HP BladeSystem c3000 Tower Enclosure Setup and Installation Guide Part Number 457022-002 August 2008 (Second Edition)
© Copyright 2007, 2008 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. Microsoft, Windows, and Windows Server are U.S.
Contents Planning the installation................................................................................................................. 5 Pallet contents ........................................................................................................................................... 5 Installation environment requirements ........................................................................................................... 6 Warning, caution, and important messages...............
Blade or Port Info screen ................................................................................................................ 56 Turn Enclosure UID On/Off screen................................................................................................... 57 View User Note screen................................................................................................................... 59 Chat Mode screen ..............................................................................
Planning the installation Pallet contents Item Name Description 1 HP BladeSystem c3000 Tower Enclosure The HP BladeSystem tower enclosure 2 Device bay blank A mandatory insert installed in any unused device bay 3 Power supply blank A mandatory insert installed in any unused power supply bay 4 Power supply (quantity as ordered) The power supply for the enclosure 5 Half-height device (quantity as ordered) A half-height server or storage blade 6 Full-height device (quantity as ordered) A f
Item Name Description 9 HP Active Cool fan (quantity as ordered) A fan used to cool the components installed in the enclosure 10 Enclosure/Onboard Administrator link module The module used to provide enclosure-link connectivity and Onboard Administrator/iLO/interconnect management access 11 Module blank A mandatory cover installed in the reserved module bay 12 HP BladeSystem Insight Display A display that provides information about the health and operation of the enclosure 13 Interconnect mo
WARNING: To reduce the risk of personal injury or damage to the equipment in a rack-free environment: • Never stack an enclosure on top of another enclosure. • Never place equipment on top of an enclosure. • Never place an enclosure on a surface that cannot support up to 153.7 kg (338.9 lb). Warning, caution, and important messages WARNING: To reduce the risk of personal injury or damage to equipment, heed all warnings and cautions throughout the installation instructions.
WARNING: A risk of electric shock from high leakage current exists. Before connecting the AC supply to the power enclosures, be sure that the electrical outlets are properly grounded (earthed). The area where the enclosure is installed should be designated as a restricted access area, and the enclosure is intended to be used with a dedicated uninterruptible power supply (UPS) that uses an industrial style wall plug to insure a reliable protective earth ground connection.
If the enclosure is not completely filled with components, the remaining gaps between the components can cause changes in the airflow, which can adversely affect cooling within the enclosure. Fill these gaps with blanks. CAUTION: Always use blanks to fill empty spaces in enclosures. This arrangement ensures proper airflow. Using an enclosure without the proper blanks results in improper cooling that can lead to thermal damage.
Furthermore, you must be sure that all power distribution devices used in the installation, such as branch wiring and receptacles, are listed or certified grounding-type devices. Because of the high ground-leakage currents associated with this equipment, HP recommends the use of a PDU that is either permanently wired to the building’s branch circuit or includes a nondetachable cord that is wired to an industrial-style plug.
Identifying components and LEDs Enclosure front components Item Description 1 Device bays ("Device bay numbering" on page 11) 2 CD/DVD-ROM drive blank or CD/DVD-ROM drive (optional) 3 Onboard Administrator tray (reserved for future use) 4 Insight Display 5 Onboard Administrator tray containing Onboard Administrator 1 Device bay numbering Each enclosure requires interconnects to provide network access for data transfer. Interconnects reside in bays located on the rear of the enclosure.
Full-height device bay numbering Half-height device bay numbering Identifying components and LEDs 12
HP BladeSystem Insight Display components Item Description Function 1 Insight Display screen Displays Main Menu error messages and instructions 2 Up arrow button Moves the menu selection up one position 3 Down arrow button Moves the menu selection down one position 4 OK button Accepts the highlighted selection and navigates to the selected menu 5 Left arrow button Moves the menu or navigation bar selection left one position 6 Right arrow button Moves the menu or navigation bar selection
Item Description Status 1 Reset button — 2 USB connector — 3 Health LED Green = Normal Red = OA firmware issue. See the HP Onboard Administrator User Guide on the HP website (http://www.hp.com/go/bladesystem/docum entation).
Item Description 10 Interconnect bay 4 11 Interconnect bay 3 Fan bay numbering Fan LEDs LED color Fan status Solid green The fan is working. Solid amber The fan has failed. Flashing amber See the Insight Display screen.
Power supply bay numbering Power supply LED Power LED (green) Failure LED (amber) Status Off Off No AC power to power supply units On Off AC present. Standby output on.
Interconnect bay numbering To support network connections for specific signals, install the interconnect module in the appropriate bay.
Installing components Setting up the enclosure 1. Select the proper location for the enclosure to be set up based on requirements detailed in "Planning the installation (on page 5)." 2. Remove the packing materials from the pallet. WARNING: To reduce the risk of personal injury or damage to the equipment in a rack-free environment: • Never stack an enclosure on top of another enclosure. • Never place equipment on top of an enclosure. • Never place an enclosure on a surface that cannot support up to 153.
Installing a power supply 1. Slide the power supply into the power supply bay until the device locks into place. Repeat this step for each required power supply. NOTE: When installing a power supply in power supply bay 1, 2, or 3, orient the power supply so the plug is positioned toward the bottom of the bay. When installing a power supply in power supply bay 4, 5, or 6, orient the power supply so the plug is positioned toward the top of the bay. See "Power supply bay numbering (on page 16)." 2.
Installing a full-height blade The enclosure ships with device bay shelves to support half-height devices. To install a full-height device, remove the device bay shelf and the corresponding blanks. To install a full-height blade: 1. Remove the blank. 2. Remove the three adjacent blanks. 3. Remove the device bay shelf ("Removing the device bay dividers" on page 22). 4. Remove the connector covers.
5. Prepare the blade for installation. 6. Install the blade in the empty bay. NOTE: If you plan to install four HP Active Cool Fans, you can install up to two full-height blades. Populate device bay 1 first, then populate device bay 2. If you plan to install six HP Active Cool Fans, blades can be installed in any configuration. For more information, see "Installing fans" and "Full-height device bay numbering (on page 12).
Removing the device bay dividers 1. Remove the blank.
2.
3. For the half-height divider, push the divider toward the back of the enclosure until the divider stops. Push the divider up to disengage the tabs from the divider wall, and then rotate the divider clockwise. For the mini divider, push the divider toward the back of the enclosure, and then slide it to the left. Pull the divider out of the chassis. 4. Remove the device bay divider from the enclosure. Creating a full-height device bay blank 1.
2. Fit the coupler plate in to the slots on top of the blank, and slide the coupler plate back until it snaps into place. 3. Fit the slots on the bottom of the second blank on to the tabs on the coupler plate, and slide the second blank forward until it snaps in place. 4. Install the full-height blank in to the device bay.
Installing a half-height blade 1. Remove the blank. 2. Install the device bay shelf, if applicable ("Installing dividers" on page 27). 3. Install the blade in the empty bay. NOTE: If you plan to install four HP Active Cool Fans, you can install up to four half-height blades. Populate the device bays in the following order: 1, 2, 5, 6. If you plan to install six HP Active Cool Fans, blades can be installed in any configuration.
Installing dividers You must install dividers to support half-height devices. The half-height divider adds support for four adjacent half-height devices. The mini divider adds support for two half-height and one full-height adjacent devices. 1. Remove the full-height blade, storage blade, or device bay blank. 2. Install the mini divider (proceed to step 3 to install the half-height divider): a.
c. 3. Slide the mini divider locking tab up to lock it. Install the half-height divider: a. Slide the half-height divider locking tab down. b. Align the three tabs on the left edge of the half-height divider with the openings in the enclosure, and then rotate the half-height divider counter-clockwise. CAUTION: Be sure that all five tabs (three on the left edge of the divider and two on the right edge of the divider) are fully inserted before sliding the divider forward to complete the installation.
c. Pull the half-height divider forward until it stops and slide the half-height divider locking tab up to lock it. Installing fans NOTE: The HP BladeSystem c3000 Tower Enclosure is shipped with four HP Active Cool fans and supports up to six fans. Install fans based on the number of blades installed: • For one to four half-height blades or one to two full-height blades, install four fans in bays 2, 4, 5, and 6. • For additional blades, install six fans using all bays.
NOTE: When installing a fan in the left column of fan bays, orient the fan so that the LED is in the upper right corner of the fan housing. When installing a fan in the right column of fan bays, orient the fan so the LED is in the lower left corner of the fan housing. To remove a fan, turn handle the counterclockwise to the unlock position, and pull the fan out of the enclosure.
To install a c3000 KVM module: 1. Press the tab, and then pull the KVM module blank from the enclosure. 2. Slide the c3000 KVM module into the bay. When fully inserted, the device locks into place. Attaching components to the c3000 KVM module For local access to the enclosure: 1. Connect a monitor to the video connector on the c3000 KVM module.
2. Connect a USB keyboard and mouse to the USB connectors on the c3000 KVM module. The USB connectors are interchangeable. To connect the c3000 KVM module to an HP Server Console Switch or an HP IP Console Switch: 1. Connect the optional USB interface adapter to the video connector and to one of the USB connectors on the c3000 KVM module. 2. Connect the CAT5 end of the KVM Interface adapter to an optional HP Console Switch. Removing the c3000 KVM module 1.
2. Press the tab, and then pull the c3000 KVM module from the enclosure. 3. Install a blank in an unused KVM module bay. When fully inserted, the device locks into place. Installing interconnect modules There are four single-wide interconnect bays in the enclosure. Interconnect bay 1 is reserved for a gigabit Ethernet switch or pass-through. Installation into the remaining interconnect bays depends on the type and location of the mezzanine card installed in the blade.
To install an interconnect module: 1. Remove the interconnect blank. 2. If you are installing a double-wide interconnect module, remove the interconnect bay dividers ("Removing interconnect bay dividers" on page 40). 3. Install the interconnect module in the enclosure. Mapping to interconnect ports Several port types are referenced in the following tables. • Examples of 1x ports are 1-Gb Ethernet (1 GbE) switch modules and Fibre Channel interconnect modules.
Mapping half-height blades The following table lists the available configurations for half-height devices installed in device bay N (1–8) Connection Port number Connects to interconnect bay/port Comments Embedded NIC NIC 1 1/Port N NIC 2 1/Port N+8 One single-wide Ethernet interconnect module 1x/2x port 1 2/Port N • 1x/2x port 2 2/Port N+8 One single-wide interconnect module • Only two ports will be connected. • Four port cards will only connect the first two ports.
Connection Port number Connects to interconnect bay/port Comments Mezzanine slot 2—1x or 2x cards 1x/2x port 1 3/Port N 1x/2x port 2 4 Port N One or two single-wide interconnect modules 1x/2x port 3 3/Port N+8 1x/2x port 4 4/Port N+8 4x port 1 3/Port N 4x port 2 3/Port N+8 Mezzanine slot 2—4x cards One double-wide interconnect module Mapping full-height blades The following table lists the available configurations for full-height devices installed in device bay N (1–4) Installing compo
Connection Port number Connect to interconnect bay/port Comments Embedded NIC NIC 1 1/Port N+4 NIC 2 1/Port N+12 One single-wide Ethernet interconnect module NIC 3 1/Port N NIC 4 1/Port N+8 Mezzanine slot 1—1x or 1x/2x port 1 2x cards (4x cards are not 1x/2x port 2 supported in this slot) 1x/2x port 3 2/Port N 2/Port N+8 2/Port N+4 1x/2x port 4 2/Port N+12 1x/2x port 1 3/Port N 1x/2x port 2 4/Port N 1x/2x port 3 3/Port N+8 1x/2x port 4 4/Port N+8 Mezzanine slot 2—4x cards 4x port
Mapping BL2x220c blades To support network connections for specific signals, install an interconnect module in the bay corresponding to the embedded NIC or mezzanine signals.
Connection Port number Connects to interconnect Comments bay/port Mezzanine slot 1— 1x, 2x, or 4x cards Server A: Mezz port 1 3/Port N Server A: Mezz port 2 4/Port N Server B: Mezz port 1 3/Port N+8 Server B: Mezz port 2 4/Port N+8 • Two single-wide modules or one doublewide interconnect module • Only two ports will be connected. • Four port cards will only connect the first two ports.
Interconnect bay crosslinks Interconnect bay crosslinks are wired between adjacent interconnect bay pairs. You can enable these crosslinks to provide module-to-module connections. The Onboard Administrator disables the interconnect bay crosslinks in instances where the crosslinks cannot be used, such as when two different modules reside in adjacent horizontal interconnect bays. Removing interconnect bay dividers The enclosure ships with interconnect bay dividers installed.
To reinstall an interconnect bay divider, align the interconnect bay divider with the rail, and slide the divider into the enclosure until it locks into place. Installing the enclosure/Onboard Administrator link module 1. Slide the enclosure/Onboard Administrator link module into the bay until the device locks into place.
Numerous configurations are possible. This section offers two possible configurations. Accessing a server blade with local KVM For this configuration, a USB hub is not necessary. To connect additional devices, use a USB hub. CAUTION: Before disconnecting the SUV cable from the connector, always squeeze the release buttons on the sides of the connector. Failure to do so can result in damage to the equipment. 1. Connect the SUV cable to the blade. 2. Connect the video connector to a monitor. 3.
o USB CD/DVD-ROM drive o USB keyboard o USB mouse o USB diskette drive NOTE: Use a USB hub when connecting a USB diskette drive and/or USB CD-ROM drive to the blade. The USB hub provides additional connections. NOTE: The Onboard Administrator with version 2.0 or greater firmware supports attaching a CD or DVD to any or all iLOs using the optional enclosure DVD drive or an external HP DVD drive for operating system installation or software updates.
Cabling and powering up the enclosure Cabling the enclosure After all system hardware is installed, cable the components. See the HP ProLiant BL System Best Practices Guide on the Documentation CD or the HP website (http://www.hp.com) for HP recommendations on cable ordering.
Item Connector Description 1 Enclosure linkdown port Connects to the enclosure link-up port on the enclosure beneath it using a CAT5 patch cable. 2 Enclosure link-up Connects to the enclosure link-down port on the enclosure above it using CAT5 port and service patch cable. On a stand-alone enclosure or the top enclosure in a series of linked port enclosures, the top enclosure link-up port may function as a service port. 3 OA1/iLO Onboard Administrator Ethernet connection.
NOTE: Total VA load of the attached enclosures should not exceed the VA capacity of the PDU. Do not exceed the rated current on circuit breakers. To connect power to the PDU: 1. Connect the power cables to the power supplies. 2. Connect the AC power cables to the installed PDU. 3. Continue powering up the enclosure. Powering up the enclosure WARNING: Be sure that all circuit breakers are locked in the off position before connecting any power components. 1.
Using the HP BladeSystem Insight Display Insight Display overview The Insight Display enables the rack technician to configure the enclosure initially. It also provides information about the health and operation of the enclosure. See the HP BladeSystem Onboard Administrator User Guide for additional information. The Insight Display background color varies with the condition of the enclosure health: • Blue—The Insight Display background illuminates blue when the enclosure UID is active.
To identify the enclosure, the rear enclosure UID light and the background of the Insight Display are illuminated blue when the enclosure is powered on initially. The Installation Wizard automatically turns on the enclosure UID at the beginning of the installation and turns it off after the installation is complete. The Enclosure Settings screen (on page 55) is the first screen to display. The background color is blue because the enclosure UID is active when this screen displays. 1.
o None Power Limit—The default setting is Not Set. The Power Limit Watts AC setting can be changed in increments of 50 Watts. IMPORTANT: When calculating the Power Limit Watts AC value, derate the circuit to 80% of the maximum to prevent tripping the circuit breaker (United States only). IMPORTANT: If your facility cannot support the calculated peak Watts AC, set the Power Watts AC value to match the capability of your facility. Dynamic Power—The default setting is Enabled.
DVD Drive—The default setting is Detached on all blades. To connect any blade to a CD or DVD disk inserted into the enclosure DVD that is plugged into the Onboard Administrator or included in the enclosure, navigate to Connect and press OK. The following selections are valid on the DVD Connection Settings menu: o Detach/Attach—Each server can be individually attached to or detached from the enclosure DVD drive by navigating to that bay and pressing the OK button.
o Yes—Copy the configured power settings, rack name, and LCD Lockout PIN (if set) from the Enclosure Settings screen to the detected enclosures. o No—Continue configuring the current enclosure only. The Insight Display installation wizard must be run on each of the other detected enclosures. Select this option if each enclosure requires different power settings.
9. If no errors are detected, the rear enclosure UID turns off, and the Insight Display screen illuminates green. Press the OK button to return to the Main Menu. Enclosure and blade hardware setup and configuration is complete. If errors are detected, the Insight Display screen illuminates amber, and the Health Summary screen displays. See Insight Display errors (on page 62) for more information on troubleshooting configuration and installation errors.
2. Pull the Insight Display out of the chassis to lock it into place, then tilt it for viewing. Navigating the Insight Display Navigate through the menus and selections by using the arrow buttons on the Insight Display panel ("HP BladeSystem Insight Display components" on page 13). Use the arrow buttons to move the selection box to a menu item, and then press the OK button to go to selected screen.
• Chat Mode ("Chat Mode screen" on page 59) TIP: Within any menu option, navigate the cursor to What is This, and press the OK button to view additional information about each setting, option, or alert.
Select View Alert and press the OK button to display the errors. Select Details to view the details of the error.
• Current enclosure ambient temperature • Current AC input power to the enclosure • Enclosure name • Rack name Blade or Port Info screen The Blade or Port Info screen displays information about a specific blade. On the first screen, select the blade number, then press the OK button. Select Blade Info or Port Info, and press the OK button.
To view information about the blade, select Blade Info and press the OK button. To view the ports used by a specific blade, select Port Info and press the OK button. On the full-height blade shown below, there are two embedded NICs. The other interconnect bays are empty. The two embedded NICs are connected to particular port numbers on the interconnect modules.
Selecting Turn Enclosure UID On from the main menu turns on the rear enclosure UID LED and changes the color of the Insight Display screen to blue. Selecting Turn Enclosure UID Off from the main menu turns off the rear enclosure UID LED and changes the color of the Insight Display screen to the current condition ("Insight Display overview" on page 47).
View User Note screen The View User Note screen displays six lines of text, each containing a maximum of 16 characters. Use this screen to display helpful information such as contact phone numbers or other important information. Change this screen using the remote Onboard Administrator user web interface. Both the background bitmap and the text can be changed.
Troubleshooting Troubleshooting resources The HP ProLiant Servers Troubleshooting Guide provides procedures for resolving common problems and comprehensive courses of action for fault isolation and identification, error message interpretation, issue resolution, and software maintenance on ProLiant servers and server blades. This guide includes problemspecific flowcharts to help you navigate complex troubleshooting processes. To view the guide, select a language: • English (http://www.hp.
This symbol indicates the presence of electric shock hazards. The area contains no user or field serviceable parts. Do not open for any reason. WARNING: To reduce the risk of injury from electric shock hazards, do not open this enclosure. This symbol on an RJ-45 receptacle indicates a network interface connection. WARNING: To reduce the risk of electric shock, fire, or damage to the equipment, do not plug telephone or telecommunications connectors into this receptacle.
85.5 188.4 WARNING: To reduce the risk of personal injury or damage to the equipment, observe local occupation health and safety requirements and guidelines for manual handling, and obtain adequate assistance to lift and stabilize the chassis during installation or removal. CAUTION: To properly ventilate the system, you must provide at least 7.6 cm (3.0 in) of clearance at the front and back of the server. CAUTION: The server is designed to be electrically grounded (earthed).
Cooling errors Cooling errors occur when too few fans are installed in the enclosure or when the existing fans are not installed in an effective configuration. Cooling errors can occur on blades, storage blades, or interconnect modules. To correct a cooling error: 1. Use the arrow buttons to navigate to Fix This, and press OK. 2. Review and complete the corrective action suggested by the Insight Display.
• Fans • AC power inputs To correct a device failure error: 1. Use the arrow buttons to navigate to Fix This, and press OK. 2. Review and complete the corrective action suggested by the Insight Display. In most cases, you must remove the failed component to clear the error. 3. Replace the failed component with a spare, if applicable. NOTE: If the device failure error is an AC power input failure error, you must have the failed AC input repaired to clear the error.
Technical support Before you contact HP Be sure to have the following information available before you call HP: • Technical support registration number (if applicable) • Product serial number • Product model name and number • Product identification number • Applicable error messages • Add-on boards or hardware • Third-party hardware or software • Operating system type and revision level HP contact information For the name of the nearest HP authorized reseller: • See the Contact HP worldwi
• Optional—Parts for which customer self repair is optional. These parts are also designed for customer self repair. If, however, you require that HP replace them for you, there may or may not be additional charges, depending on the type of warranty service designated for your product. NOTE: Some HP parts are not designed for customer self repair. In order to satisfy the customer warranty, HP requires that an authorized service provider replace the part.
Pour plus d'informations sur le programme CSR de HP, contactez votre Mainteneur Agrée local. Pour plus d'informations sur ce programme en Amérique du Nord, consultez le site Web HP (http://www.hp.com/go/selfrepair). Riparazione da parte del cliente Per abbreviare i tempi di riparazione e garantire una maggiore flessibilità nella sostituzione di parti difettose, i prodotti HP sono realizzati con numerosi componenti che possono essere riparati direttamente dal cliente (CSR, Customer Self Repair).
HINWEIS: Einige Teile sind nicht für Customer Self Repair ausgelegt. Um den Garantieanspruch des Kunden zu erfüllen, muss das Teil von einem HP Servicepartner ersetzt werden. Im illustrierten Teilekatalog sind diese Teile mit „No“ bzw. „Nein“ gekennzeichnet. CSR-Teile werden abhängig von der Verfügbarkeit und vom Lieferziel am folgenden Geschäftstag geliefert. Für bestimmte Standorte ist eine Lieferung am selben Tag oder innerhalb von vier Stunden gegen einen Aufpreis verfügbar.
el caso de todas sustituciones que lleve a cabo el cliente, HP se hará cargo de todos los gastos de envío y devolución de componentes y escogerá la empresa de transporte que se utilice para dicho servicio. Para obtener más información acerca del programa de Reparaciones del propio cliente de HP, póngase en contacto con su proveedor de servicios local. Si está interesado en el programa para Norteamérica, visite la página web de HP siguiente (http://www.hp.com/go/selfrepair).
• Obrigatória – Peças cujo reparo feito pelo cliente é obrigatório. Se desejar que a HP substitua essas peças, serão cobradas as despesas de transporte e mão-de-obra do serviço. • Opcional – Peças cujo reparo feito pelo cliente é opcional. Essas peças também são projetadas para o reparo feito pelo cliente. No entanto, se desejar que a HP as substitua, pode haver ou não a cobrança de taxa adicional, dependendo do tipo de serviço de garantia destinado ao produto.
Technical support 71
Technical support 72
Regulatory compliance notices Regulatory compliance identification numbers For the purpose of regulatory compliance certifications and identification, this product has been assigned a unique regulatory model number. The regulatory model number can be found on the product nameplate label, along with all required approval markings and information. When requesting compliance information for this product, always refer to this regulatory model number.
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
Canadian notice (Avis Canadien) Class A equipment This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. Class B equipment This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment.
Class B equipment Chinese notice Class A equipment Laser compliance This product may be provided with an optical storage device (that is, CD or DVD drive) and/or fiber optic transceiver. Each of these devices contains a laser that is classified as a Class 1 Laser Product in accordance with US FDA regulations and the IEC 60825-1. The product does not emit hazardous laser radiation. Each laser product complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No.
Batteries, battery packs, and accumulators should not be disposed of together with the general household waste. To forward them to recycling or proper disposal, use the public collection system or return them to HP, an authorized HP Partner, or their agents. For more information about battery replacement or proper disposal, contact an authorized reseller or an authorized service provider.
Electrostatic discharge Preventing electrostatic discharge To prevent damaging the system, be aware of the precautions you need to follow when setting up the system or handling parts. A discharge of static electricity from a finger or other conductor may damage system boards or other static-sensitive devices. This type of damage may reduce the life expectancy of the device. To prevent electrostatic damage: • Avoid hand contact by transporting and storing products in static-safe containers.
Acronyms and abbreviations CSA Canadian Standards Association CSR Customer Self Repair ESD electrostatic discharge I/O input/output IEC International Electrotechnical Commission iLO 2 Integrated Lights-Out 2 IP Internet Protocol KVM keyboard, video, and mouse LCD liquid crystal display LED light-emitting diode NEMA National Electrical Manufacturers Association NFPA National Fire Protection Association Acronyms and abbreviations 80
NIC network interface controller PDU power distribution unit TMRA recommended ambient operating temperature UID unit identification UPS uninterruptible power system USB universal serial bus Acronyms and abbreviations 81
Index A accessing a server blade with local KVM 42 accessing HP BladeSystem Insight Display 52 accessing local media devices 42 additional information 60 airflow requirements 7, 8 alerts 47, 54, 62, 63 authorized reseller 65 B batteries, replacing 77 battery replacement notice 77 bay numbering, fan 14, 15 bay numbering, full-height device 12 bay numbering, half-height device 12 bay numbering, interconnect 14, 17 bay numbering, power supply 16 bay to bay crosslinks 39 BL2x220c blades, mapping 38 Blade and P
European Union notice 75 F fan bay numbering 14, 15 fan errors 63 fan LED 15 fans 15 fans, installing 29 FCC rating label 73 Federal Communications Commission (FCC) notice 73, 74 front components 11 full-height device bay blank, creating 24 full-height device bay numbering 12 full-height server blade, installing 20 full-height server blades, mapping 36 G grounding methods 79 grounding requirements 9 H half-height device bay numbering 12 half-height server blade shelf, removing 22 half-height server blade
M management module 17 mapping BL2x220c blades 38 mapping full-height server blades 36 mapping half-height server blades 35 mapping to interconnect ports 34 mezzanine card 34 minimum requirements 9 modifications, FCC notice 74 regulatory compliance notices 73, 75, 78 removing a KVM module 32 removing interconnect bay dividers 40 required information 65 requirements, airflow 7, 8 requirements, electrical grounding 9 requirements, minimum 9 requirements, power 9 requirements, space 7, 8 requirements, tempera
W warnings 7 website, HP 44 Index 85
