Safety and Regulatory Information, HP Integrity BL860c, BL870c, BL860c i2, BL870c i2, and BL890c i2 Server Blades, Regulatory Model Numbers: RSVLA-0502, RSVLA-BC21, RSVLA-BC11 HP Part Number: 5992-1071 Published: August 2011 Edition: 2
© Copyright 2011 Hewlett-Packard Development Company, L.P. Legal Notices The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. Microsoft and Windows are U.S.
1 Safety and Regulatory Information Overview Regulatory Compliance statements are required by some countries or regions for international importation of HP servers.
Product Environmental Information See the following links for environmental and safety information for HP products and for HP environmental initiatives: • www.hp.com/go/ecodata HP product environmental and safety information and compliance data including RoHS and REACH. • www.hp.com/environment HP environmental information including company programs, product recycling, and energy efficiency.
Electrostatic Discharge (ESD) Precautions When handling any electronic component or assembly (such as a PCI card or memory DIMM), you must observe the following antistatic precautions to prevent damage. An ESD kit (HP P/N A3024-80004) is available (or supplied with memory additions). This kit contains one wrist strap, one conductive sheet, and one antistatic foam pad. • Always disconnect power from the server and wear a grounded wrist strap when working around the server.
Cabinet Safety Precautions WARNING! Cabinets are heavy even when empty. Exercise caution when moving cabinets whether equipment is installed in the cabinet or not. Avoid rolling cabinets on rough or uneven surfaces or inclines greater than 10 degrees. Unloading cabinets from the pallet and movement of cabinets should be performed by at least two people. Slideable products are not to be extended from the cabinet while the equipment is on the shipping pallet.
NOTE: Replace all battery modules at the same time. UPS battery replacement overview The battery modules are hot swappable and can be replaced without powering down the UPS. To power down the UPS, see the UPS user guide for instructions. CAUTION: When hot-swapping batteries, the load is not protected in the event of a utility power failure, unless at least one ERM is installed. IMPORTANT: Charge the batteries before supplying backup power to devices. See the UPS user guide for recommended charging times.
5. Disconnect the black battery lead. HP UPS R1500 1. 2. 3. 4. Remove the UPS front bezel. Disconnect the battery leads. Remove the UPS battery bracket. Carefully pull the battery leads through the hole in the battery bracket. Remove the UPS battery modules. IMPORTANT: Do not pull the battery leads when removing or installing the batteries. HP UPS R3000 1. 2. 3. 8 Remove the UPS front bezel. Disconnect the battery leads. Remove the UPS battery bracket.
4. Remove the UPS battery modules. HP UPS R/T3000 WARNING! To prevent personal injury from electric shock or damage to the equipment, remove the battery lead labels, and verify that the ERM circuit breakers are in the Off position. 1. 2. 3. 4. Remove the UPS front bezel. Disconnect the battery leads. Remove the UPS battery bracket. Remove the UPS battery modules. IMPORTANT: Do not pull the battery leads when removing or installing the batteries. HP UPS R5000 1. 2. Remove the UPS front bezel.
3. 10 Remove the UPS battery bracket.
4. Remove the UPS battery modules. IMPORTANT: Do not pull the battery leads when removing or installing the batteries. HP UPS R5500 1. 2. 3. Remove the UPS front bezel. Remove the UPS battery bracket. Remove the UPS battery modules. HP UPS R7000 1. 2. Remove the UPS front bezel. Disconnect the battery leads.
3. 12 Remove the UPS battery bracket.
4. Remove the UPS battery modules. IMPORTANT: Do not pull the battery leads when removing or installing the batteries. HP 3 Phase UPS R8000/3 and R12000/3 1. 2. 3. Remove the UPS front bezel. Remove the UPS battery bracket. Remove the UPS battery modules.
Battery replacement notice WARNING! Power products contain sealed lead-acid battery modules. A risk of fire and burns exists if the battery is not properly handled. To reduce the risk of personal injury: • Do not attempt to recharge the battery. • Do not expose the battery to temperatures higher than 60°C (140°F). • Do not disassemble, crush, puncture, short external contacts, or dispose of in fire or water. The battery might explode.
Also see the following: http://www.hp.com/hpinfo/globalcitizenship/environment/productdata/disassemblyservers.html Perchlorate Material - Special Handling May Apply See http://www.dtsc.ca.gov/hazardouswaste/perchlorate. This product may include a real-time clock battery or coin cell battery that may contain perchlorate and may require special handling when recycled or disposed of in California.
Additional information about this product may be obtained at the following url: http://www.hp.com/go/chinarohs European Union RFI Statement This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. USA Radio Frequency Interference FCC Notice The Federal Communications Commission (in 47 CFR Part 15 subpart B) has specified that the following notice be brought to the attention of the users of this product.
Australia C-Tick Label Figure 1 Australian C-Tick Label Overview 17
Taiwan BSMI This product is fully compliant to CNS 13438 (CISPR 22: 1993) Class A. Warning Users: This is a Class A IT (Information Technology) product. If this product is used in a domestic environment, radio frequency disturbance may occur, in which case the user may be required to take corrective actions.
Declarations of Conformity Overview 19
Safety and Regulatory Information
Overview 21
*5992-1071* Printed in the US
