user guide hp StorageWorks network storage router e1200-160 Product Version: 2.0 Third Edition (April 2003) Part Number: 325741-001 The HP StorageWorks Network Storage Router provides bidirectional connectivity in a Fibre Channel Switched Fabric supporting Fibre Channel and SCSI devices. This user guide provides an overview, instructional information for configuration, and basic troubleshooting of the router.
© Hewlett-Packard Company, 2003. Hewlett-Packard Company makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. This document contains proprietary information, which is protected by copyright.
contents Contents About this Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Intended Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents Router Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Operating Environmental Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Shipping and Storing Environmental Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Configuration Overview . . .
Contents Ports Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fibre Channel Port Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SCSI Bus Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Discovery Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents Reset and Save Configuration to Factory Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . System Utilities Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . System Statistics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Event Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents A Serial and Ethernet Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .163 RJ-11 Serial Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164 RJ-45 Ethernet Cable Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165 B Controller LUN Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .167 General Commands . . . . . .
Contents 8 Network Storage Router e1200-160
about this guide F About this Guide About this Guide This user guide provides information to help you: ■ Install the Network Storage Router ■ Configure the Network Storage Router ■ Troubleshoot the Network Storage Router About this Guide topics include: ■ Overview, page 10 ■ Conventions, page 11 ■ Rack Stability, page 13 ■ Getting Help, page 14 Network Storage Router e1200-160 9
About this Guide Overview This section covers the following topics: ■ Intended Audience ■ Prerequisites ■ Related Documentation Intended Audience This guide is intended for administrators with a moderate knowledge level about network environments. Prerequisites Before you install this product, make sure you consider the items below.
About this Guide Conventions Conventions consist of the following: ■ Document Conventions ■ Text Symbols ■ Equipment Symbols Document Conventions The document conventions included in Table 1 apply in most cases.
About this Guide Text Symbols The following symbols may be found in the text of this guide. They have the following meanings. WARNING: Text set off in this manner indicates that failure to follow directions in the warning could result in bodily harm or death. Caution: Text set off in this manner indicates that failure to follow directions could result in damage to equipment or data. Note: Text set off in this manner presents commentary, sidelights, or interesting points of information.
About this Guide Any surface or area of the equipment marked with these symbols indicates the presence of a hot surface or hot component. Contact with this surface could result in injury. WARNING: To reduce the risk of personal safety from a hot component, allow the surface to cool before touching. Power supplies or systems marked with these symbols indicate the presence of multiple sources of power.
About this Guide Getting Help If you still have a question after reading this guide, contact an HP authorized service provider or access our website: http://www.hp.com. HP Technical Support In North America, call technical support at 1-800-652-6672, available 24 hours a day, 7 days a week. Note: For continuous quality improvement, calls may be recorded or monitored. Outside North America, call technical support at the nearest location.
About this Guide HP Authorized Reseller For the name of your nearest HP authorized reseller: ■ In the United States, call 1-800-345-1518 ■ In Canada, call 1-800-263-5868 ■ Elsewhere, see the HP website for locations and telephone numbers: http://www.hp.com.
About this Guide 16 Network Storage Router e1200-160
1 Introduction 1F The HP StorageWorks Network Storage Router provides bidirectional connectivity for Narrow/Wide Fast/Ultra-3 SCSI buses in a Fibre Channel Switched Fabric (FC-SW) environment.
Introduction External Features Overview Figure 1 illustrates the I/O panel of the router.
Introduction Power Indicator The router has one power LED. Power indicator LED definition: Green - Power has been applied to this module Yellow - Power-On-Self-Test (POST) in process or processor problems Serial Port The router is equipped with one serial port. See Figure 1 for the location of the serial port. The serial port can be used to access the Serial/Telnet user interface, which is used to locally manage and configure the router.
Introduction Functional Overview The router translates the Fibre Channel Protocol (FCP) to and from the SCSI Protocol. It transfers commands, data, and status information to and from Fibre Channel controllers and SCSI devices.
Introduction Fibre Channel to SCSI Protocol Process This section describes the steps the router uses to convert Fibre Channel host protocol to SCSI device protocol. Figure 3 and Table 3 illustrate and define this process. Figure 3: Converting Fibre Channel to SCSI process Table 3: Converting Fibre Channel to SCSI Item Description 1 A Fibre Channel host issues an encapsulated FCP protocol command packet to the router.
Introduction SCSI to Fibre Channel Protocol Process In this example, a SCSI host (initiator) on the SCSI bus issues commands and the information is passed through the router to a target on the Fibre Channel Storage Area Network (FC-SAN). Figure 4 is an illustration of the process and Table 4 defines each step.
Introduction LAN-free Backup and Restore The router can enable LAN-free backup/restore to allow the bulk of data traffic to be moved from the LAN to the storage area network (SAN). See Figure 5 for an illustration of this process. Fibre Channel ETHERNET SCSI TAPE UNIT SCSI DATA MOVEMENT SCSI TAPE UNIT StorageWorks Router Link/ Act Fibre Channel Pwr. Fibre Channel Pwr.
Introduction Shipping and Storing Environmental Requirements ■ Temperature: -40 to +55°C ■ Relative Humidity: 0 to 92% (non-condensing) Power Requirements 24 ■ VDC: 3V and 5V ■ 25 watt maximum power dissipation Network Storage Router e1200-160
Configuration Overview 2 2F The HP StorageWorks Network Storage Router can be configured and managed using several user interfaces (UI). Each UI is introduced in this chapter, along with information about common configuration settings.
Configuration Overview Router Default Ethernet Settings Some of the basic factory default values are: ■ IP address: http://1.1.1.1/ ■ Subnet mask: 255.255.255.0 ■ Gateway address: 0.0.0.0 ■ User name: root ■ Password: password HP recommends that you change these values from the defaults. All settings within the router configuration are preset with default values. These values are set to allow the router to be installed into most HP environments with little or no configuration changes.
Configuration Overview UI Overview The router supports the following user interfaces: ■ Visual Manager ■ Serial ■ Telnet ■ FTP Visual Manager Visual Manager lets you view and change router configuration from any standard Web browser. Information is dynamically generated in an HTML format so that any Web browser can access it.
Configuration Overview Telnet From most Microsoft® Windows® 9x, Windows NT®, and Windows 2000® systems, users can start a Telnet session from the DOS (command) shell after the IP address has been set. For complete information on accessing and using the Telnet UI, see Chapter 4, "Serial/Telnet User Interface." FTP The router supports the use of the FTP UI to perform several copy procedures using the put and the get commands. For more information, see Chapter 5, "FTP User Interface.
Configuration Overview Common Configuration Settings To provide connectivity between hosts and devices, the router must establish an address on each connected Fibre Channel network and SCSI bus. The following paragraphs discuss configuration settings that are commonly modified and are available in the Visual Manager UI and the Serial/Telnet UI. For procedural information on accessing and changing these settings, see Chapter 3, "Visual Manager User Interface," and Chapter 4, "Serial/Telnet User Interface.
Configuration Overview Fibre Channel Port Configuration By default, the configuration of the Fibre Channel ports is set to N_Port, forcing the router to negotiate a fabric only mode. Note: By default, the Fibre Channel port speed is set to 2 Gb/s. Changes to the Fibre Channel port speed must be manually set, such as for 1 Gb/s.
Configuration Overview Mapping involves pairing FC_AL_PA to SCSI target address. The HBA will claim enough SCSI bus entries to allow up to 125 Fibre Channel targets to be mapped to SCSI Bus: Target entries. This is usually done by a fixed mapping of AL_PA to Bus: Target. In such a configuration, the router corresponds to a Bus: Target identifier, with the attached SCSI devices appearing as logical units (LUNs). Operating systems can extend the available SCSI limit of 15 targets per bus.
Configuration Overview Note: The router can respond to multiple Target IDs on a SCSI bus. Both Fibre Channel ports and SCSI buses have predefined maps. There are four predefined maps: ■ Indexed Map ■ Port 0 Device Map ■ Auto Assigned Maps ■ SCC Map When a host sends a command, the router will select which map to use, based on the port receiving the command and the ID of the host sending the command.
Configuration Overview Buffered Tape Writes This option is designed to enhance system performance by returning status on consecutive write commands prior to the tape device receiving data. If data does not transfer correctly, the router returns a check condition on a subsequent command. Commands other than Write are not issued until status is received for any pending Write, and status is not returned until the device completes the command.
Configuration Overview 34 Network Storage Router e1200-160
Visual Manager User Interface 3 3F The HP StorageWorks Visual Manager user interface (UI) provides a graphical format that is used to remotely view and change router configurations. Use the Microsoft Internet Explorer or Netscape (version 6.2 or greater) Web browsers to access Visual Manager. Information is presented in HTML format in accordance with the W3C specification for HTML 3.2. Current W3C recommendations and other technical documents can be found at www.w3.org/TR/.
Visual Manager User Interface ■ Ports Menu, page 54 — Fibre Channel Port Configuration — SCSI Bus Configuration ■ Discovery Menu, page 64 ■ Mapping Menu, page 65 — Common Fibre Channel and SCSI Mapping Tasks — SCSI Mapping Tasks ■ Statistics Menu, page 74 ■ Utilities Menu, page 75 — FTP Utility Access — Trace Settings Configuration — Current, Previous, and Last Assert Trace Displays — Clear Current Traces and Clear Assert Traces — Event Log Configuration — Event Log Display — Clear Event Log 36
Visual Manager User Interface Visual Manager Menu Tree Main Menu Figure 6: Visual Manager Main menu tree Network Storage Router e1200-160 37
Visual Manager User Interface Visual Manager Access Visual Manager (VM) can be accessed from any standard Web browser: 1. Connect a 10/100BaseT Ethernet cable to the back of the router. 2. Apply power to the connected SCSI and/or Fibre Channel devices. 3. Apply power to the host computer. 4. Enter the router IP address in the address field of the Web browser of the host computer. Note: To access VM, the router must be assigned a valid IP address.
Visual Manager User Interface 6. Enter the authorized user name and password. The username and password are case-sensitive. The default user name is root and the default password is password. Figure 7: Password Dialog Box Note: HP recommends changing the user name and password from the defaults. Note: To end the current session of VM, the browser window must be closed. Navigating the browser to another URL does not end the current session.
Visual Manager User Interface Visual Manager Best Practices The following recommendations should be observed: ■ A standard keyboard and mouse must be used to navigate in the VM. ■ The router is shipped with a configuration of default settings that is acceptable for most system environments. Few changes to the configuration should be necessary. ■ After any configuration changes are made, depending on the menu option, select Submit or Configure to send changes from the Web browser to the router.
Visual Manager User Interface Main Menu The Main Menu home page is displayed whenever VM is accessed. The home page contains status information, including a physical image of the router. Figure 8 is an example of the home page.
Visual Manager User Interface Home page information includes: ■ The HP logo is located in the upper left corner of the page. Figure 9 is an example of this portion of the home page screen. If the Internet is accessible to the host, click the HP logo to open the website. Figure 9: HP logo ■ An illustration of the router is located near the top of the home page. Figure 10 is an example of this portion of the home page screen.
Visual Manager User Interface ■ Main Menu options: — Home displays router status information. — System configures standard system components. — Ports configures the Fibre Channel port and SCSI buses. — Discovery displays devices and discovers new devices. — Mapping displays and configures maps. — Statistics displays router statistics. — Utilities configures utility settings. — Report displays system information. — Reboot restarts the router.
Visual Manager User Interface System Menu The System Menu is accessed from the Main Menu and is used to view and configure serial, network, trap, active fabric, clock, and power supply components. Figure 11 is an example of the System page. Figure 11: System page System page tasks: 44 ■ Serial configures the baud rate. ■ Network configures Ethernet settings. ■ SNMP is not supported. ■ Active Fabric configures Active Fabric settings. ■ User configures user security settings.
Visual Manager User Interface ■ Real-Time Clock configures system date and time. ■ Reset Menu ■ Factory Settings Reset restores factory default settings. Each menu option is discussed in the following paragraphs.
Visual Manager User Interface Serial Configuration The Serial screen is used to change the baud rate for the serial port. Figure 12 is an example of the Serial screen. If the Autobaud feature is being used, it may not be necessary to set the baud rate. . Figure 12: Serial screen The current baud-rate setting is displayed. Note: HP recommends setting the baud rate to 115200.
Visual Manager User Interface Network Configuration The Network screen is used to enter network settings, including Ethernet settings. Figure 13 is an example of the Network screen. Figure 13: Network screen Network Menu options: ■ Network Settings changes the hostname. ■ Port Configuration changes Ethernet configuration settings. Each of these Network Menu options is discussed in the following sections.
Visual Manager User Interface Port Configuration - Ethernet Settings (Service Mode - Restricted Access) To change the Ethernet configuration settings, select the Ethernet port icon. The Ethernet Configuration dialog box is displayed. See Figure 14 for an example of the Ethernet Configuration dialog box.
Visual Manager User Interface The Ethernet physical address is always assigned by the manufacturer. ■ IP address (default: 1.1.1.1) is the IP address of the router. ■ Subnet Mask (default: 255.255.255.0) is the IP subnet mask for the router. ■ IP Gateway (default: 0.0.0.0) is the IP address of the gateway for the Ethernet network connected to the router. ■ DHCP enables or disables support for Dynamic Host Configuration Protocol (DHCP).
Visual Manager User Interface Active Fabric Configuration The Active Fabric screen allows setup of Active Fabric options. Figure 15 is an example of the Active Fabric screen. Figure 15: Active Fabric screen Active Fabric settings: ■ Number of Controller LUNs (default: 1) sets the number of controller LUNs reported by the router. The number must be in the range of 0 through 4. For information on controller LUN commands, see Appendix B, "Controller LUN Commands.
Visual Manager User Interface User Configuration The User screen is used to set up router security. Figure 16 is an example of the User screen. Figure 16: User screen: security settings User settings: ■ User Name (default: root) is any alphanumeric combination. ■ Password (default: password) is any alphanumeric combination. The user name and password should be unique and kept confidential. HP recommends using a combination of letters and numbers when creating the user name and password.
Visual Manager User Interface Real-Time Clock Configuration The Real Time Clock screen is used to set the system time and date. Figure 17 is an example of the Real-Time Clock screen. Figure 17: Real-Time Clock screen Real-Time Clock settings: ■ Date Settings sets the month, date, and year. Use a four-digit number to represent the year. ■ Day of Week sets the day of week. ■ Time Settings sets the hours, minutes, and seconds. The system clock is a 24-hour clock.
Visual Manager User Interface Reset Menu The Reset Menu is used to reset the router to factory default settings. Figure 18 is an example of the Reset Menu. Figure 18: Reset to Factory Default screen Current router activities are disrupted while the unit resets the configuration to the factory defaults and saves those options to FLASH memory. Caution: Resetting the router configuration to the factory defaults will delete custom maps or map changes.
Visual Manager User Interface Ports Menu Accessed from the Main Menu, the Ports Menu is used to view and to modify configuration settings of the Fibre Channel port and SCSI buses. Figure 19 is an example of the initial Ports Menu. Figure 19: Ports menu The initial screen display of the Ports Menu includes summary information about each Fibre Channel port and SCSI bus in the router.
Visual Manager User Interface Note: To view or change configuration settings of a specific port or bus, select it from the menu bar on the left side of the screen or select the port or bus from the router image at the top of the screen. To make changes, modify the setting and then click Submit. Ports Menu tasks: ■ Fibre Channel Port configuration changes Fibre Channel port settings. ■ SCSI Bus configuration changes SCSI bus settings. Each Ports Menu option is discussed in the following subsections.
Visual Manager User Interface Fibre Channel Port Configuration When the Fibre Channel port is selected in Ports Menu, the Fibre Channel Configuration screen is displayed. Figure 20 is an example of the Fibre Channel Configuration screen. Figure 20: Fibre Channel Configuration screen Fibre Channel port settings: 56 ■ Link Status indicates the port link status. ■ Port Name High sets a new value for the World Wide Port Name High.
Visual Manager User Interface Caution: If the following configuration settings are incorrectly set, processing difficulties may occur. Before changing these settings, evaluate the need for the change and verify the desired setting. HP recommends backing up the router configuration to an external file before making changes to these settings. ■ Port Name Low sets a new value for the World Wide Port Name High. (Service Mode - Restricted Access) ■ Port Mode (default: N_Port) sets the port mode.
Visual Manager User Interface — Manual Discovery Only (default) sets discovery of new devices to occur only after the user selects the Discovery option from the Main Menu or when a Registered State Change Notification (RSCN) is received from a fabric. Note: SCSI devices attached to a Fibre Channel must be mapped as sequential Fibre Channel LUNs starting at LUN number 00.
Visual Manager User Interface ■ Performance Mode (default: 2 Gb/s) toggles between 1 Gb/s and 2 Gb/s. Note: If Performance Mode is set incorrectly and the router is plugged into a Loop or Fabric, the unit may receive Framing errors due to the incorrect Fibre Channel link speed. ■ Override Settings (service mode-restricted access) enhances interoperability with some storage devices that require special consideration during setup of the router configuration menus.
Visual Manager User Interface SCSI Bus Configuration When a SCSI bus is selected in the Ports Menu, the SCSI Bus Configuration screen is displayed. Figure 21 is an illustration of the SCSI Bus Configuration screen. Figure 21: SCSI Bus Configuration screen SCSI bus configuration settings: 60 ■ Primary Initiator ID (default: 7) must be a unique ID. ■ Alternate Initiator ID (service mode-restricted access) (default: none) will be used if the primary ID is taken. Must be a unique ID.
Visual Manager User Interface Caution: If this configuration setting is incorrectly set, processing difficulties may occur. Before changing this setting, evaluate the need for the change and verify the desired setting. HP recommends backing up the router configuration to an external file before making changes to this setting. Note: Target IDs must be setup before mapping devices on the SCSI bus.
Visual Manager User Interface When enabled, Buffered Tape Writes enhance system performance. Buffered Tape Writes return status on consecutive write commands prior to the tape device receiving data. ■ Default Map (default: auto-assigned) sets the current mapping mode for the selected bus. Caution: If this configuration setting is incorrectly set, processing difficulties may occur. Before changing this setting, evaluate the need for the change and verify the desired setting.
Visual Manager User Interface — Synchronous Parameter Override enables or disables parameters for synchronous negotiation. — Synchronous Period (default: 40) sets the maximum number of seconds allowed for negotiation. — Synchronous Offset (default: 16) sets the maximum variation in transfer rate that can be negotiated in megabytes per seconds (MB/s). — Ultra SCSI-3 Negotiation enables or disables Ultra SCSI-3 support for the selected Target ID.
Visual Manager User Interface Discovery Menu Accessed from the Main Menu, the Discovery Menu is used to view Target devices and discover new Target devices. Figure 22 is an example of the Discovery page. Figure 22: Discovery page To perform a manual discovery: 1. Select the Fibre Channel port or SCSI bus from the menu bar or the router image. 2. Select Go.
Visual Manager User Interface Mapping Menu Each physical port/bus on the router can have the following maps: Table 5: Device Map Types Map Type System/User Generated Fibre Channel or SCSI Auto Assigned System Fibre Channel and SCSI Indexed (default) System Fibre Channel and SCSI Port <0> Device System Fibre Channel SCC System Fibre Channel Note: Port 0 Device Map is the HP recommended map to be used for editing and assigning oncoming hosts.
Visual Manager User Interface Common Fibre Channel and SCSI Mapping Tasks Although the initial screen display for Fibre Channel and SCSI maps differs slightly, the available actions are the same. Figure 23 is an illustration of the Fibre Channel mapping screen. Figure 23: Initial Mapping screen Mapping screen options: ■ Select Host adds a known host. To select a previously set up host, expand the Select Host drop-down box and select the host from the list.
Visual Manager User Interface ■ Add Map adds a new map. To add an undefined map, type the name of the map in the Add Map field and then click Add. ■ Select Map adds a known map. To select a previously set up map, expand the Select Map drop-down box and select the map from this list. ■ Edit/View Map displays or changes map information. Viewing and changing map information is discussed in the following paragraphs. ■ Delete Map deletes the current map.
Visual Manager User Interface Viewing and Changing Fibre Channel Host Information To view or change current host information: 1. In the Mapping Menu screen, select the desired Fibre Channel port. 2. Click Edit/View in the Host section of the screen. The Fibre Channel Host Name dialog box is displayed. Current host information is shown at the top of the dialog box. 3. Enter the new settings and then select Modify.
Visual Manager User Interface Viewing and Changing Fibre Channel Map Information Note: Port 0 Device Map is the HP recommended map to be used for editing and assigning oncoming hosts. The Indexed (default) map should not be used for editing, even though the user is able to edit this map. To view or change current Fibre Channel map information: 1. In the Mapping Menu screen, select the Fibre Channel port. 2. Select Edit/View in the Map section of the screen. The Fibre Channel Map dialog box is displayed.
Visual Manager User Interface To delete map entries, expand the Delete Map Item LUN drop-down box, select the LUN, and then click Delete. To delete a range of LUNs, select the beginning LUN to delete from the “from” drop-down box and select the last LUN to delete from the “to” drop-down box. ■ Discovered Device Entry adds a discovered device to the map.
Visual Manager User Interface SCSI Mapping Tasks Configuration tasks for SCSI mapping include: ■ Viewing and Changing SCSI Host Information ■ Viewing and Changing SCSI Map Information Each task is discussed in the following paragraphs. Viewing and Changing SCSI Host Information To view or change current SCSI host information: 1. In the Mapping Menu screen, select the desired SCSI bus. 2. Click Edit/View in the Host section of the screen. The SCSI Host Name dialog box is displayed.
Visual Manager User Interface Viewing and Changing SCSI Map Information To view or change current SCSI map information: 1. In the Mapping Menu screen, select the desired SCSI bus. 2. Select Edit/View in the Map section of the screen. The SCSI Map dialog box is displayed. Current map information is shown at the top of the dialog box. 3. Enter the new settings and then click the appropriate action button. Figure 25 is an example of the SCSI Map dialog box.
Visual Manager User Interface Note: Auto-Assigned and SCC maps cannot be modified, cleared, filled, or have entries deleted. Note: Map settings are saved to memory when any button within the page is selected. Note: SCSI maps can be filled or devices can be added to them only when at least one SCSI Target ID has been enabled in the SCSI Bus Configuration Menu. SCSI Map settings: ■ Clear Map clears all entries from the current map. ■ Fill Map fills in the current map.
Visual Manager User Interface Statistics Menu Accessed from the Main Menu, the Statistics Menu is used to display Fibre Channel port and SCSI bus information. Figure 26 is an example of the Statistics Menu. Figure 26: Statistics menu To view information for a specific port or bus, click the component on the menu bar or the router image. To refresh the display, select Reset SCSI system statistics.
Visual Manager User Interface Utilities Menu Accessed from the Main Menu, the Utilities Menu is used to view and configure utility options. Figure 27 is an example of the Utilities Menu. Figure 27: Utilities menu Utility Menu tasks: ■ FTP Utility access opens an FTP session. ■ Trace Settings configuration configures trace settings. ■ Current Traces display displays current trace information. ■ Previous Traces display displays previous trace information.
Visual Manager User Interface ■ Event Log Settings configures Event Log settings. ■ Event Log display displays the Event Log. ■ Clear Event Log clears the Event Log. Each Utility Menu option is discussed in the following sections.
Visual Manager User Interface FTP Utility Access The FTP utility screen is used to open an FTP session. Figure 28 is an example of the FTP utility screen. Figure 28: FTP Utility screen The FTP utility requires the use of a JAVA applet and prompts for permission to install the applet, if needed. If the prompt is displayed, follow the onscreen instructions to complete the installation. The FTP utility then prompts for permission to run the applet.
Visual Manager User Interface To open an FTP session: 1. Enter the User Name, Password, and the IP address of the router. 2. Click Connect. 3. Select the local file to upload or download. If necessary, click Browse to scroll through a file list. The following file types can be uploaded to the router: ■ Configuration (.cfg) ■ Firmware (.dlx) The following file types can be downloaded from the router: ■ Configuration (.cfg) ■ Traces for the current boot cycle (curtrace.
Visual Manager User Interface Trace Settings Configuration The Trace Settings screen is used to configure the trace settings. Figure 29 is an example of the Trace Settings screen. Figure 29: Trace Settings screen Current Trace settings are displayed. To change the settings, use the drop-down boxes and choose the desired setting. After all changes are completed, select Submit.
Visual Manager User Interface Table 6 is a brief description list of the trace settings. Table 6: Trace Settings Setting 80 Description General Errors Displays the most serious errors and exception conditions. FCP Transport Fibre Channel Protocol transport functionality will be monitored and recorded. PS Transport Parallel SCSI transport functionality will be monitored and recorded. PS Driver Parallel SCSI driver functionality will be monitored and recorded.
Visual Manager User Interface Current, Previous, and Last Assert Trace Displays These three Utilities Menu screens show trace information. The Current Traces screen shows data since the router was last booted. The Previous Traces screen shows data from the last boot cycle. The Last Assert Traces screen shows data since the last assertion. Figure 30 is an example of the Current Traces screen.
Visual Manager User Interface Clear Current Traces and Clear Assert Traces These Utilities Menu screens are used to clear the current trace buffer or the assert trace buffer. Current router activities will not be disrupted while the buffer is cleared. Figure 31 is an example of the Clear Current Trace Buffer screen.
Visual Manager User Interface Event Log Configuration The Event Log Setting screen is used to configure Event Log filters. Figure 32 is an example of the Event Log Filter configuration screen. Figure 32: Event Log Settings screen Event Log settings: ■ Log All Events ■ Disable/Enable Event Logging ■ Log Error Events ■ Log Notify Events Event logging captures the last 215 events and then starts overwriting the log.
Visual Manager User Interface Event Log Display The Event Log screen is used to view the Event Log. Figure 33 is an example of the Event Log display screen.
Visual Manager User Interface Clear Event Log The Clear Event Log screen is used to clear the Event Log. Figure 34 is an example of the Clear Event Log screen. Current router activities will not be disrupted.
Visual Manager User Interface Report Menu Accessed from the Main Menu, the Report screen displays a consolidated view of all system information, including environmental conditions. Figure 35 is an example of the Report screen.
Visual Manager User Interface Reboot Option Router reboots are executed using this router Main Menu option. Figure 36 is an example of the Reboot screen. When the router is rebooted, current router activities will be disrupted. All submitted configuration changes will be activated during the boot-up process. Caution: Confirm there is no activity, such as a backup in progress, before initiating a reboot as router activities will be disrupted.
Visual Manager User Interface 88 Network Storage Router e1200-160
Serial/Telnet User Interface 4 4F The Serial/Telnet User Interface (UI) is used to configure and manage the HP StorageWorks Network Storage Router. This chapter describes the configuration menus and option tasks available in the Serial/Telnet UI. Note: Unless otherwise indicated, configuration changes take effect when the router reboots. During the router start up process, the Serial/Telnet UI displays initial power-up messages.
Serial/Telnet User Interface ■ Configuration Menu, page 96 — Baud Rate Configuration — Ethernet Configuration — Fibre Channel Configuration — Parallel SCSI Configuration — Device Mapping — Trace and Event Settings Configuration — Real-Time Clock Configuration — Active Fabric Configuration — Save Configuration — Restore Last Saved Configuration — Reset and Save Configuration to Factory Defaults ■ System Utilities Menu, page 130 — System Statistics — Event Log ■ Trace Dump Menu, page 140 — Saving Copies
Serial/Telnet User Interface Serial/Telnet Menu Tree Main Menu Network Storage Router e1200-160 91
Serial/Telnet User Interface Telnet UI Access To open a Telnet session, the IP address of the router and a Telnet client utility are required. Note: After each reboot, a new Telnet session must be started. If the router is reset to factory settings, the Ethernet port will have to be re-configured using the serial interface. From most Windows 9x, Windows NT, and Windows 2000 systems, a Telnet session can be started from the Command (DOS) shell using the following steps: 1.
Serial/Telnet User Interface 4. Configure the serial port settings, as listed in Table 7. Table 7: Terminal Configuration Settings BAUD Rate Autobaud, 9600, 19200, 38400, 57600, 115200 Data Bits 8 Stop Bit 1 Parity None Flow Control XON/XOFF Note: HP recommends setting the baud rate to 115200. 5. After completing the serial port configuration, select OK to start a serial session. 6.
Serial/Telnet User Interface Power up Messages When power is applied to the router, a series of messages is displayed on the serial terminal or terminal emulation program. Figure 37 is an example of these power-up messages. Figure 37: Power Up messages Note: Throughout this chapter, XX represents value fields.
Serial/Telnet User Interface Serial/Telnet UI Main Menu The Main Menu is the starting point for all configuration sub-menus and tasks. Figure 38 is an illustration of the router Main Menu. Note: If the power up messages and the Main Menu are not displayed, check the serial port settings. Figure 38: Serial/Telnet main menu Main Menu options: ■ 1) Perform Configuration enters router configuration settings. ■ 2) System Utilities displays system statistics and perform diagnostic tests.
Serial/Telnet User Interface Configuration Menu The Configuration Menu is used to configure the router. Figure 39 is an illustration of the Configuration Menu. Figure 39: Configuration menu Note: The router is shipped with a configuration of default settings that is acceptable for most system environments. Few changes to the configuration should be necessary. After any configuration changes are made, select A) Save Configuration to record the changes.
Serial/Telnet User Interface ■ 5) Device Mapping modifies map and host settings. ■ 6) Trace and Event Settings Configuration modifies trace and event filter settings. ■ 7) Real-Time Clock Configuration sets the system clock. ■ 8) Active Fabric Configuration enables and disables server-free backup and changes the number of controller LUNs. ■ A) Save Configuration saves changes to memory. ■ B) Restore Last Saved Configuration reverts to the previous configuration.
Serial/Telnet User Interface Note: The asterisk (*) symbol indicates the current setting for the baud rate. Note: If the Autobaud feature is being used, it is not necessary to set a baud rate. Ethernet Configuration In the Configuration Menu, choose 2) Ethernet and SNMP (SNMP not supported) Configuration to set up the Ethernet network. When this option is selected, the Ethernet Configuration Menu is displayed. Current Ethernet settings are displayed, along with available Ethernet configuration options.
Serial/Telnet User Interface To view or change configuration settings: 1. Select a menu option 2. Make the configuration changes 3. Select X) Return to previous menu 4. Select A) Save Configuration to record the changes. Ethernet Configuration Menu options: ■ 1) Change IP address (default: 1.1.1.1) changes the router IP address. ■ 2) Change IP Subnet Mask (default: 255.255.255.0) changes the router Subnet mask. ■ 3) Change IP Gateway (default: 0.0.0.0) changes the IP gateway for the Ethernet network.
Serial/Telnet User Interface ■ 7) Toggle DHCP Configuration enables or disables support for Dynamic Configuration Protocol. When DHCP is enabled, the router will request a dynamic IP address from the DHCP server on the Ethernet network. Some DHCP servers allow a lease reservation to be set up for an IP address by providing the server with the Ethernet MAC address. The DHCP server will then always provide the same IP address to the router.
Serial/Telnet User Interface Fibre Channel Configuration In the Configuration Menu, choose 3) Fibre Channel Configuration to configure the Fibre Channel port. The Fibre Channel Configuration Menu allows the configuration of ALPA settings, discovery mode, tape backup settings, port mode, default map, and override settings. Figure 42 is an illustration of the Fibre Channel Configuration Menu.
Serial/Telnet User Interface Fibre Channel Configuration Menu options: Caution: If these configuration settings are incorrectly set, processing difficulties may occur. Before changing these settings, evaluate the need for the change and verify the desired setting. HP recommends backing up the router configuration to an external file before making changes to these settings. ■ 1) Change World Wide Name High (service mode-restricted access) changes the World Wide Port Name High.
Serial/Telnet User Interface Note: SCSI devices attached to a Fibre Channel port must be mapped as sequential Fibre Channel LUNs starting at LUN number 00. Skipping LUN numbers is not recommended when mapping Fibre Channel LUNs because Fibre Channel Discovery stops the discovery process whenever an empty LUN position is found. Caution: If these configuration settings are incorrectly set, processing difficulties may occur.
Serial/Telnet User Interface A sub-screen is displayed, listing the following options: — 1) Toggle Hi-Sup Bit Settings changes the Hi-Sup Bit settings. Options include Set and Clear. — 2) Toggle Forcing FCP Response Code for HP HBA #223180-B21 and #120186-001, changes the forcing of the FCP response code. Options include Off and On. — 3) Toggle Initiator Bit Setting in PRLI_ACC changes the Initiator bit setting. Options include Set and Clear.
Serial/Telnet User Interface Parallel SCSI Configuration In the Configuration Menu, choose 4) Parallel SCSI Configuration to configure the SCSI buses. The Parallel SCSI Configuration Menu allows the configuration of the SCSI discovery mode, SCSI bus reset, termination mode, tape backup settings, and default current map. Figure 43 is an illustration of the Parallel SCSI Configuration Menu. Figure 43: SCSI Configuration menu Current settings for the selected SCSI bus are displayed.
Serial/Telnet User Interface SCSI Configuration Menu options: ■ 1) Edit Initiator and Target Settings changes the SCSI Initiator and Target settings. The SCSI Initiator and Target Menu sub-screen is displayed, listing the following options: — 1) Enable/Disable SCSI Initiator enables or disables the SCSI Initiator. Options are Enabled and Disabled. — 2) Select primary and select/enable alternate SCSI ID sets the primary and alternate initiator SCSI IDs (defaults: primary = 7; alternate = none).
Serial/Telnet User Interface Note: This value should be set to no less than 250ms, according to the SCSI standard for Reset-to-Selection Time. HP recommends setting the value to at least 30 seconds to ensure all SCSI devices complete their individual POST. ■ 5) Set SCSI Termination Mode enables or disables the SCSI termination mode. ■ 6) Edit SCSI Target Override Settings changes the SCSI Target overrides.
Serial/Telnet User Interface Device Mapping Each physical port/bus on the router can have the following maps: Table 8: Device Map Types Map Type System/User Generated Fibre Channel or SCSI Auto Assigned System Fibre Channel and SCSI Indexed (default) System Fibre Channel and SCSI Port <0> Device System Fibre Channel SCC System Fibre Channel Each map has a unique name and map ID; one of the maps must be identified as the “current” map for the router to use.
Serial/Telnet User Interface Device Mapping Configuration Menu options: ■ 1) Select Current Map indicates which map is to be the current map. ■ 2) Display Current Map displays the current map. ■ 3) Edit Current Map changes current map settings. ■ 4) Edit Host List for Current Map changes the host information for the current map. ■ 5) Display Device List displays the device list. ■ X) Return to previous menu returns to previous menu.
Serial/Telnet User Interface Caution: If this configuration setting is incorrectly set, processing difficulties may occur. Before changing this setting, evaluate the need for the change and verify the desired setting. HP recommends backing up the router configuration to an external file before making changes to this setting. To indicate which map is to be the current map, type the number that corresponds to the desired map.
Serial/Telnet User Interface Figure 47: SCSI Current Map Display screen Editing the Current Map In the Device Mapping Configuration Menu, choose 5) Edit Current Map to edit the current map. The Map Edit Menu subscreen is displayed. Figure 48 is an illustration of the Map Edit Menu.
Serial/Telnet User Interface Note: Auto-Assigned and SCC Maps cannot be edited. Map Edit Menu options: ■ 1) Edit Name changes the name of the current map. ■ 2) Edit Map Entries changes the content of the current map. ■ 3) Clear Map erases all entries from the current map. ■ 4) Fill Map automatically completes the entries for the current map. Each editing option is discussed in the following sections.
Serial/Telnet User Interface Figure 49: Edit Map Entries for a Fibre Channel map Figure 50: Edit Map Entries for a SCSI map Edit Map Entries options: ■ Next (N) scrolls down the list of map entries. ■ Previous (P) scrolls up the list of map entries. ■ Add (A) adds new map entries.
Serial/Telnet User Interface ■ Create (C) creates a new map entry for a newly added device. ■ Remove Gaps (R) removes gaps in the listed sequence of LUNs. ■ Delete (D) deletes a map entry. ■ Exit (X) returns to the previous menu. Scrolling between Display Pages of the Edit Map Entries Screen To scroll up and down the map entries, select P or N. Adding a Map Entry to a Fibre Channel Map To add a new entry to a Fibre Channel map: 1. In the Map Edit Entries screen, select Add (A). 2.
Serial/Telnet User Interface 4. In the Device List, to add a listed device to the map, enter the number from the “Num” column. If the selected device is already mapped, an error message will appear, warning the user about adding a duplicate device. Adding a Map Entry to a SCSI Map To add a new entry to a SCSI map: 1. In the Edit Map Entries screen, select Add (A). 2. Enter a Target/LUN ID combination.
Serial/Telnet User Interface Figure 52 is an example of the screen display when creating an entry for a Fibre Channel map. Figure 52: Creating a map entry for a Fibre Channel map Note: If the device being added is a SCSI device, the Target ID and LUN ID must be entered. The Target ID must already be defined in the SCSI configuration. Creating an Entry for a SCSI Map To pre-enter a map entry for devices that are not yet online, select Create (C).
Serial/Telnet User Interface Figure 53: Creating an entry for a SCSI map Note: If the device being added is a Fibre Channel device, the Node WWN, Port WWN, and LUN ID must be entered. Note: If this device is a duplicate of a device currently present in the device list, an error message will be displayed. Removing Gaps in the Map To remove any incremental gaps in the sequence of LUNs listed in the table, in the Edit Map Entries screen, select Remove (R).
Serial/Telnet User Interface Note: Some operating systems require gaps be removed in the mapping table in order to detect all devices. Deleting a Map Entry To delete an entry from a map, in the Edit Map Entries screen, select Delete (D). For Fibre Channel maps, at the prompt, either enter the LUN ID of the LUN to delete or enter D to delete multiple LUNs. For SCSI maps, at the prompt, enter the Target ID and LUN ID of the LUN to delete or enter D to delete multiple LUNs.
Serial/Telnet User Interface Figure 54: Host List Display for Fibre Channel maps Figure 55: Host List Display for SCSI maps Host List Edit Display options: ■ Next (N) scrolls down the Host List. ■ Previous (P) scrolls up the Host List. ■ Add (A) adds a new host to the Host List. ■ Delete (D) deletes a host from the Host List. ■ Edit (E) edits host information. ■ Exit (X) returns to the previous menu.
Serial/Telnet User Interface Each of the options is discussed in the following paragraphs. Scrolling between the Display Pages of the Host List Edit Screen To scroll up and down the host entries, select P or N. Selecting a Host To select a host from the list, enter the number displayed in the “N#” or the “Num” column at the left of the screen. Adding a Host to the Host List To add a host to the Host List, select Add (A).
Serial/Telnet User Interface Figure 56 is an example of the screen display when adding a host to the Host List of an FCP host. Figure 56: Adding a host to the host list - FCP host If the host is a SCSI host, the host name and the initiator ID must be entered. Deleting a Host from the Host List To remove a host from the Host List, select Delete (D). After entering the number of the host to delete, a confirmation prompt is displayed. Editing Host information To change host information, select Edit (E).
Serial/Telnet User Interface Figure 57 is an example of editing host information for a Fibre Channel port.
Serial/Telnet User Interface Figure 58 is an example of editing host information for a SCSI bus. Figure 58: Editing host information for a SCSI bus Displaying the Entire Device List In the Device Mapping Configuration Menu, choose 8) Display Device List to view the entire device list for all buses and ports. The Entire Device List screen is displayed.
Serial/Telnet User Interface Figure 59 is an illustration of the Entire Device screen. Figure 59: Entire Device List screen Note: The entire list of maps may not fit on one screen. Select N or P to go back and forth between screens displaying more maps. Select X to return to the previous menu. Trace and Event Settings Configuration In the Configuration Menu, choose 5) Trace and Event Settings Configuration to view and change Trace and Event settings.
Serial/Telnet User Interface Trace Settings Menu options: ■ 1) Trace Settings Configuration configures the trace settings. ■ 2) Event Settings Configuration configures the event settings. Each of these options is discussed in the following sections. Configuring Trace Settings In the Utility Trace Settings Menu, 1) Trace Setting Configuration is used to modify trace levels. Two pages of trace level settings are displayed. Figure 61 and Figure 62 are illustrations of the two Trace Settings screens.
Serial/Telnet User Interface 4. Press Enter to display the second Trace Settings page. Figure 62 is an illustration of the second Trace Settings page. 5. If needed, change the settings in the second Trace Settings page. Note: Be sure to set the clock and date in the Real Time Clock Configuration Menu so that event logging is accurate.
Serial/Telnet User Interface 1. To change any of the settings in this screen, enter the number of the desired setting (1, 2, 3, or 4) that corresponds to the option that needs to be changed. Settings include: ■ 1) Log All Events (default) ■ 2) Disable Event Logging ■ 3) Error Events ■ 4) Notify Events 2. Before leaving the page, activate the new setting by entering U) Update Current Operating Trace levels. 3.
Serial/Telnet User Interface Active Fabric Configuration In the Configuration Menu, select 8) Active Fabric Configuration to enter Active Fabric options. Figure 65 is an illustration of the Active Fabric Configuration Menu. Figure 65: Active Fabric Configuration menu Active Fabric Configuration Menu options: ■ 1) Change the number of controller LUNs (default: 1) changes the number of controller LUNs. This setting is a number in the range of 0 through 4.
Serial/Telnet User Interface Restore Last Saved Configuration In the Configuration Menu, B) Restore Last Saved Configuration is used to revert to the previous configuration. This can be useful when configuration changes have been made, and the user wishes to return to the previous configuration. Reset and Save Configuration to Factory Defaults In the Configuration Menu, choose C) Reset and Save Configuration to reset the router configuration to its initial settings (factory default).
Serial/Telnet User Interface System Utilities Menu Accessed from the router Main Menu, the System Utilities Menu is primarily used to view system information. To access the System Utilities Menu, in the router Main Menu, choose 2) System Utilities. Figure 66 is an illustration of the System Utility Menu. Figure 66: System Utility menu System Utility Menu options: ■ 1) System Statistics Menu displays a variety of system status information. ■ 2) Event Log displays the system Event Log.
Serial/Telnet User Interface System Statistics In the System Utility Menu, select 1) System Statistics Menu to view system status information. Figure 67 is an illustration of the System Status/Statistics Menu. Figure 67: System Statistics menu System Statistics Menu options: ■ 1) Display System Status displays router status information. ■ 2) Display Fibre Channel Protocol Status displays Fibre Channel status information. ■ 3) Display Parallel SCSI Protocol Status displays SCSI status information.
Serial/Telnet User Interface Figure 68: System Status menu System Status Menu options: ■ 1) Display memory statistics displays memory usage information ■ 2) Display active tasks displays a list of current tasks. ■ 3) Display stack usage displays current stack information. ■ 4) Display SCSI Protocol Resources displays SCSI protocol information.
Serial/Telnet User Interface ■ 2) Display Attached Fibre Channel Devices displays a list of devices attached to this Fibre Channel port. ■ 3) Display Fibre Channel Resource Status displays Fibre Channel resource transport information. ■ 4) Display Fibre Channel Driver Resource Status displays Fibre Channel driver information. Each menu option and example screen displays are discussed in the following subsections.
Serial/Telnet User Interface Table 9: Link Status Definitions Link Status Field 134 Definition LinkState Current Fibre Channel link status. AL_PA Arbitrated loop physical address. (not supported) InDevDataSeqs Number of Device Data sequences received by this port. OutDevDataSeq Number of Device Data sequences transmitted by this port. InLnkDataSeqs Number of Link Data frames received by this port. InP_BSYFrames Number of P_BSY frames received by this port.
Serial/Telnet User Interface Viewing Attached Fibre Channel Devices To view a list of the devices attached to this port: 1. In the Fibre Channel Status Menu, choose 2) Display Attached Fibre Channel Devices. The Fibre Channel Device Display page is displayed. Figure 71 is an illustration of the Fibre Channel Device Display page when it is first displayed. Figure 71: Fibre Channel Device Display page 2. To refresh the display, select R) Refresh Device Display.
Serial/Telnet User Interface Viewing Fibre Channel Resource Transport Information To view FCP transport information, in the Fibre Channel Status Menu, choose 3) Display Fibre Channel Resource Status. The FCP Transport Queues page is displayed. The FCP Transport Queue page has no options. It is used only for viewing resource status. Figure 72 is an illustration of the FCP Transport Queue page.
Serial/Telnet User Interface Viewing SCSI Status Information To display SCSI status information, in the System Statistics Menu, choose 3) Display Parallel SCSI Protocol Status. The Parallel SCSI Protocol Status Menu is displayed. Figure 74 is an illustration of the SCSI Status Menu. Figure 74: SCSI Status menu SCSI Status Menu options: ■ 1) Display SCSI Statistics displays SCSI statistics. ■ 2) Display Attached SCSI Devices displays attached SCSI devices.
Serial/Telnet User Interface Figure 75 is an illustration of the SCSI Device Display Menu. Figure 75: SCSI Device Display menu SCSI Device Display Menu options: ■ 1) Issue discovery for all buses issues a discovery command for all SCSI buses. ■ 2) Issue discovery for selected bus issues a discovery command for the selected bus. ■ 3) Issue boot discovery issues a boot discovery command. ■ 4) Display all local devices displays a list of local devices for all buses.
Serial/Telnet User Interface Figure 76 is an illustration of the SCSI Resource Display page. Figure 76: SCSI Resource Display screen Event Log In the System Utilities Menu, 2) Event Log is used to view and clear the system Event Log. Figure 77 is an illustration of the Event Log Menu. Figure 77: Event Log menu Event Log Menu options: ■ 1) Display event log displays the Event Log. ■ 2) Clear event log deletes all entries from the Event Log.
Serial/Telnet User Interface Trace Dump Menu In the router Main Menu, 3) Display Trace and Assertion History is used to manage trace history information. Figure 78 is an illustration of the Trace Dump Menu. Figure 78: Trace Dump menu Trace Dump Menu options: ■ 1) Display trace for current boot cycle displays current boot cycle trace history information. ■ 2) Display trace from previous boot cycle displays previous boot cycle trace history information.
Serial/Telnet User Interface Note: Initially, the factory default router IP address is 1.1.1.1. To view the current IP address, navigate to the Ethernet Configuration Menu and view the screen display. See the “Configuration Menu” section for information on viewing and changing the router IP address. 4. Specify the directory location on the computer or network where the FTP program will store the trace file. 5. Enter the user name and password.
Serial/Telnet User Interface Reboot Option To reboot the router, in the Main Menu, select 4) Reboot. After this option is selected, a confirmation prompt is displayed. If a positive response is given to the confirmation message, the router is restarted. Note: Current router activities will be disrupted during a reboot. Download New Firmware Option To download a new version of the firmware: 1. Select 5) Download a New Revision of the Firmware in the router Main Menu. A confirmation prompt is displayed. 2.
Serial/Telnet User Interface Figure 79 is an illustration of the Download Firmware Menu after a new version of the firmware has been loaded.
Serial/Telnet User Interface 144 Network Storage Router e1200-160
5 FTP User Interface 5F The following tasks can be managed through an FTP interface: ■ Access the FTP User Interface (UI), page 146 ■ Backup and Restore Configuration Settings, page 146 ■ Copy Trace Buffers, page 149 ■ Upgrade Firmware, page 150 Each of these procedures is discussed in this chapter.
FTP User Interface Access the FTP User Interface (UI) To access the router using an FTP UI: 1. Connect the router to the Ethernet network used by the host computer. 2. Start an FTP session using the router IP address: ftp where IP address is the IP address of the router. The default router IP address is 1.1.1.1. Note: You may also need to specify the external directory location where your FTP utility will store the backup configuration file. 3. Enter the user name and password.
FTP User Interface Backing up the Router Configuration To backup the router configuration settings: 1. Connect the router to the Ethernet network used by the host computer. 2. Start an FTP session using the router IP address: ftp where IP address is the IP address of the router. The default router IP address is 1.1.1.1. Note: You will need to specify the external directory location where your FTP utility is to store the backup configuration file. 3. Enter the user name and password.
FTP User Interface Restoring the Router Configuration To restore a configuration to the router: 1. Connect the router to the Ethernet network used by the host computer. 2. Start an FTP session using the router IP address: ftp where IP address is the address of the router. The default IP address of the router is 1.1.1.1. 3. Enter the user name and password. The default user name is root and the default password is password.
FTP User Interface Copy Trace Buffers Use the following procedure to save copies of the trace buffers: 1. Connect the router to the Ethernet network used by the host computer. 2. Start an FTP session using the router IP address: ftp where IP address is the address of the router. The default router IP address is 1.1.1.1. Note: You will need to specify the directory location where your FTP utility will store the trace file. 3. Enter the user name and password.
FTP User Interface Upgrade Firmware Use the following procedure for Windows-based systems to upgrade the router firmware. Note: A JAVA applet-based FTP utility is also accessible from the UI. 1. Connect the router to the Ethernet network used by the host computer. 2. Start an FTP session using the router IP address: ftp where IP address is the IP address of the router. The default router IP address is 1.1.1.1. 3. Enter the user name and password.
Basic Troubleshooting 6 6F This chapter discusses some basic methods of identifying problems in the setup and configuration of the HP StorageWorks Network Storage Router. Most problems occur during the initial installation of the router. Before proceeding with advanced troubleshooting techniques, verify all connections and review the configuration.
Basic Troubleshooting ■ Introducing HP StorageWorks Library and Tape Tools, page 160 — Software Features — Finding Additional Information — Getting Support 152 Network Storage Router e1200-160
Basic Troubleshooting LED Indicators The LED indicators on the router are useful for diagnosing various problems: ■ The Fibre Channel port LEDs indicates Fibre Channel activity and link status. If one of these indicators does not light or stays continually lit without any corresponding SCSI bus activity, it may indicate a problem with the Fibre Channel link. Verify the Fibre Channel configuration. ■ The SCSI bus LEDs indicates SCSI activity.
Basic Troubleshooting Table 10: Router illustration components Item 154 Description 7 8 SCSI bus activity LED (on corresponding port) 9 SCSI VHDCI connector (2) SCSI bus activity LED (on corresponding port) Network Storage Router e1200-160
Basic Troubleshooting Basic Troubleshooting If possible, simplify the installation by reducing it to the most basic configuration. Then, add elements one at a time, verifying the operation after each step.
Basic Troubleshooting Verifying Fibre Channel Port Connection If SCSI devices are recognized on the SCSI buses, but do not appear to the Fibre Channel host, it may be that the Fibre Channel link is not properly established. Most hubs and switches have link indicators showing link status. When the router is connected and powered on, this link indicator should be solid. If it is not, check the cabling or connections.
Basic Troubleshooting Verifying SCSI Devices in Windows NT If running Fibre Channel-to-SCSI mapping mode, verify the Fibre Channel and the SCSI devices are recognized by the router. Sometimes Windows NT may need to be rebooted with all SCSI devices and the router powered up before recognizing the devices. To verify the Fibre Channel and SCSI devices: 1. Navigate to the Windows NT Control Panel, and select SCSI Adapters. 2. Double click the Fibre Channel HBA. The SCSI devices should be listed.
Basic Troubleshooting Verifying the Host Configuration In some cases, the Fibre Channel HBA or host device driver may not be working properly. Check the configuration of these elements. It may be useful to check the release notes for the device driver to see if there are any specific issues or a required configuration. It may also be useful to ensure that the current version of the HBA driver is being used.
Basic Troubleshooting Verifying PRLI Data The router returns the PRLI (preliminary login) response data as specified in Table 12. In the default configuration, the router returns PRLI Data (PRLI Accept Payload) with the Target bit SET and the Initiator bit CLEAR. However, some configurations require the Initiator bit be SET, such as in router-to-router configurations. See the Fibre Channel Overrides Menu for more information about changing the initiator bit.
Basic Troubleshooting Introducing HP StorageWorks Library and Tape Tools To provide continued service to our customers, HP provides the HP StorageWorks Library and Tape Tools (L&TT) software application. L&TT is a diagnostic tool that is designed to aid in the installation and maintenance of both HP tape devices and tape libraries. L&TT includes several features designed for use by both HP storage customers and trained service personnel.
Basic Troubleshooting ■ Firmware Upgrades-L&TT provides a convenient way of updating product firmware, enabling users with an Internet connection to take advantage of ongoing enhancements. The software can be configured to check the Web automatically for firmware updates for connected devices, or you can manually check the Web for updates if the automatic update feature is not desired. If updated firmware is available, the program notifies the user, and the updates can easily be copied to the system.
Basic Troubleshooting Finding Additional Information The HP website provides the current version of L&TT for download, and general information about the tool. Access the website at: http://www.hp.com/support/tapetools Getting Support E-mail support is available from ltt_team@hp.com. You should expect a response within 24 hours (usually sooner) during a normal business week.
Serial and Ethernet Pin Assignments A AF This appendix provides details for: ■ RJ-11 Serial Pin Assignments, page 164 ■ RJ-45 Ethernet Cable Pin Assignments, page 165 Network Storage Router e1200-160 163
Serial and Ethernet Pin Assignments RJ-11 Serial Pin Assignments The layout of the pin assignments for the serial receptacle on the router is illustrated in Figure 81. 6 Link/ Act 5 4 Fibre Channel 3 2 1 LVD/SE SCSl 0 Pwr. 1 Serial Ethernet Figure 81: RJ-11 Serial pin assignments The pin definitions listed in Table 13 correspond to the pin assignments in Figure 81.
Serial and Ethernet Pin Assignments RJ-45 Ethernet Cable Pin Assignments The layout of the pin assignments for RJ-45 Ethernet receptacle is illustrated in Figure 82. 1 Link/ Act 2 3 Fibre Channel Pwr. 4 5 6 7 8 LVD/SE SCSl 0 1 Serial Ethernet Figure 82: RJ-45 Ethernet pin assignments The pin definitions listed in Table 14 correspond to the pins assignments in Figure 82. The router Ethernet connection supports the IEEE specifications for 10BASE-T and 100BASE-TX Ethernet standards.
Serial and Ethernet Pin Assignments 166 Network Storage Router e1200-160
Controller LUN Commands B BF The HP StorageWorks Network Storage Router supports and executes the set of SCSI-3 commands listed in this Appendix. These commands can be received as FCP commands over the Fibre Channel bus and are supported by the Controller LUNs. This document refers to these commands as Controller LUN commands. Complete definitions of SCSI-3 commands can be found in the SCSI-3 standard available from the American National Standards Institute (ANSI).
Controller LUN Commands General Commands ■ Report LUNs ■ Inquiry Each of these commands is discussed in the following paragraphs. Report LUNs Command The Report LUNs command returns a list of LUNs that can receive commands. The format of the Report LUNs command is shown in Table 15.
Controller LUN Commands The router returns the LUN Parameters as defined in Table 16. Table 16: Report LUNs Data Bit/ Byte 7 6 5 4 3 2 0 Most Significant Byte (MSB) 1 LUNs Length List 1 0 2 3 Least Significant Byte (LSB) 4 Reserved 5 Reserved 6 Reserved 7 Reserved All LUNs are reported and will appear in the host map. Note: In addition to the device LUNs, controller LUNs are also included in the report. Controller LUN values are displayed at the end of the list.
Controller LUN Commands EVPD Page 0x80 If the EVPD bit (bit 0 of byte 1) is set and the Page Code is 0x80, the unit serial number page is returned. The format of this page is shown in Figure 18.
Controller LUN Commands Table 19: LUN Inquiry Data Item Value Vendor ID “HP” Product ID “router” Revision Level “XXXXXX” The router will only reply to a SCSI Inquiry using 8-byte LUN field of 0x00. Note: The Revision Level comes from the last four characters of the build string, which appears in the headings for most menu screens.
Controller LUN Commands 172 Network Storage Router e1200-160
Addressing Methods and Table Structures C CF Fibre Channel and SCSI systems use different methods of addressing devices. The router has a method of translating device IDs so each SCSI device is mapped to the appropriate Fibre Channel LUN. The SCSI buses establish the bus connections between devices. Targets on a SCSI bus may internally address LUNs. The addressing of a specific SCSI device is represented by the BUS:TARGET:LUN triplet.
Addressing Methods and Table Structures Table 20: Addressing Sequence Bit/Byte 7 6 5 4 Address Method N 3 2 1 0 Address Method Specific Address Method Specific N+1 Table 21: Address Method Definitions Code Description 00 Peripheral Device Addressing Method 01 Volume Set Addressing Method 10 Logical Unit Addressing Method 11 Reserved Table 22: SCSI Logical Unit Addressing Bit/Byte N 7 1 6 0 5 4 3 2 1 0 4 3 2 1 0 Target Table 23: Peripheral Device Addressing Bit/Byte N
Addressing Methods and Table Structures Depending on the configuration, the router supports the Peripheral Device Addressing method and the Logical Unit Addressing method. The data shown in Table 24 comes from the Fibre Channel Configuration Menu. The administrator enters the node number (number to the left of the colon in Table 24) and the router translates the node number into the corresponding AL_PA value (number to the right of the colon in Table 24).
Addressing Methods and Table Structures SCC (SCSI Controller Command) Addressing Method When a router is configured to use SCSI Controller Command addressing (SCC) and a command is received, the router either will respond as a controller device to the FCP Initiator or will route the FCP request to a specified BUS:TARGET:LUN.
Addressing Methods and Table Structures Indexed Addressing Method Indexed addressing allows for host bus adapter (HBA) drivers that use only Peripheral Device Addressing to access SCSI devices attached to the router. This addressing is done by use of a table, which is indexed by sequential LUN values, indicating the selected BUS:TARGET:LUN devices. In this mode, it is not possible to address the router as a controller unit directly.
Addressing Methods and Table Structures 178 Network Storage Router e1200-160
Regulatory Compliance Notices D DE Federal Communications Commission Notice Part 15 of the Federal Communications Commission (FCC) Rules and Regulations has established Radio Frequency (RF) emission limits to provide an interference-free radio frequency spectrum. Many electronic devices, including computers, generate RF energy incidental to their intended function and are, therefore, covered by these rules.
Regulatory Compliance Notices Class A Equipment This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Regulatory Compliance Notices Declaration of Conformity for Products Marked with the FCC Logo, United States Only This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Regulatory Compliance Notices Canadian Notice (Avis Canadien) Class A Equipment This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. Class B Equipment This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Regulatory Compliance Notices Japanese Notice Network Storage Router e1200-160 183
Regulatory Compliance Notices BSMI Notice Laser Device All HP systems equipped with a laser device comply with safety standards, including International Electrotechnical Commission (IEC) 825. With specific regard to the laser, the equipment complies with laser product performance standards set by government agencies as a Class 1 laser product. The product does not emit hazardous light; the beam is totally enclosed during all modes of customer operation and maintenance.
Regulatory Compliance Notices Compliance with International Regulations All HP systems equipped with laser devices comply with appropriate safety standards including IEC 825. Laser Product Label A label is located on the surface of the HP supplied laser device. Laser Information Table 26: Laser Information Feature Description Laser type Semiconductor GaAIAs Wave length 780 nm +/- 35 nm Divergence angle 53.5 degrees +/- 0.5 degrees Output power Less than 0.
Regulatory Compliance Notices 186 Network Storage Router e1200-160
Electrostatic Discharge E EF To avoid damaging equipment, be aware of the precautions you need to follow when setting up the system or handling parts. A discharge of static electricity from a finger or other conductor may damage system boards or other static-sensitive devices. This type of damage may reduce the life expectancy of the device. To prevent electrostatic damage, observe the following precautions: ■ Avoid hand contact by transporting and storing products in static-safe containers.
Electrostatic Discharge Grounding Methods There are several methods for grounding. Use one or more of the following methods when handling or installing electrostatic-sensitive parts: ■ Use a wrist strap connected by a ground cord to a grounded workstation or computer chassis. Wrist straps are flexible straps with a minimum of 1 megohm ± 10 percent resistance in the ground cords. To provide proper ground, wear the strap snug against the skin.
index A C Active Fabric configuration Serial/Telnet UI 128 Visual Manager UI 50 addressing, defined 173 audience 10 authorized reseller, HP 15 auto-assigned addressing described 176 auto-assigned maps, defined 32 Center for Devices and Radiological Health See CDRH clock configuration Serial/Telnet UI 127 Visual Manager UI 52 configuration settings backing up 147 common 29 restoring 148 troubleshooting 157 configurations, Fibre Channel to SCSI, illustrated 20 controller LUN commands general commands, lis
Index Serial/Telnet UI 127 Visual Manager UI 52 DB-9 pin assignments 164 DB-9 pin layout 164 DB-9 serial pin assignments, illustrated 164 default settings, Ethernet 26 default settings, router 26 devices supported 20 troubleshooting 157 DHCP setup Serial/Telnet UI 100 Visual Manager UI 49 discovery mode Fibre Channel Serial/Telnet UI 102 Visual Manager UI 57 overview of 30 SCSI Serial/Telnet UI 106 Visual Manager UI 61 document conventions 11 prerequisites 10 related documentation 10 E environmental requi
Index deleting entries Serial/Telnet UI 118 Visual Manager UI 69 editing entries Serial/Telnet UI 112 Visual Manager 69 filling entries Serial/Telnet UI 118 Visual Manager UI 69 removing gaps in Serial/Telnet UI 117 Visual Manager UI 69 viewing and changing Serial/Telnet UI 110 Visual Manager UI 69 Fibre Channel port buffered tape writes Serial/Telnet UI 103 Visual Manager UI 58 configuration Serial/Telnet UI 101 Visual Manager UI 56 Configuration screen, illustrated 56 default map Serial/Telnet UI 103 Vis
Index HP authorized reseller 15 storage website 14 technical support 14 I I/O configuration Visual Manager UI 54 indexed addressing described 177 indexed maps, defined 32 initiator IDs, SCSI Serial/Telnet UI 106 Visual Manager UI 60 interfaces user, listed 27 internal termination, SCSI Visual Manager UI 61 IP address Serial/Telnet UI 99 Visual Manager UI 49 IP gateway Serial/Telnet UI 99 Visual Manager UI 49 L LAN-free backup and restore, illustrated 23 laser device product classification label 185 radia
Index deleting (removing) the current map Visual Manager UI 67 deleting a host from the host list Serial/Telnet UI 121 Visual Manager UI 66 displaying the entire device list Serial/Telnet UI 123 editing entries Serial/Telnet UI 112 editing host information Serial/Telnet UI 121 editing the current map Serial/Telnet UI 111 editing the host list of the current map Serial/Telnet UI 118 overview of Visual Manager UI 65 selecting a host for the current map Serial/Telnet UI 120 Visual Manager UI 66 selecting the
Index port configuration Serial/Telnet UI 101 port mode, Fibre Channel Serial/Telnet UI 103 Visual Manager UI 57 port name, Fibre Channel Serial/Telnet UI 102 Visual Manager UI 56 power requirements, of router 24 power supply LED indicators 19 power-up messages, illustrated 94 prerequisites 10 PRLI data, troubleshooting 159 process, converting Fibre Channel to SCSI, illustrated 21 process, converting SCSI to Fibre Channel, illustrated 22 R rack stability, warning 13 rebooting Serial/Telnet UI 142 Visual M
Index Serial/Telnet UI 116 Visual Manager UI 73 deleting entries Serial/Telnet UI 118 Visual Manager UI 73 editing entries Serial/Telnet UI 112 Visual Manager 72 filling entries Serial/Telnet UI 118 Visual Manager UI 73 removing gaps in Serial/Telnet UI 117 Visual Manager UI 73 viewing and changing Serial/Telnet UI 110 Visual Manager UI 72 SCSI to Fibre Channel conversion process, illustrated 22 security configuration Serial/Telnet UI 100 Visual Manager UI 51 serial port configuration, troubleshooting of 9
Index editing the host list of the current map, edit options, listed 119 initial access 108 listed 109 screen navigation 109 selecting the current map 109 selecting the host for the current map 120 viewing the current map 110 mapping tasks,SCSI adding entries 115 creating map entries 116 deleting entries 118 filling entries 118 removing gaps in 117 overview of the UI 27 port configuration 101 reboot option, described 142 Reset and Save Configuration to Factory defaults option, described 129 Restore Last Sa
Index Serial/Telnet UI Fibre Channel Transport Queues page, illustrated 136 Serial/Telnet UI host list display for Fibre Channel maps, illustrated 119 Serial/Telnet UI host list display for SCSI maps, illustrated 119 Serial/Telnet UI RealTime Clock Configuration Menu, described 127 Serial/Telnet UI SCSI bus configuration menu, illustrated 105 Serial/Telnet UI SCSI Current Map display, illustrated 111 Serial/Telnet UI SCSI Device Display Menu, illustrated 138 Serial/Telnet UI SCSI Resource Display screen, i
Index Serial/Telnet UI 142 user configuration Serial/Telnet UI 100 Visual Manager UI 51 user interfaces, listed 27 utilities configuration Serial/Telnet UI 130 Visual Manager UI 75 V Visual Manager Clear Current Trace Buffer screen, illustrated 82 Visual Manager Current traces screen, illustrated 81 Visual Manager Discovery screen, illustrated 64 Visual Manager Ethernet Configuration dialog box, illustrated 48 Visual Manager Event Log settings screen, illustrated 83 Visual Manager FTP Utility screen, illu
Index deleting entries 69 filling maps 69 removing gaps in 69 viewing and changing 69 mapping tasks, Fibre Channel and SCSI adding a new map 67 deleting a host 66 deleting a map 67 selecting a host 66 selecting a map 67 mapping tasks, SCSI adding entries 73 clearing map entries 73 creating entries 73 deleting entries 73 filling maps 73 removing gaps in 73 viewing and changing 72 network configuration 47 Network Menu options, listed 47 overview of the UI 27 reboot option 87 report options 86 resetting to fa
Index 200 Network Storage Router e1200-160