Installation Guide for 100VG Recessed Transceivers 1995-11

ManualsBrandsHP ManualsComputer AccessoriesHP AdvanceStack 100-Base FX Xcvr Module

HP 100VG Recessed Transceivers

Installation Guide

Introduction

The HP 100VG Recessed Transceivers are used to provide connection to

various network media for the HP J2981A 100VG Module and other

HP networking devices that are designed to accept these transceivers. The

transceivers are installed into the 100VG Xcvr Slot of the HP networking

device or device module.

This document describes how to install, verify, and troubleshoot the

following three transceivers:

Note:

The illustrations in this document show the above listed units being used

with the HP J2981A 100VG Module. The procedures described in this

document also pertain to using these units in other HP networking devices

that are designed to accept them.

HP J3028A Recessed 100VG Twisted-Pair Transceiver

HP J3027A Recessed 100VG Fiber-Optic Multimode ST Transceiver

HP J3030A Recessed 100VG Shielded Twisted-Pair Transceiver

Summary of content (8 pages)

PAGE 1
HP 100VG Recessed Transceivers Installation Guide Introduction The HP 100VG Recessed Transceivers are used to provide connection to various network media for the HP J2981A 100VG Module and other HP networking devices that are designed to accept these transceivers. The transceivers are installed into the 100VG Xcvr Slot of the HP networking device or device module.
PAGE 2
Installation Steps Warning: Turn off power to the device that will accept the transceiver. The steps to install the HP 100VG Recessed Transceivers are: 1. Insert the transceiver into an HP networking device’s 100VG Xcvr slot. 2. Connect the network cables to the transceiver. 3. Apply power to the HP networking device or device module into which the transceiver is installed, and check the transceiver for correct operation. Details on these steps are provided in the rest of this document.
PAGE 3
1. Insert the transceiver into the slot. The transceivers are installed into an HP networking device in an identical manner, as follows: 1. Remove AC power from the HP networking device or device module; then, using a flat-bladed or Torx T-10 screwdriver, unscrew the two retaining screws on the existing transceiver, or 100VG Xcvr cover plate, and remove it from the HP networking device or device module. Loosen the captured screws on a 100VG Xcvr cover plate. 2.
PAGE 4
HP J3028A Recessed 100VG Twisted-Pair Transceiver The HP J3028A Recessed 100VG Twisted-Pair Transceiver connects an HP networking device to an unshielded twisted-pair (UTP) network. This transceiver is compatible with IEEE 802.12 standard. Connecting the Twisted-Pair Cable An HP 100VG LAN supports category 3, 4, and 5 four-pair, 100 ohm UTP (unshielded twisted-pair) cables. Category 3 UTP cable is standard, voice-grade, telephone cable. If you have a twisted-pair cable that complies with Ethernet/IEEE 802.
PAGE 5
HP J3027A Recessed Fiber-Optic Multimode ST Transceiver The HP J3027A Recessed Fiber-Optic Multimode ST Transceiver connects an HP networking device to a fiber-optic network. This transceiver is compatible with the IEEE 802.12 and its wavelength is 1300nm. Optical fibers conforming to the ISO/IEC DIS 11801 standard will work with this transceiver. Connecting the Fiber-Optic Cable Important: Fiber-optic cables have two separate fibers for delivery of data to and from the transceiver.
PAGE 6
HP J3030A Recessed 100VG Shielded Twisted-Pair Transceiver The HP J3030A Recessed 100VG Twisted-Pair Transceiver connects an HP networking device to a shielded twisted-pair (STP) network. This transceiver is compatible with IEEE 802.12. Connecting the Shielded Twisted-Pair Cable An HP 100VG LAN supports cable type 1 and 2 of shielded twisted-pair cable. Maximum cable length is 100 meters. Push the shielded twisted-pair cable into the transceiver.
PAGE 7
Specifications Physical Dimensions All Transceivers Width 4.14 cm (1.63 in) Depth 9.22 cm (3.63 in) Height 2.36 cm (.93 in) Weight 50 g Environmental Operating temperature: Nonoperating temperature: Relative humidity: Maximum altitude: 0°C to 55°C (32°F to 131°F) -40°C to 70°C (-40°F to 158°F) 15% to 95% at 40°C (104°F) non-condensing 4.
PAGE 8
Technical information in this document is subject to change without notice. All rights reserved. Reproduction, adaptation, or translation without prior written permission is prohibited except as allowed under the copyright laws. © 1995 Hewlett-Packard Company HP Part Number: 5963-6533 Edition 1, November 1995 Printed in U.S.A.