and discovers new devices. • Mapping displays and configures maps. • Statistics displays interface card statistics. • Utilities configures utility settings. • Report displays system information. • Reboot restarts the interface card.
Serial configuration The Serial screen is used to change the baud rate for the serial port (see Figure 18). NOTE: If the Autobaud feature is being used, it may not be necessary to set the baud rate. Figure 18 Serial screen The current baud-rate setting is displayed. Baud rate choices are: • 9600 • 19200 • 38400 • 57600 • 115200 NOTE: HP recommends setting the baud rate to 115200.
Network configuration The Network screen is used to enter Ethernet configuration settings (see Figure 19). Figure 19 Network screen CAUTION: If this configuration is incorrectly set, processing difficulties may occur. Before changing this setting, evaluate the need for the change and verify the desired setting. HP recommends backing up the interface card configuration to an external file before making changes to this setting.
NOTE: To use the DHCP feature, a DHCP server must be operational on the Ethernet network. If the DHCP feature is used when there is not DHCP server, the standard for DHCP requires the interface card wait three minutes for a response from a DHCP server before timing out. Some DHCP servers allow an extended lease reservation to be set up for an IP address by providing the server with the Ethernet MAC address. The DHCP server always provides the same IP address to the interface card.
User The User screen is used to set up interface card security (see Figure 21). Figure 21 User screen: security settings User settings: • User Name (default: root) is any alphanumeric combination. Passwords must be 8 to 11 characters in length. • Password (default: password) is any alphanumeric combination. • Confirm Password The user name and password should be unique and kept confidential. HP recommends using a combination of letters and numbers when creating the user name and password.
Real-Time Clock configuration The Real-Time Clock screen is used to set the system time and date (see Figure 22). Figure 22 Real-Time Clock screen Date/time settings: • Date Settings sets the month, day, and year (use a four-digit number to represent the year) • Day of Week sets the day of the week. • Time Settings sets the hours, minutes, and seconds. The system clock is a 24-hour clock. There is no a.m. or p.m. designation. Example 1:00 p.m. is 13 hours, 00 minutes.
Reset menu The Reset menu is used to reset the interface card to factory default settings (see Figure 23). Figure 23 Reset to Factory Default screen Current interface card activities are disrupted while the unit resets the configuration to the factory defaults and saves those options to FLASH memory. CAUTION: changes. Resetting the interface card configuration to the factory defaults deletes custom maps or map NOTE: Resetting to factory defaults through VM does not affect Ethernet connectivity.
Ports menu Accessed from the Main menu, the Ports menu is used to view and to modify configuration settings of the Fibre Channel port and SCSI buses (see Figure 24). Figure 24 Ports menu The initial screen display of the Ports menu includes summary information about each Fibre Channel port and SCSI bus in the interface card. Ports menu tasks: • Fibre Channel Port 0 configuration changes the Fibre Channel port settings. • SCSI Bus 0, 1 configuration changes SCSI bus settings.
Fibre Channel port configuration When the Fibre Channel port is selected in Ports menu, the Fibre Channel Configuration screen is displayed (see Figure 25). Figure 25 Fibre Channel port 0 configuration settings screen Fibre Channel port settings: • Link Status indicates the port link status. • Port Mode (default: N_Port) sets the port mode. Port Mode settings: • Auto Sense: In this mode, the Fibre Channel port tries to negotiate as a loop.
• Both the ports and the devices behind the ports are discovered for the first link-up event. Subsequent link-up events only discover the ports and not the devices behind the ports. • Manual Discovery Only (default) sets discovery of new devices to occur only after the user selects the Discovery option from the Main menu or when a Registered State Change Notification (RSCN) is received from a fabric. • Buffered Tape Writes (default: enabled) enables or disables the Buffered Tape Write option.
SCSI bus configuration settings: • Primary Initiator ID (default: 7) must be a unique ID. • Discovery toggles between Enabled and Disabled, Enabled by default. • Bus Reset on Boot toggles between Enabled and Disabled. When enabled, the interface card automatically resets SCSI buses during a power-up or reboot of the library. • Discovery Delay is the wait time after a power-up or reboot before discovering SCSI devices.
2. Select Go.
Mapping menu Accessed from the Main menu, the Mapping menu is used to create or edit LUN maps and assign them to hosts. (see Figure 30). Figure 30 Fibre Channel port 0 map settings NOTE: Indexed, Auto Assigned, and SCC maps cannot be deleted or renamed. NOTE: SCC and Auto-Assigned maps cannot be cloned.
Viewing and changing Fibre Channel map information NOTE: Port 0 Device Map is the HP recommended map to be used for editing and assigning oncoming hosts. The Indexed (default) map should not be used for editing, even though the user is able to edit this map. To view or change current Fibre Channel map information: 1. In the Mapping menu screen, select the desired map. 2. Select Edit/View in the Map section of the screen. The Fibre Channel Map dialog box is displayed.
Statistics menu Accessed from the Main menu, the Statistics menu is used to display Fibre Channel port and SCSI bus information (see Figure 31). Figure 31 Statistics menu To view information for a specific port or bus, click the component on the menu bar or the interface card image. To refresh the display, select Reset FC & SCSI System Statistics.
Utilities menu Accessed from the Main menu, the Utilities menu is used to view and configure utility options (see Figure 32). Figure 32 Utilities menu Utilities menu tasks: • FTP Utility opens an FTP session. • Trace Settings configures trace settings. • Current Traces displays current trace information. • Previous Traces displays previous trace information. • Last Assert Traces displays last assert trace information. • Clear Current Traces clears current trace information.
FTP utility access The FTP utility screen is used to open an FTP session (see Figure 33). Figure 33 FTP Utility screen The FTP utility requires the use of a JAVA applet and prompts for permission to install the applet, if needed. If the prompt is displayed, follow the on screen instructions to complete the installation. The FTP utility then prompts for permission to run the applet.
NOTE: If a valid firmware or configuration file is uploaded to the interface card, an automatic reboot occurs once the file has been received. The interface card cannot be accessed from the Visual Manager UI during the time that the reboot is in process, which is approximately 30 seconds. Trace settings configuration This menu allows the configuration of Trace Settings (see Figure 34).
Table 6 Trace Settings Setting Description INBAND Controller management functionality is monitored and recorded Queue Element Debugging capability for specific interface card resources Current, previous, and last assert trace displays These three Utilities menu screens show trace information. • The Current Traces screen shows data since the interface card was last booted. • The Previous Traces screen shows data from the last boot cycle.
• Warning Events • Notify Events • Info Events • Debug Events • Log All Events Event logging captures the last 215 events and then starts overwriting the log. NOTE: To correlate event logging, correctly set the clock and date in the Real-Time Clock configuration menu. Event log display The Event Log screen is used to view the Event Log (see Figure 36).
Clear event log The Clear Event Log screen is used to clear the Event Log (see Figure 37). Current interface card activities are not disrupted. Figure 37 Clear event log screen SCSI command tracking This menu provides options for setting up and logging SCSI commands that are received or transmitted by the interface card. Results are displayed in the Host/Device ID Table (see Figure 38).
While the interface card’s current, previous, and last assert trace data does provide a complete summary of events in a chronological fashion, SCSI Command Tracking adds the ability to filter the trace data to show only the information related to the processing of specific SCSI commands. • SCSI Command Tracking can be toggled to ON or OFF. When toggled ON and submitted, all SCSI commands received or transmitted to or from the interface card are then logged in the SCSI Commands section shown on this screen.
Reboot option CAUTION: Confirm there is no activity, such as a backup in progress, before initiating a reboot because interface card activities will be disrupted. Interface card reboots are executed using this Main menu option (see Figure 39). When the library is rebooted, current interface card activities are disrupted. All submitted configuration changes are activated during the boot-up process. Figure 39 Reboot screen The system automatically returns to the home page after the reboot has completed.
6 Using the Command Line Interface This chapter describes specific configuration options available from the perspective of the Command Line Interface (CLI). For an overview of using the other configuration methods available, see ”Interface card management” on page 27. The interface card allows the user to access many configuration settings through the Command Line Interface.
• Select 1 to access interface card configuration settings. • Select 2 to access System Utilities. • Select 3 to display trace and assertion history. • Select 4 to reboot the interface card. A confirmation message appears to verify this action. • Enter N to return to the System Utilities menu. • Enter Y to restart the interface card. • Select 5 to download a new revision of the firmware. A confirmation message appears to verify this action.
Baud rate configuration This menu changes the baud rate used on the serial port. Select 1 through 5 for the appropriate baud rate setting. If you are using the Autobaud feature, it may not be necessary to set a baud rate. See ”Autobaud feature” on page 21 for more information on using the Autobaud feature. The default setting for the baud rate is 115200. Figure 42 Baud rate configuration menu Baud Rate Configuration Menu X.XX.
Ethernet configuration This option allows for setting up all Ethernet network settings including IP address, subnet mask, IP gateway, security settings, Ethernet mode, physical address, and host name. Figure 43 Ethernet configuration menu Ethernet Configuration Menu X.XX.XX XXXXXX 07/7/2005 XXXXXXXXXXXXXXXX 08:56:22 IP Address : 192.168.60.203 [DHCP] Subnet Mask : 255.255.255.0 IP Gateway : 192.168.60.
• Select 7 to toggle the DHCP setting. This setting enables/disables support for Dynamic Configuration Protocol. The default setting is enabled. When enabled, the interface card retrieves a dynamic IP address from a DHCP server located on the Ethernet network that the interface card is connected to. If DHCP is disabled and then enabled, it is necessary to save the current configuration and reboot the interface card before an IP address can be requested from the DHCP server. Use the following four steps: a.
Fibre Channel configuration This menu allows for setting the Fibre Channel Address method, Hard Address value, discovery mode, WWN overrides, tape backup settings, default map value, and FC port mode. Figure 44 Fibre Channel configuration menu Fibre Channel Configuration Menu X.XX.
• Select 3 to change the Toggle Port Mode between Auto Sense - Soft AL_PA, N_Port, and Auto Sense Hard AL_PA. The default setting is N_Port mode. In this mode, the FC port tries coming up as a fabric port. If the interface card is on a loop and N_Port mode is selected, an error in communication may occur. In Autosense - Soft AL_PA mode, the interface card FC port tries to come up as a loop, and if not successful, then tries to come up as a fabric.
Following are descriptions for each of the override settings: NOTE: Normally, override settings should not be changed except when directed to do so by an authorized HP technician. • Select 1 to toggle the Hi-Sup Bit between SET and CLEAR. The default setting is CLEAR. This option should be toggled to SET when the server uses the Hi-Sup bit to scan for FC LUNs greater than eight. NOTE: Hi-Sup Bit is only set in an Active Fabric LUN which needs to be mapped as the first device (FC LUN 00).
Parallel SCSI configuration This menu allows for setting up SCSI attributes. Figure 45 Parallel SCSI configuration menu Parallel SCSI Configuration Menu X.XX.
SCSI initiator menu This option allows for setting up the SCSI Initiator. Figure 46 SCSI initiator menu SCSI Initiator Menu X.XX.XX XXXXXX 07/7/2005 XXXXXXXXXXXXXXXX 08:56:22 Current Initiator Configuration - Bus 0 Initiator ID : 07 1) Select primary SCSI Initiator ID 2) Enable/Disable alternate SCSI ID (The "alternate" ID is used to enhance the performance of status ("agent") commands that are being issued to a serial device.
Maximum SCSI bus speed menu This option allows for setting the maximum SCSI bus speed. When this option is selected, the user must first select the Target ID for the bus before this menu appears. Figure 47 SCSI bus speed configuration menu SCSI Bus Speed Configuration Menu X.XX.
Device mapping This option allows the user to manipulate maps and associate selected host with a particular map. Each physical port/bus on the system has at least an Indexed map and Auto Assigned map. In addition, there is a SCC Map and a Port 0 Device Map on FCP ports. Each map has a unique name and map ID. You can rename all maps, except for Indexed, Auto Assigned, and SCC.
NOTE: Because the entire list of maps may not fit on one screen, select N or P to go back and forth between screens displaying more maps. Select X to return to the Device Mapping Main menu. • Select 3 from the Device Mapping Main menu to create a new map. This option allows adding a new map for the current protocol/port or bus. Once the map is created, it becomes the current map. • Select 4 from the Device Mapping Main Menu to delete current map. The screen asks for confirmation before deleting the map.
NOTE: Hi-Sup Bit is only set in an Active Fabric LUN which needs to be mapped as the first device (FC LUN 00). Select a number from the left column Num to add a device to the map. Selecting a device where LUN=’-’ adds all LUNS for this target. If the selected device is already mapped, an error message appears to warn the user about adding a duplicate device. N and P controls allow scrolling up and down the device list. X brings the user back to the Edit Map Entries display table.
Remove gaps NOTE: SCSI devices attached to a Fibre Channel port must be mapped as sequential FC LUNs starting at LUN number 00. Skipping LUN numbers is not recommended when mapping FC LUNs because FC Discovery stops the discovery process whenever an empty LUN position is found. This option removes any incremental gaps in the sequence of LUNs listed in the table. Deleting an entry The user selects a LUN ID.
The following is an example of a host list for FCP hosts: Figure 52 Host list for FCP hosts Host List Edit Display X.XX.
Following the successful addition of the host, the host list is displayed again and the user can make sure that the host information is correct. Deleting a host Select D to delete a host from the host list. The operator is asked to enter an index for the host that is displayed in the very left column of the table, and asked for confirmation. Editing a host Select E to edit host information.
• Select 8 from the Device Mapping Main menu to display the entire device list. Because the entire device list may not fit on one screen, select N or P to go back and forth between screens displaying more maps. Select X to return to the Device Mapping Main menu. Figure 55 Entire device list Entire Device List X.XX.
Trace and event settings configuration This option allows set up of trace and events settings. Figure 56 Utility settings Utility Settings X.XX.XX XXXXXX XXXXXXXXXXXXXXXX 07/7/2005 08:56:22 1) Trace Settings Configuration 2) Event Settings Configuration 3) Special Event Logging Configuration X) Return to previous menu • Select 1 to edit the trace settings configuration. • Select 2 to edit the event settings configuration. • Select 3 to edit the special event logging configuration.
If the Enter key is selected, the next page of trace levels appears as follows: Figure 58 Trace settings Trace Settings X.XX.XX XXXXXX 07/7/2005 0) SG List : OFF 1) Timing : OFF 2) FCP/RMI : OFF 3) AF : OFF 4) INBAND : OFF 5) Multi-Host Lib : OFF 6) Queue Element : OFF XXXXXXXXXXXXXXXX 08:56:22 U) Update Current Operating Trace Levels X) Return to previous menu Enter the trace level index, for next page > Enter a level number from the Trace Settings that are shown.
• Enter 1 to disable event logging. • Enter 2 through 9 to log the specified events or higher. • Enter 0 to log all events. • Select U to send event configuration changes to the interface card now. NOTE: Event logging captures over 2000 events and then starts overwriting the log when full. NOTE: Be sure to correctly set the clock and date in the Real-Time Clock Configuration menu so that event logging is accurate.
Real-Time clock configuration When this option is selected from the Perform Configuration menu, the System Clock Setup menu appears. NOTE: The time is based on a 24-hour clock. There is no a.m. or p.m. designation. For example: 1:00 p.m. is 13 hours 00 minutes or 13:00. Figure 61 System clock setup menu - System Clock Setup Menu X.XX.XX XXXXXX XXXXXXXXXXXXXXXX 07/7/2005 08:56:22 TUESDAY, Date: 07/7/2005, Time: 08:56:22 1) Set clock X) Return to previous menu Select 1 to set the clock.
• Select 1 to change the number of interface card LUNs reported by the interface card. This value can be set to a number in the range of 0 to 4. • Select 2 to change the location of LUNs in an auto-assigned map. LUNs can be positioned starting at the beginning (first location) or at the end (last location) of the map. For more information on interface card LUNs, see ”Inband SCSI-3 commands” on page 109.
System statistics menu Figure 64 System status/statistics menu System Status/Statistics menu X.XX.XX XXXXXX 07/7/2005 XXXXXXXXXXXXXXXX 08:56:22 1) Display System Status 2) Display Fibre Channel Protocol Status 3) Display Parallel SCSI Protocol Status X) Return to main menu • Select 1 from the System Status/Statistics menu to display system status. Figure 65 System status menu System Status Menu X.XX.
• Select 1 from the Fibre Channel Status menu to display Fibre Channel Link Status. Figure 66 below shows the status and statistics for a Fibre Channel loop. Similar data can also be shown for a Fibre Channel fabric. Figure 66 Fibre Channel status & statistics Fibre Channel Status & Statistics X.XX.
Table 7 Fibre Channel status SyncLosses is the number of times loss of sync. was detected. BadRxChars is the number of bad characters received. LinkFailures is the number of link failure conditions. BadCRCFrames is the number of frames received with a bad CRC. ProtocolErrs is the number of protocol errors detected. BadSCSIFrames is the number of bad SCSI frames detected. UnderflowErrs is the number of underflow errors detected. Select A to have the status information repeatedly refreshed.
• Select 5 to display FC SeqCmd_Q Resources. • Select 6 to display FC SFP Data. • Select 3 from the System Status/Statistics menu to display Parallel SCSI Protocol Status. Figure 68 Parallel SCSI protocol status menu Parallel SCSI Protocol Status menu X.XX.XX XXXXXX XXXXXXXXXXXXXXXX 07/7/2005 08:56:22 1) Display SCSI Statistics 2) Display Attached SCSI Devices 3) Display SCSI Resource Status X) Return to previous menu • Select 1 to display SCSI statistics. • Select 2 to display attached SCSI devices.
Event Log When this option is selected from the System Utilities menu, the Event Log menu is displayed. Figure 70 Event log menu Event Log Menu X.XX.XX XXXXXX XXXXXXXXXXXXXXXX 07/7/2005 08:56:22 1) Display event log 2) Clear event log X) Return to previous menu • Select 1 to display the event log. • Select 2 to clear the event log of all old entries and start over with an empty list.
Diagnostics mode When this option is selected from the System Utilities menu, a confirmation message appears to verify the selection. If a response of Y (yes) is given to the confirmation message, current interface card activities are interrupted while the unit restarts itself and enters diagnostics mode. The power-up messages appear followed by the diagnostics menu. Figure 72 System diagnostics mode System Diagnostics Mode X.XX.
Special FC link control When this option is selected from the System Utilities menu, the Special Fibre Channel Link Control menu is displayed. Figure 73 Special FC Link states menu Special FC Link Control X.XX.
or other ID. SCSI commands which have already been tracked, then that information is displayed by selecting this option. • Select 4 to clear the log of all previously recorded results. Display trace and assertion history When this option is selected from the main menu, the Trace Dump menu is displayed. Trace options are set up in the Trace Settings Configuration menu. Figure 75 Trace dump menu Trace Dump Menu X.XX.
• For the previous trace buffer, use get prvtrace.txt. The file transfers from the interface card. Reboot When this option is selected, a confirmation message appears to verify the selection. If a response of Y (yes) is given to the confirmation message, current interface card activities are disrupted while the unit restarts itself. The last saved configuration changes also take effect after the interface card powers on again.
7 Using the FTP interface This chapter describes specific management options available from the FTP interface. For an overview of using the other management interfaces available, see ”Interface card management” on page 27. Backup/restore configuration settings The interface card supports backup and restore of configuration settings over FTP. This allows users to maintain multiple setting configurations externally from the interface card and to be able to restore any of the configurations as needed.
NOTE: If the interface card is to use a static IP address, the pre-filled in address when DHCP is disabled is 1.1.1.1 and should be changed to an address that is appropriate for the IP network it will reside on. 3. Enter the user name and password. The default values for user name and password are root for the user name and password for the password. 4. Specify binary mode: bin 5. Specify the configuration’s path and filename (.cfg file) with the put command: put
The file will transfer to the current directory specified on your computer’s FTP utility. If running FTP from a DOS or Linux command line, the destination directory can be set using the lcd command (ex. lcd c:\myCfg). Updating firmware Using the following procedure, FTP can be used to update the interface card firmware. 1. Connect the interface card to the Ethernet network used by your computer. 2.
Using the FTP interface
8 Troubleshooting Various problems can arise when configuring and using the HP e1200-320 4Gb Interface Card. This section is provided to help guide the user through some of the basic methods of identifying faults in the setup and configuration of the unit. Most problems are found in the initial installation. In general, it is wise to check all connections and review the configuration before proceeding with further trouble analysis.
• Ethernet (10/100)—When lit, these green indicators signify Ethernet link status and activity. If either of these indicators fail to flicker, or stay continuously lit, there may be a problem with the network connection or configuration. Verify the network connection and configuration. The port must be connected to a Ethernet network to function properly.
3. Select the Wizard’s Search for Better Driver option and specify the folder containing the interface card INF file. The Hardware Wizard will scan the specified folder for all INF files and will select the first INF file it finds with a device entry containing a matching hardware ID string. NOTE: The Hardware Wizard will copy the selected INF file, renaming it to OEM<#>.inf, where the # is some integer, and it will place the copied file into the C:\WINNT\inf folder.
If devices are listed, verify FC HBA mapping mode or AL_PA addresses on the interface card. Verify configuration A number of configuration changes may result in an invalid configuration. If you are in doubt about the configuration, restore the interface card to the factory default configuration and proceed to configure the unit a step at a time, verifying the functionality of the configuration as changes are made. Verify mapping Verify that all desired devices have been discovered and mapped.
Read XFER_RDY Disabled 0x1 Write XFER_RDY Disabled 0x0 Verify HBA device driver information Check the HBA device driver Readme.txt file for configuration specifics. An HBA may require a different configuration, depending on whether it is connected to a loop or a switch. HBAs typically come with utility programs to view or change their configurations. Running diagnostics You can run a diagnostics wrap test from Diagnostics Mode in the serial interface.
Troubleshooting
A Serial and Ethernet pin assignments RJ-11 pin assignments The pin assignments given for the 3-pin serial connection are in reference to the serial receptacle on the rear panel of the HP e1200-320 4Gb FC Interface Card. Use an RS-232 null modem cable to connect the HP e1200-320 4Gb FC Interface Card to the host system.
DB-9 pin assignments In conjunction with the pin assignments provided for the 3-pin receptacle on the rear panel of the HP e1200-320 4Gb Interface Card, following are the corresponding pin out assignments for a DB-9 serial connector used to connect the other end of the serial cable to a terminal, or a computer running terminal emulation software. The pin assignments given in Figure 78 for the DB-9 serial connection are in reference to the serial connector at the end of the cable.
RJ-45 Ethernet Pin Assignments The pin assignments given for the RJ-45 Ethernet connection are in reference to the Ethernet receptacle on the back panel of the HP e1200-320 4Gb Interface Card. The HP e1200-320 4Gb Interface Card Ethernet connection supports the IEEE specifications for 10BASE-T and 100BASE-TX Ethernet standards.
Serial and Ethernet pin assignments
B Regulatory compliance and safety Regulatory compliance Federal Communications Commission notice Part 15 of the Federal Communications Commission (FCC) Rules and Regulations has established Radio Frequency (RF) emission limits to provide an interference-free radio frequency spectrum. Many electronic devices, including computers, generate RF energy incidental to their intended function and are, therefore, covered by these rules.
Declaration of conformity for products marked with the FCC logo, United States only This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. For questions regarding your product, visit http://www.hp.com.
International notices and statements Canadian notice (avis Canadien) Class A equipment This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. Class B equipment This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Japanese notice Korean notices Safety Battery statement WARNING! This product contains one lithium manganese dioxide battery. • The e1200-320 4Gb Fibre Channel Interface Card contains one Snaphat® lithium battery. • The lithium battery is located in the upper left corner of the board, is yellow in color, and can be removed with a flat blade screwdriver. Lithium may be considered a hazardous material. Dispose of these batteries in accordance with local, state, and federal laws.
Taiwan battery recycling notice The Taiwan EPA requires dry battery manufacturing or importing firms in accordance with Article 15 of the Waste Disposal Act to indicate the recovery marks on the batteries used in sales, giveaway or promotion. Contact a qualified Taiwanese recycler for proper battery disposal.
Regulatory compliance and safety
C Inband SCSI-3 commands The HP e1200-320 4Gb Interface Card supports a set of SCSI-3 commands that can be received inband over iSCSI/NDMP. When received by the interface card, these commands are then executed by the interface card itself. When using SCSI-3 commands to access general management features, the commands can be sent to device LUNs that are mapped through the interface card. The following is a list of the SCSI-3 commands that are supported by the interface card.
The interface card returns the LUN Parameters as defined in Table 13. Table 13 Report LUNs Parameter List Bit 7 6 5 4 3 2 1 0 Byte 0 (MSB) 1 LUN list length 2 3 (LSB) 4 Reserved 5 Reserved 6 Reserved 7 Reserved LUN list 0-7 First LUN : 0-7 Last LUN NOTE: The LUN list length is the number of LUNs times 8. All LUNs are reported and will appear in the host’s map. Inquiry command The format of the Inquiry command is shown in Table 14.
EVPD Page 0x80 If the EVPD bit is set and the Page Code is 0x80 the unit serial number page is returned. The format of this page is shown in Table 15. Table 15 Format of EVPD Page 0x80 Bit 7 6 5 4 3 2 1 0 Byte 0 Device Type (0ch) 1 Page Code (80h) 3 Reserved 4 Page Length 5...20 Serial Number The serial number field is a 16-byte left-justified ASCII string.
NOTE: The Revision Level comes from the last four characters of the build string, which appears in the headings for most menu screens.
D Addressing, structures, and operations Fibre Channel and SCSI systems employ different methods of addressing devices. The inclusion of a interface card requires that a method of translating device IDs be implemented so that each SCSI device is mapped to the appropriate Fibre Channel LUN. The SCSI buses establish bus connections between devices. Targets on a SCSI bus may internally address logical units. The addressing of a specific SCSI device is represented by the BUS:TARGET:LUN triplet.
The interface card supports the Peripheral Device Addressing Method and the Logical Unit Addressing Method, depending on the configuration.
Indexed addressing option Indexed Addressing allows for host bus adapter (HBA) drivers that only use Peripheral Device addressing to access SCSI devices attached to the interface card. This is done by use of a table, which is indexed by sequential LUN values, indicating selected BUS:TARGET:LUN devices. It is not possible in this mode to address the interface card as an interface card unit directly. The table has the structure as shown in Table 22.
attached devices. The host can then perform actions on these interface card attached devices directly without having to perform discovery by issuing commands through all possible combinations.
E Enabling DHCP on the HP e1200-320 4Gb FC Interface Card DHCP, or Dynamic Host Configuration Protocol, is an open industry standard that simplifies administering networks based on Transmission Control Protocol/Internet Protocol (TCP/IP). DHCP allows network resources to go farther by enabling a unique IP address to be assigned to a specific device (interface card, client host, etc.) on a non-permanent, dynamic basis. DHCP makes network administration easier—the larger the network, the greater the benefit.
Setting up DHCP over interface card interfaces Interface cards use three different interfaces which can be used to enable DHCP: Serial, Telnet, and VM. The following will describe how to enable and disable DHCP for each interface. NOTE: Located on the interface card is a label that displays the unit’s Ethernet MAC Address. A network administrator can then use this MAC Address to set up a lease reservation on the DHCP server for the IP address of the interface card.
• Select 2. The following menu appears: Figure 82 Ethernet configuration menu Ethernet Configuration Menu X.X.XX XXXXXX XXXXXX-XXX_XXXXXXXXXXXXXX 07/7/2005 08:56:22 IP Address : 1.1.1.1 Subnet Mask : 255.255.255.0 IP Gateway : 0.0.0.
NOTE: To use the DHCP feature, a DHCP server must be operational on the Ethernet network used by the interface card. If the DHCP feature is used when there is no DHCP server, the standard for DHCP requires that the interface card wait three minutes for a response from a DHCP server before timing out. During this period, the interface card menus and functions will not be accessible.
Visual Manager To access the interface card using the Visual Manager interface: 1. Look up the current IP address within the Ethernet Configuration menu using the serial interface. 2. Type the IP address in the Web browser without using “www” or “/” or any other characters or symbols. 3. After entering the IP address, the user should see the Configuration Main menu. Click on the Configuration link. This will access the Configuration Menu containing CURRENT/NEW readings for DHCP (“Use DHCP”).
Enabling DHCP on the HP e1200-320 4Gb FC Interface Card
Glossary adapter A printed circuit assembly that translates data between the FC host processor’s internal bus and a different bus, such as SCSI. address See SCSI addressing. addressing mode Used to create a mapping table that maps devices on the SCSI bus to Fibre Channel logical units. AL_PA Arbitrated Loop Physical Address. A unique one-byte valid value, derived and used in an Arbitrated Loop Topology as defined in ANSI specification FC_AL ver 4.5.
FC-AL See Fibre Channel - Arbitrated Loop. FC adapter A printed circuit assembly that translates data between the FC host processor’s internal bus and the FC link. This is also known as an HBA, or Host Bus Adapter. FC device A device that uses Fibre Channel communications. FC port An opening at the back of the interface card that provides a fiber optic connection between the FC adapter and the FC host.
indexed addressing A menu name. It allows for generic Fibre Channel host bus adapters to access SCSI devices attached to the interface card using a table which is indexed by sequential LUN values. initiator A device (usually a host system) that requests an operation to be performed by another device known as a target (usually a peripheral). initiator mode Configuration mode of the interface card in which a Fibre Channel initiator requests operations to be performed by a SCSI target device.
offline Taking the interface card offline indicates that all SCSI and FC adapters in the interface card are offline. Taking a SCSI adapter offline means ending inputs/outputs and suspending all transactions going from the interface card to the specified SCSI devices. The SCSI adapter is no longer active or available for access. Taking a FC adapter offline means ending inputs/outputs and suspending all transactions going from the interface card to the specified FC device.
SCSI addressing A SCSI adapter supports up to 16 devices, including itself. Each device has its own unique SCSI address. The SCSI address of a device dictates the device’s priority when arbitrating for the SCSI bus. SCSI address “7” has the highest priority. The next highest priority address is “6” followed by 5, 4, 3, 2, 1, 0, 15, 14, 13, 12, 11, 10, 9, 8, with “8” being the lowest priority address. The narrow SCSI adapter is factory set to address 7.
view port name A status type in the FC Status Menu showing the identification of the port. world wide name (WWN) A Name_Identifier which is worldwide unique, and represented by a 64-bit unsigned binary value.
Index A addressing 113 audience 7 authorized reseller, HP 8 autobaud 21 Avis Canadien, regulatory compliance notice 105 power-up messages 57 conventions document 7 text symbols 7 current map, default Fibre Channel Visual Manager 43 B D batteries Taiwan EPA recycling and disposal 107 baud rate configuration Visual Manager 35 BSMI, regulatory compliance notice 105 buffered tape writes Fibre Channel Visual Manager 43 bus reset on boot Visual Manager 44 C cables FCC compliance statement 104 shielded 104 Ca
Class B Equipment, compliance notice 103 declaration of conformity 104 modifications 104 Fibre Channel hosts viewing and changing Visual Manager 47 Fibre Channel maps editing entries Visual Manager 47 viewing and changing Visual Manager 47 Fibre Channel port buffered tape writes Visual Manager 43 configuration Visual Manager 42 Configuration screen, illustrated 42 default map Visual Manager 43 discovery mode Visual Manager 42 performance mode Visual Manager 43 port mode Visual Manager 42 firmware download 8
R rack stability, warning 8 reboot 88 rebooting Visual Manager 56 recycling, Taiwan EPA battery 107 regulatory compliance notices BSMI 105 Canada 105 Class A 103 Class B 103 European Union 105 IEC EMC statement, worldwide 105 Japan 106 Korean 106 lasers 104 modifications 104 shielded cables 104 related documentation 7 removal 14 removing an interface card 15 report option Visual Manager 55 RFI/EMI connector hoods 104 technical support, HP 8 telephone numbers FCC questions 104 text symbols 7 traces clearing
hard AL_PA 42 link status 42 performance mode 43 port mode 42 Fibre Channel hosts, viewing and changing 47 FTP access 50 FTP Utility screen, illustrated 50 home page 33 Home page, illustrated 33 I/O configuration 41 IC image, illustrated 33 main menu 33 main menu, illustrated 33 mapping tasks, Fibre Channel viewing and changing 47 network configuration 36 Network Menu options 36 Network screen, illustrated 36 Ports menu, illustrated 41 reboot option 56 Reboot screen, illustrated 56 report options 55 Report