Maintenance and Service Guide HP Compaq nc4400 Notebook PC Document Part Number: 383207-002 May 2006 This guide is a troubleshooting reference used for maintaining and servicing the computer. It provides comprehensive information on identifying computer features, components, and spare parts; troubleshooting computer problems; and performing computer disassembly procedures.
© Copyright 2006 Hewlett-Packard Development Company, L.P. Microsoft and Windows are U.S. registered trademarks of Microsoft Corporation. Intel, Celeron, and Core are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries. Bluetooth is a trademark owned by its proprietor and used by Hewlett-Packard Company under license. SD Logo is a trademark of its proprietor. The information contained herein is subject to change without notice.
Contents 1 Product Description 1.1 1.2 1.3 1.4 1.5 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–2 Resetting the Computer. . . . . . . . . . . . . . . . . . . . . . . 1–4 Power Management. . . . . . . . . . . . . . . . . . . . . . . . . . 1–5 External Components . . . . . . . . . . . . . . . . . . . . . . . . 1–6 Design Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . 1–20 2 Troubleshooting 2.1 Computer Setup. . . . . . . . . . . . . . . . . . . . . . . . .
Contents 3 Illustrated Parts Catalog 3.1 3.2 3.3 3.4 3.5 3.6 3.7 Serial Number Location . . . . . . . . . . . . . . . . . . . . . . 3–1 Computer Major Components. . . . . . . . . . . . . . . . . . 3–2 Display Assembly Components . . . . . . . . . . . . . . . 3–11 Plastics Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–13 Cable Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–14 Miscellaneous (Not Illustrated). . . . . . . . . . . . . . . .
Contents 5 Removal and Replacement Procedures 5.1 Serial Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–2 5.2 Disassembly Sequence Chart . . . . . . . . . . . . . . . . . . 5–3 5.3 Preparing the Computer for Disassembly . . . . . . . . . 5–5 5.4 Hard Drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–7 5.5 Computer Feet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–11 5.6 Bluetooth Module . . . . . . . . . . . . . . . . . . . . . . . . . . 5–12 5.
Contents 6 Specifications A Screw Listing B Software Backup and Recovery C Display Component Recycling D Connector Pin Assignments E Power Cord Set Requirements Index vi Maintenance and Service Guide
1 Product Description The HP Compaq nc4400 Notebook PC offers advanced modularity, Intel® Core™ Duo and Celeron® M processors, and extensive multimedia support.
Product Description 1.1 Features ■ Intel Core Duo T2600 (2.17-GHz), T2500 (2.00-GHz), T2400 (1.83-GHz), and T2300 (1.67-GHz) or Intel Celeron M 1.60-GHz processors, varying by computer model ■ 12.1-inch, XGA, TFT (1024 × 768) display with over 16.8 million colors ■ 100-, 80-, or 60-GB high-capacity hard drive, varying by computer model ■ 256-MB DDR2 synchronous DRAM (SDRAM) at 633 MHz and 533 MHz, expandable to 4.
Product Description ■ External 65-watt AC adapter with 3-wire power cord ■ 6-cell Li-Ion battery pack ■ Audio speaker ■ Volume up, volume mute, and volume down buttons ■ Connectors: ❏ Infrared ❏ Audio-out (headphone) ❏ Audio-in (microphone) ❏ Universal Serial Bus (USB) v. 2.
Product Description 1.2 Resetting the Computer If the computer you are servicing has an unknown password, follow the steps below to reset the password. These steps also clear CMOS. following steps will not clear an unknown password if the ✎ The stringent security option has been enabled in the BIOS. If stringent security is enabled, the system board must be replaced to reset an unknown password. Refer to Section 5.21, “System Board,” for more information on replacing the system board.
Product Description 1.3 Power Management The computer comes with power management features that extend battery pack operating time and conserve power.
Product Description 1.4 External Components The external components on the front of the computer are shown below and described in Table 1-1. Front Components Table 1-1 Front Components Item Component Function 1 Wireless light On: An integrated wireless device, such as a wireless local area network (WLAN) device and/or Bluetooth® device, is turned on. 2 Power light ■ On: The computer is on. ■ Blinking green: The computer is in standby. ■ Blinking rapidly: Wrong AC adapter is connected.
Product Description Table 1-1 Front Components (Continued) Item Component Function 3 Battery light ■ Amber: A battery pack is charging. ■ Green: A battery pack is close to full charge capacity. ■ Blinking amber: A battery pack that is the only available power source has reached a low-battery condition. When the battery pack reaches a critical low-battery condition, the battery light begins blinking more quickly.
Product Description The external components on the right side of the computer are shown below and described in Table 1-2.
Product Description Table 1-2 Right-Side Components Item Component Function 1 Audio-out (headphone) jack Connects an optional headphone or powered stereo speakers. Also connects the audio function of an audio/video device, such as a television or VCR. 2 Audio-in (microphone) jack Connects an optional monaural (single sound channel) or stereo (dual sound channel) microphone. 3 Powered USB port Connects USB 1.1- or 2.
Product Description The external components on the left side of the computer are shown below and described in Table 1-3. Left-Side Components Table 1-3 Left-Side Components Item Component Function 1 Security cable slot Attaches an optional security cable to the computer. purpose of security solutions is ✎ The to act as deterrents. These deterrents may not prevent a product from being mishandled or stolen. 2 Vent Provides airflow to cool internal components.
Product Description Table 1-3 Left-Side Components (Continued) Item Component Function 3 Wireless button Turns the wireless functionality of the WLAN or Bluetooth device on or off, but does not establish a connection. establish a wireless connection, ✎ To a wireless network must already be set up. 4 USB port Connects a USB 1.1- and 2.0-compliant device to the computer using a standard USB cable. 5 Info Center button Launches Info Center, which enables you to open various software solutions.
Product Description The external components on the rear panel of the computer are shown below and described in Table 1-4.
Product Description Table 1-4 Rear Panel Components Item Component Function 1 USB port Connects USB 1.1- and 2.0-compliant devices to the computer using a standard USB cable. 2 RJ-11 (modem) jack Connects a modem cable. Enabled with 56-K connectivity. 3 RJ-45 (network) jack Connects a network cable. Enabled with 10BASE-T/100BASE-TX/1000BASE-T connectivity. 4 Smart adapter power connector Connects an AC adapter, an optional AC adapter, or an optional power cable.
Product Description The standard keyboard components of the computer are shown below and described in Table 1-5.
Product Description Table 1-5 Standard Keyboard Components Item Component Function 1 Function keys (6) Perform system and application tasks. When combined with the fn key, the function keys f3, f4, and f8 through f11 perform additional tasks as hotkeys. 2 caps lock key Enables caps lock and turns on the caps lock light. 3 fn key Executes frequently used system functions when pressed in combination with a function key or the esc key.
Product Description The computer top components are shown below and described in Table 1-6.
Product Description Table 1-6 Top Components Item Component Function 1 Left and right TouchPad buttons (2) Function like the left and right buttons on an external mouse. 2 TouchPad Moves the pointer. Can be set to perform other mouse functions, such as scrolling, selecting, and double-clicking. 3 Left and right pointing stick buttons (2) Function like the left and right buttons on an external mouse. 4 Pointing stick Moves the pointer. 5 Vent Provides airflow to cool internal components.
Product Description The external components on the bottom of the computer are shown below and described in Table 1-7.
Product Description Table 1-7 Bottom Components Item Component Function 1 Base enclosure cover Covers the display cable and connector. 2 Docking connector Connects the computer to an optional docking device. 3 Accessory battery connector Connects an optional HP Ultra-Capacity Battery or HP Extended Life Battery. 4 Vents (3) Provides airflow to cool internal components. prevent overheating, do not ✎ To obstruct vents. Use the computer only a hard, flat surface.
Product Description 1.5 Design Overview This section presents a design overview of key parts and features of the computer. Refer to Chapter 3, “Illustrated Parts Catalog,” to identify replacement parts, and Chapter 5, “Removal and Replacement Procedures,” for disassembly steps.
2 Troubleshooting Å WARNING: Only authorized technicians trained by HP should repair this equipment. All troubleshooting and repair procedures are detailed to allow only subassembly-/module-level repair. Because of the complexity of the individual boards and subassemblies, do not attempt to make repairs at the component level or modifications to any printed wiring board. Improper repairs can create a safety hazard.
Troubleshooting 2. Select the File, Security, Diagnostics, or System Configuration menu. 3. To close Computer Setup and restart the computer: ❏ Select File > Save changes and exit, and then press enter. – or – ❏ Select File > Ignore changes and exit, and then press enter. – or – ❏ Select File > Restore defaults, and then press enter. 4. When you are prompted to confirm your action, press f10.
Troubleshooting Selecting from the Security Menu Table 2-2 Security Menu Select To Do This Setup Password Enter, change, or delete an Setup password. Power-On Password Enter, change, or delete a power-on password. Password Options (Password options can be selected only when a power-on password has been set.) Enable/disable: ■ Stringent security. ■ Requirement of password on restart. DriveLock Passwords Enable/disable DriveLock; change a DriveLock user or master password.
Troubleshooting Selecting from the Diagnostics Menu Table 2-3 Diagnostics Menu Select To Do This HDD Self-Test Options Run a quick comprehensive self test on hard drives in the system that support the test features.
Troubleshooting Selecting from the System Configuration Menu Table 2-4 System Configuration Menu Select To Do This Language Change the Computer Setup language. Boot Options Enable/disable MultiBoot, which sets a startup sequence that can include most bootable devices and media in the system. Device Configurations Enable/disable: ■ Swap Fn/Ctrl keys. ■ USB legacy support. ■ BIOS DMA data transfers. ■ Fan Always on while on AC Power. ■ Data Execution Prevention. ■ LAN Power save.
Troubleshooting 2.2 Troubleshooting Flowcharts Table 2-5 Troubleshooting Flowcharts Overview Flowchart Description 2.1 “Flowchart 2.1—Initial Troubleshooting” 2.2 “Flowchart 2.2—No Power, Part 1” 2.3 “Flowchart 2.3—No Power, Part 2” 2.4 “Flowchart 2.4—No Power, Part 3” 2.5 “Flowchart 2.5—No Power, Part 4” 2.6 “Flowchart 2.6—No Video, Part 1” 2.7 “Flowchart 2.7—No Video, Part 2” 2.8 “Flowchart 2.8—Nonfunctioning Docking Device (if applicable)” 2.9 “Flowchart 2.
Troubleshooting Flowchart 2.1—Initial Troubleshooting Begin troubleshooting. N Go to Is there power? “Flowchart 2.2—No Power, Part 1.” Y N Check LED board, speaker connections. Beeps, LEDs, or error messages? N Y Go to All drives working? N Go to Is there video? (no boot) Y “Flowchart 2.6—No Video, Part 1.” N Keyboard/ pointing device working? Y N Go to Is the OS loading? N Go to Is there sound? Y “Flowchart 2.9—No Operating System (OS) Loading.” Y “Flowchart 2.15—No Audio, Part 1.
Troubleshooting Flowchart 2.2—No Power, Part 1 No power (power LED is off). Remove from docking device (if applicable). N N Power up on battery power? Go to Power up on battery power? Reset power.* “Flowchart 2.3—No Power, Part 2.” Y Y N N Power up on AC power? Power up on AC power? Reset power.* Y Go to “Flowchart 2.4—No Power, Part 3.” Y Y Power up in docking device? Done *NOTES N 1. Reset the power cables in the docking device and at the AC outlet. 2.
Troubleshooting Flowchart 2.3—No Power, Part 2 Continued from “Flowchart 2.2—No Power, Part 1.” Visually check for debris in battery socket and clean if necessary. Y Power on? Done N Check battery pack by recharging it, moving it to another computer, N Replace power supply (if applicable). Power on? Y N Go to Done Power on? “Flowchart 2.4—No Power, Part 3.
Troubleshooting Flowchart 2.4—No Power, Part 3 Continued from “Flowchart 2.3—No Power, Part 2.” Plug directly into AC outlet. Y Power LED on? Done N Reseat AC adapter in computer and at power source. Y Done Power on? N External N Try different outlet. Power outlet active? Y Internal or external AC adapter? Replace external AC adapter. N Internal Go to “Flowchart 2.5—No Power, Part 4.” Replace power cord.
Troubleshooting Flowchart 2.5—No Power, Part 4 Continued from “Flowchart 2.4—No Power, Part 3.” Open computer. Y Loose or damaged parts? N Reseat loose components and boards and replace damaged items. Close computer and retest. N Power on? Replace the following items (if applicable). Check computer operation after each replacement: 1. Internal DC-DC converter* 2. Internal AC adapter 3. Processor board* 4. System board* *NOTE: Replace these items as a set to prevent shorting out among components.
Troubleshooting Flowchart 2.6—No Video, Part 1 No video. Docking Device Go to Stand-alone or docking device? *NOTE: To change from internal to external display, use the hotkey combination. “Flowchart 2.7—No Video, Part 2.” Stand-alone Internal or external display*? Y Adjust brightness. A Adjust brightness. Press lid switch to ensure operation. Y Video OK? Done N Internal External Video OK? Y Done N Video OK? Done N Replace the following one at a time. Test after each replacement. 1.
Troubleshooting Flowchart 2.7—No Video, Part 2 Continued from “Flowchart 2.6—No Video, Part 1.” Remove computer from docking device, if connected. Adjust display brightness. Check brightness of external monitor. N Y Go to “A” in “Flowchart 2.6—No Video, Part 1.” Video OK? Y Video OK? Done N Check that computer is properly seated in docking device, for bent pins on cable, and for monitor connection. Try another external monitor.
Troubleshooting Flowchart 2.8—Nonfunctioning Docking Device (if applicable) Nonfunctioning docking device. Reset power cord in docking device and power outlet. Check voltage setting on docking device. Reset monitor cable connector at docking device. Reinstall computer into docking device. Y Docking device operating? N Y Docking device operating? Done Done N Replace docking device. 2–14 Test replacement docking device with new computer.
Troubleshooting Flowchart 2.9—No Operating System (OS) Loading No OS loading.* Reset power cord in docking device and power outlet. No OS loading from hard drive, go to “Flowchart 2.10—No OS Loading, Hard Drive, Part 1.” No OS loading from diskette drive, go to “Flowchart 2.13—No OS Loading, Diskette Drive.” No OS loading from CD-ROM or DVD-ROM drive, go to “Flowchart 2.14—No OS Loading, Optical Drive.” No OS loading from network, go to “Flowchart 2.20—No Network/Modem Connection.
Troubleshooting Flowchart 2.10—No OS Loading, Hard Drive, Part 1 OS not loading from hard drive. Y Nonsystem disk message? N Go to “Flowchart 2.11—No OS Loading, Hard Drive, Part 2.” Reseat external hard drive. Y OS loading? Done N N Boot from CD? N Y Boot from diskette? Check the Setup utility for correct booting order. Y Change boot priority through the Setup Utility and reboot. N Boot from hard drive? N Y Boot from hard drive? Done Y 2–16 Go to “Flowchart 2.
Troubleshooting Flowchart 2.11—No OS Loading, Hard Drive, Part 2 Continued from “Flowchart 2.10—No OS Loading, Hard Drive, Part 1.” Reseat hard drive. N 1. Replace hard drive. 2. Replace system board. CD or diskette in drive? Y Hard drive accessible? Y Done N Remove diskette and reboot. Run FDISK. Y Boot from hard drive? N Done N Hard drive partitioned? Y N Y N Go to “Flowchart 2.13—No OS Loading, Diskette Drive.
Troubleshooting Flowchart 2.12—No OS Loading, Hard Drive, Part 3 Continued from “Flowchart 2.11—No OS Loading, Hard Drive, Part 2.” N System files on hard drive? Install OS and reboot. Y Y Y Virus on hard drive? OS loading from hard drive? Clean virus. N Done N Y Run SCANDISK and check for bad sectors. Diagnostics on diskette? Replace hard drive. N N Can bad sectors be fixed? Run diagnostics and follow recommendations. Replace hard drive. Y N Boot from hard drive? Fix bad sectors.
Troubleshooting Flowchart 2.13—No OS Loading, Diskette Drive Y OS not loading from diskette drive. Reseat diskette drive. OS loading? Done N Y N Bootable diskette in drive? Nonsystem disk message? N Y N Check diskette for system files. Try different diskette. Go to Boot from another device? “Flowchart 2.17—Nonfunctioning Device.” Y Y N Diskette drive enabled in the Setup Utility? 1. Replace diskette drive. 2. Replace system board. Nonsystem disk error? Enable drive and cold boot computer.
Troubleshooting Flowchart 2.14—No OS Loading, Optical Drive Y No OS loading from CD-ROM or DVD-ROM drive. N Install bootable disc and reboot computer. Bootable disc in drive? Disc in drive? Y N Install bootable disc. Try another bootable disc. Y Boots from CD or DVD? Done N Y Boots from CD or DVD? Reseat drive. Done N N Booting from another device? Y Y Booting order correct? N Go to “Flowchart 2.17—Nonfunctioning Device.” Reset the computer. Refer to Go to Section 1.
Troubleshooting Flowchart 2.15—No Audio, Part 1 Y Turn up audio internally or externally. No audio. Audio? Done N Y Computer in docking device (if applicable)? N Go to Internal audio? Undock N “Flowchart 2.16—No Audio, Part 2.” Y Go to Replace the docking device. “Flowchart 2.16—No Audio, Part 2.” Y Go to “Flowchart 2.17—Nonfunctioning Device.
Troubleshooting Flowchart 2.16—No Audio, Part 2 Continued from “Flowchart 2.15—No Audio, Part 1.” N Audio driver in OS configured? Reload audio drivers. Y N Correct drivers for application? Load drivers and set configuration in OS. Y Connect to external speaker. N Audio? Y Replace audio board and speaker connections in computer (if applicable). Y Audio? Done N 1. Replace internal speakers. 2. Replace audio board (if applicable). 3. Replace system board.
Troubleshooting Flowchart 2.17—Nonfunctioning Device Nonfunctioning device. Reseat device. Unplug the nonfunctioning device from the computer and inspect cables and plugs for bent or broken pins or other damage. Y Clear CMOS. Fix or replace broken item. Any physical device detected? N Reattach device. Close computer, plug in power, and reboot. Go to “Flowchart 2.9—No Operating System (OS) Loading.” Replace hard drive. N Device boots properly? N Replace NIC.
Troubleshooting Flowchart 2.18—Nonfunctioning Keyboard Keyboard not operating properly. Connect computer to good external keyboard. N External device works? Replace system board. Y Reseat internal keyboard connector (if applicable). N Replace internal keyboard or cable. OK? Y Y Done OK? Done N Replace system board.
Troubleshooting Flowchart 2.19—Nonfunctioning Pointing Device Pointing device not operating properly. Connect computer to good external pointing device. N Replace system board. External device works? Y Reseat internal pointing device connector (if applicable). N Replace internal pointing device or cable. OK? Y Y Done OK? Done N Replace system board.
Troubleshooting Flowchart 2.20—No Network/Modem Connection No network or modem connection. N Network or modem jack active? Replace jack or have jack activated. Y Y Connect to nondigital line. Digital line? N Y N NIC/modem configured in OS? Reload drivers and reconfigure. Done OK? N Y Disconnect all power from the computer and open. Replace the NIC/modem (if applicable). Y Reseat NIC/modem (if applicable). OK? Done N Replace system board.
3 Illustrated Parts Catalog This chapter provides an illustrated parts breakdown and a reference for spare part numbers. 3.1 Serial Number Location When ordering parts or requesting information, provide the computer serial number and computer model number located on the bottom of the computer.
Illustrated Parts Catalog 3.
Illustrated Parts Catalog Table 3-1 Spare Parts: Computer Major Components Spare Part Number Item Description 1 12.
Illustrated Parts Catalog Computer Major Components 3–4 Maintenance and Service Guide
Illustrated Parts Catalog Table 3-1 Spare Parts: Computer Major Components (Continued) Item Description 9 Memory modules 10 Spare Part Number PC2, 5300 2048-MB 1024-MB 512-MB 256-MB 419149-001 419145-001 419151-001 419147-001 PC2, 4200 2048-MB 1024-MB 512-MB 256-MB 419148-001 419144-001 419150-001 419146-001 Mini Card WLAN module 802.11b/g Silverton WLAN module for use in most of the world (MOW) 802.11b/g Silverton WLAN module for use in the rest of the world (ROW) 359106-001 802.
Illustrated Parts Catalog Computer Major Components 3–6 Maintenance and Service Guide
Illustrated Parts Catalog Table 3-1 Spare Parts: Computer Major Components (Continued) Item Description Spare Part Number 11 Heat sink (includes thermal paste) 419161-001 12 Thermal shield 419162-001 13 Hinge saddle 419129-001 Plastics Kit, includes: 419157-001 14a 14b 14c 14d PC Card slot spacer Bluetooth board cover Hard drive cover Memory module compartment cover Not illustrated: Computer feet (5) 15 Processors (include thermal paste) Intel Core Duo T2600 (2.
Illustrated Parts Catalog Computer Major Components 3–8 Maintenance and Service Guide
Illustrated Parts Catalog Table 3-1 Spare Parts: Computer Major Components (Continued) Item Description Spare Part Number 22 Base enclosure 419110-001 23 6-cell battery pack 419111-001 24 Hard drives (all 5400 rpm; include cover and frame) 25 26 100-GB 80-GB 60-GB 419124-001 419126-001 419125-001 Bluetooth module (includes Bluetooth module cable) 419117-001 Hard drive cover Maintenance and Service Guide 419128-001 3–9
Illustrated Parts Catalog 3.
Illustrated Parts Catalog Table 3-2 Display Assembly Components Spare Parts Number Information Item Description Spare Part Number 1 Display bezel (includes fingerprint reader board) 419133-001 2 Display inverter 419130-001 3 Microphone 419152-001 4 12.
Illustrated Parts Catalog 3.
Illustrated Parts Catalog 3.
Illustrated Parts Catalog 3.
Illustrated Parts Catalog Table 3-5 Miscellaneous Spare Part Information (Continued) Description Spare Part Number Power supply, 65 watt 419107-001 Power cords For use in: Australia and New Zealand 350188-011 Belgium, Europe, Greece, Norway, and Portugal 350188-021 Canada, French Canada, Latin America, Taiwan, Thailand, and the United States 350188-001 Denmark 350188-081 France 350188-041 Germany 350188-051 Hong Kong and the United Kingdom 350188-031 Israel 350188-BB1 Italy 350188-061
Illustrated Parts Catalog 3.7 Sequential Part Number Listing Table 3-6 Sequential Part Number Listing Spare Part Number Description 337407-001 802.11a/b/g DynaStar WLAN Mini Card WLAN module for use in most of the world 337407-002 802.11a/b/g DynaStar WLAN Mini Card WLAN module for use in the rest of the world 337407-291 802.
Illustrated Parts Catalog Table 3-6 Sequential Part Number Listing (Continued) Spare Part Number Description 350188-331 Power cord for use in the Netherlands 350188-AA1 Power cord for use in the People’s Republic of China 350188-B71 Power cord for use in Sweden/Finland 350188-BB1 Power cord for use in Israel 359106-001 802.11b/g Silverton WLAN Mini Card WLAN module for use in most of the world 359107-001 802.
Illustrated Parts Catalog Table 3-6 Sequential Part Number Listing (Continued) Spare Part Number 375557-001 Description DVD±RW and CD-RW Double-Layer Combo Drive (for use in External MultiBay II and HP Docking Station) 377408-001 802.11a/b/g ATMC WLAN Mini Card WLAN module for use in most of the world 377408-002 802.11a/b/g ATMC WLAN Mini Card WLAN module for use in the rest of the world 377408-291 802.11a/b/g ATMC WLAN Mini Card WLAN module for use in Japan 377792-001 802.
Illustrated Parts Catalog Table 3-6 Sequential Part Number Listing (Continued) Spare Part Number Description 413267-001 HP Docking Station 419107-001 65-watt power supply 419108-001 Wireless Antenna Kit (includes wireless antenna transceivers and cables) 419110-001 Base enclosure 419111-001 6-cell, 5.
Illustrated Parts Catalog Table 3-6 Sequential Part Number Listing (Continued) Spare Part Number Description 419132-001 Logo Kit 419133-001 Display bezel (includes fingerprint reader board) 419134-001 Display Cable Kit 419135-001 Display enclosure 419141-001 12.
Illustrated Parts Catalog Table 3-6 Sequential Part Number Listing (Continued) Spare Part Number Description 419157-001 Plastics Kit 419159-001 Intel Celeron M 1.
Illustrated Parts Catalog Table 3-6 Sequential Part Number Listing (Continued) Spare Part Number Description 419171-141 Keyboard with pointing stick for use in Turkey 419171-151 Keyboard with pointing stick for use in Greece 419171-161 Keyboard with pointing stick for use in Latin America 419171-171 Keyboard with pointing stick for use in Saudi Arabia 419171-201 Keyboard with pointing stick for use in Brazil 419171-211 Keyboard with pointing stick for use in Hungary 419171-221 Keyboard with
4 Removal and Replacement Preliminaries This chapter provides essential information for proper and safe removal and replacement service. 4.
Removal and Replacement Preliminaries 4.2 Service Considerations The following sections include some of the considerations that you should keep in mind during disassembly and assembly procedures. you remove each subassembly from the computer, place ✎ As the subassembly (and all accompanying screws) away from the work area to prevent damage. Plastic Parts Using excessive force during disassembly and reassembly can damage plastic parts. Use care when handling the plastic parts.
Removal and Replacement Preliminaries 4.3 Preventing Damage to Removable Drives Removable drives are fragile components that must be handled with care. To prevent damage to the computer, damage to a removable drive, or loss of information, observe the following precautions: ■ Before removing or inserting a hard drive, shut down the computer. If you are unsure whether the computer is off or in hibernation, turn the computer on, and then shut it down through the operating system.
Removal and Replacement Preliminaries 4.4 Preventing Electrostatic Damage Many electronic components are sensitive to electrostatic discharge (ESD). Circuitry design and structure determine the degree of sensitivity. Networks built into many integrated circuits provide some protection, but in many cases, the discharge contains enough power to alter device parameters or melt silicon junctions.
Removal and Replacement Preliminaries 4.5 Packaging and Transporting Precautions Use the following grounding precautions when packaging and transporting equipment: ■ To avoid hand contact, transport products in static-safe containers, such as tubes, bags, or boxes. ■ Protect all electrostatic-sensitive parts and assemblies with conductive or approved containers or packaging. ■ Keep electrostatic-sensitive parts in their containers until the parts arrive at static-free workstations.
Removal and Replacement Preliminaries 4.6 Workstation Precautions Use the following grounding precautions at workstations: ■ Cover the workstation with approved static-shielding material (refer to Table 4-2, “Static-Shielding Materials”). ■ Use a wrist strap connected to a properly grounded work surface and use properly grounded tools and equipment. ■ Use conductive field service tools, such as cutters, screwdrivers, and vacuums.
Removal and Replacement Preliminaries 4.7 Grounding Equipment and Methods Grounding equipment must include either a wrist strap or a foot strap at a grounded workstation. ■ When seated, wear a wrist strap connected to a grounded system. Wrist straps are flexible straps with a minimum of one megohm ±10% resistance in the ground cords. To provide proper ground, wear a strap snugly against the skin at all times. On grounded mats with banana-plug connectors, use alligator clips to connect a wrist strap.
Removal and Replacement Preliminaries Table 4-1 shows how humidity affects the electrostatic voltage levels generated by different activities.
5 Removal and Replacement Procedures This chapter provides removal and replacement procedures. There are as many as 70 screws, in 10 different sizes, that may have to be removed, replaced, or loosened when servicing the computer. Make special note of each screw and screw lock size and location during removal and replacement. Refer to Appendix A, “Screw Listing,” for detailed information on screw and screw lock sizes, locations, and usage.
Removal and Replacement Procedures 5.1 Serial Number Report the computer serial number to HP when requesting information or ordering spare parts. The serial number is located on the bottom of the computer.
Removal and Replacement Procedures 5.2 Disassembly Sequence Chart Use the chart below to determine the section number to be referenced when removing computer components. Disassembly Sequence Chart Section Description # of Screws Removed 5.3 Preparing the Computer for Disassembly battery pack 0 5.4 Hard Drive 2 loosened to remove the hard drive cover 1 loosened to remove the hard drive 4 removed to disassemble the hard drive 5.5 Computer Feet 0 5.
Removal and Replacement Procedures Disassembly Sequence Chart (Continued) Section Description # of Screws Removed 5.14 Mini Card WLAN Module 2 Å To prevent an unresponsive system and the display of a warning message, install only a Mini Card WLAN device authorized for use in your computer by the governmental agency that regulates wireless devices in your country. If you install a device and then receive a warning message, remove the device to restore computer functionality.
Removal and Replacement Procedures 5.3 Preparing the Computer for Disassembly Before you begin any removal or installation procedures: 1. Shut down the computer. If you are unsure whether the computer is off or in hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3. Disconnect the power cord.
Removal and Replacement Procedures Battery Pack Spare Part Number Information 6-cell battery pack 419111-001 4. Remove the battery pack by following these steps: a. Turn the computer upside down with the front toward you. b. Slide the battery release latch 1 toward the back of the computer. (The right side of the battery pack disengages from the computer.) c. Lift the right side of the battery pack and swing it to the left 2 and remove it.
Removal and Replacement Procedures 5.4 Hard Drive Hard Drive Spare Part Number Information Hard drives (all 5400 rpm; include cover and frame) 100-GB 80-GB 60-GB 419124-001 419126-001 419125-001 1. Prepare the computer for disassembly (Section 5.3).
Removal and Replacement Procedures 2. Loosen the two Phillips PM2.0×5.0 screws 1 that secure the hard drive cover to the computer. 3. Lift the left side of the hard drive cover and swing it to the right 2 and remove it. hard drive cover is available using spare part 419128-001 ✎ The and is also included in the Plastics Kit, spare part number 419157-001.
Removal and Replacement Procedures 4. Loosen the Phillips PM2.5×13.0 hard drive retention screw 1. 5. Grasp the mylar tab 2 on the hard drive and slide the hard drive to the right 3 to disconnect it from the system board. 6. Remove the hard drive 4.
Removal and Replacement Procedures 7. Remove the four Phillips PM3.0×4.0 screws 1 that secure the hard drive frame to the hard drive. 8. Lift the frame straight up 2 to remove if from the hard drive. Removing the Hard Drive Frame Reverse the above procedure to reassemble and install the hard drive.
Removal and Replacement Procedures 5.5 Computer Feet The computer feet are adhesive-backed rubber pads. The feet are included in the Plastics Kit, spare part number 419157-001.
Removal and Replacement Procedures 5.6 Bluetooth Module Bluetooth Module Spare Part Number Information Bluetooth module (includes Bluetooth module cable) 419117-001 1. Prepare the computer for disassembly (Section 5.3). 2. Remove the hard drive cover (Section 5.4). 3. Position the computer with the front toward you. 4. Loosen the two Phillips PM2.0×5.0 screws 1 that secure the Bluetooth module cover to the computer. 5. Remove the Bluetooth module cover 2.
Removal and Replacement Procedures 6. Slide the Bluetooth module out of the computer 1. 7. Disconnect the Bluetooth module cable 2 from the board. Removing the Bluetooth Module Reverse the above procedure to install the Bluetooth module.
Removal and Replacement Procedures 5.7 External Memory Module Memory Module Spare Part Number Information PC2, 5300 2048-MB 1024-MB 512-MB 256-MB 419149-001 419145-001 419151-001 419147-001 PC2, 4200 2048-MB 1024-MB 512-MB 256-MB 419148-001 419144-001 419150-001 419146-001 1. Prepare the computer for disassembly (refer to Section 5.3). 2. Position the computer with the front toward you.
Removal and Replacement Procedures 3. Loosen the two Phillips PM2.0×5.0 screws 1 that secure the memory module compartment cover to the computer. 4. Lift the left side of the cover and swing it to the right 2 to remove the memory module compartment cover. memory module compartment cover is included in the ✎ The Plastics Kit, spare part number 419157-001.
Removal and Replacement Procedures 5. Spread the retaining tabs 1 on each side of the memory module socket to release the memory module. (The side of the module opposite the socket rises away from the computer.) 6. Slide the module away from the socket at an angle 2. 7. Remove the memory module. modules are designed with a notch 3 to prevent ✎ Memory incorrect installation into the memory module socket. Removing the Memory Module Reverse the above procedure to install an external memory module.
Removal and Replacement Procedures 5.8 Keyboard Cover Keyboard Cover Spare Part Number Information Keyboard cover 419119-001 1. Prepare the computer for disassembly (Section 5.3). 2. Position the computer with the front toward you. 3. Remove the two Torx8 T8M2.0×20.0 screws that secure the keyboard cover to the computer.
Removal and Replacement Procedures 4. Turn the computer right-side up with the front toward you. 5. Open the computer as far as possible. 6. Lift the front edge of the keyboard cover until it detaches from the computer.
Removal and Replacement Procedures 7. Lift the keyboard cover straight up and remove it. Removing the Keyboard Cover Reverse the above procedure to install the keyboard cover.
Removal and Replacement Procedures 5.
Removal and Replacement Procedures 4. Remove the following: 1 Three Torx8 T8M2.0×10.0 screws 2 One Torx8 T8M2.0×5.
Removal and Replacement Procedures 5. Turn the computer right-side up with the front toward you. 6. Open the computer as far as possible. 7. Slide the keyboard back 1 until the pointing stick cable is accessible. 8. Release the zero insertion force (ZIF) connector to which the pointing stick cable is connected and disconnect the pointing stick cable 2 from the system board.
Removal and Replacement Procedures 9. Lift the rear edge of the keyboard 1 until it disengages from the computer. 10. Slide the keyboard forward 2 until it rests on the palm rest. 11. Release the ZIF connector to which the keyboard cable is connected and disconnect the keyboard cable 3 from the system board. 12. Remove the keyboard. Removing the Keyboard Reverse the above procedure to install the keyboard.
Removal and Replacement Procedures 5.10 Fan Fan Spare Part Number Information Fan 419127-001 1. Prepare the computer for disassembly (Section 5.3). 2. Remove the keyboard cover (Section 5.8). 3. Release the keyboard (Section 5.9). 4. Disconnect the fan cable 1 from the system board. 5. Remove the three Torx8 T8M2.0×7.0 screws 2 that secure the fan to the computer. 6. Remove the fan 3. Removing the Fan Reverse the above procedure to install the fan.
Removal and Replacement Procedures 5.11 Heat Sink Heat Sink Spare Part Number Information Heat sink (includes thermal paste) 419161-001 1. Prepare the computer for disassembly (Section 5.3). 2. Remove the keyboard cover (Section 5.8). 3. Release the keyboard (Section 5.9). 4. Remove the fan (Section 5.10). 5. Remove the four Phillips PM2.5×7.0 screws that secure the heat sink to the computer.
Removal and Replacement Procedures 6. Lift the right side of the heat sink 1 to disengage it from the processor. 7. Slide the heat sink up and to the right 2 to remove it. to the adhesive quality of the thermal paste located ✎ Due between the heat sink and processor, it may be necessary to move the heat sink from side to side to detach the heat sink from the processor.
Removal and Replacement Procedures thermal paste should be thoroughly cleaned from the ✎ The surfaces of the heat sink 1 and processor 2 each time the heat sink is removed. Thermal paste is included with all heat sink and processor spare part kits. Thermal Paste Locations Reverse the above procedure to install the heat sink.
Removal and Replacement Procedures 5.12 Processor ✎ All processor spare part kits include thermal paste. Processor Spare Part Number Information Intel Core Duo T2600 (2.17-GHz) Intel Core Duo T2500 (2.00-GHz) Intel Core Duo T2400 (1.83-GHz) Intel Core Duo T2300 (1.67-GHz) 409972-001 409971-001 409970-001 409969-001 Intel Celeron M 1.60-GHz 419159-001 1. Prepare the computer for disassembly (Section 5.3). 2. Remove the keyboard cover (Section 5.8). 3. Release the keyboard (Section 5.9). 4.
Removal and Replacement Procedures 6. Use a flat-bladed screwdriver to turn the processor locking screw one-half turn counterclockwise 1 until you hear a click. 7. Lift the processor straight up and remove it 2. The gold triangle 3 on the processor should be aligned with ✎ the triangle icon 4 on the processor socket when you install the processor. Removing the Processor Reverse the above procedure to install the processor.
Removal and Replacement Procedures 5.13 Internal Memory Module Memory Module Spare Part Number Information PC2, 5300 2048-MB 1024-MB 512-MB 256-MB 419149-001 419145-001 419151-001 419147-001 PC2, 4200 2048-MB 1024-MB 512-MB 256-MB 419148-001 419144-001 419150-001 419146-001 1. Prepare the computer for disassembly (Section 5.3). 2. Remove the keyboard cover (Section 5.8). 3. Release the keyboard (Section 5.9).
Removal and Replacement Procedures 4. Spread the retaining tabs 1 on each side of the memory module socket to release the memory module. (The side of the memory module opposite the socket rises away from the computer.) 5. Slide the memory module away from the socket at an angle 2. 6. Remove the memory module. modules are designed with a notch 3 to prevent ✎ Memory incorrect installation into the memory module socket.
Removal and Replacement Procedures 5.14 Mini Card WLAN Module Mini Card WLAN Module Spare Part Number Information 802.11b/g Silverton WLAN module for most of the world (MOW) use 359106-001 802.11b/g Silverton WLAN module for rest of the world (ROW) use 359107-001 802.11a/b/g FRLN WLAN card for MOW use 373888-001 802.11a/b/g FRLN WLAN card for ROW use 373889-001 802.11a/b/g FRLN WLAN card for use in Japan 373888-291 802.11a/b/g FRLN WLAN card for use in Europe 377792-001 802.
Removal and Replacement Procedures 4. Make note of which antenna cable is attached to which antenna clip on the Mini Card WLAN module, then disconnect the auxiliary and main antenna cables 1 from the Mini Card WLAN module. 5. Remove the two Phillips PM2.0×4.0 screws 2 that secure the Mini Card WLAN module to the computer. (The edge of the Mini Card WLAN module opposite the socket rises away from the computer.) 6. Remove the Mini Card WLAN module by pulling the module away from the socket at an angle 3.
Removal and Replacement Procedures 5.15 Display Assembly Display Assembly Spare Part Number Information 12.1-inch, XGA, TFT display assembly (includes wireless antenna transceivers and cables, microphone, fingerprint reader board, and display cable) 419155-001 1. Prepare the computer for disassembly (Section 5.3). 2. Remove the keyboard cover (Section 5.8). 3. Remove the keyboard (Section 5.9). 4. Close the computer. 5. Turn the computer upside down with the rear panel toward you. 6.
Removal and Replacement Procedures 8. Remove the base enclosure cover. base enclosure cover is available using spare part number ✎ The 383520-001.
Removal and Replacement Procedures 9. Disconnect the display cable from the system board.
Removal and Replacement Procedures 10. Route the display cable through the opening between the base enclosure and the top cover.
Removal and Replacement Procedures 11. Turn the computer right-side up with the front toward you. 12. Open the computer as far as possible. 13. Disconnect the wireless antenna cables from the Mini Card WLAN module 1. 14. Disconnect the microphone cable 2 from the system board. 15. Remove the wireless antenna cables and the microphone cable from the routing channel 3 and clips 4 through which the cables are routed.
Removal and Replacement Procedures 16. Route the display cable through the opening in the computer 1. 17. Remove the two Phillips PM2.0×20.0 screws 2 that secure the display assembly to the computer. 18. Remove the display assembly 3.
Removal and Replacement Procedures Display Assembly Subcomponents Spare Parts Number Information Display bezel (includes fingerprint reader board) 419133-001 19. Remove the four rubber screw covers 1 and 2 and the four Phillips PM2.0×6.0 screws 3 that secure the display bezel to the display assembly. display bezel rubber screw covers 1 on the top edge of the ✎ The display bezel are thicker than the rubber screw covers 2 on the bottom edge of the display bezel.
Removal and Replacement Procedures 20. Flex the insides edges of the left 1 and top and bottom 2 edges of the display bezel until the bezel disengages from the display enclosure. 21. Swing the bezel 3 up and to the right until it rests beside the display assembly.
Removal and Replacement Procedures 22. Disconnect the fingerprint reader board cable from the fingerprint reader board. Removing the Fingerprint Reader Board 23. Remove the display bezel.
Removal and Replacement Procedures Display Assembly Subcomponents Spare Part Number Information Microphone 419152-001 24. Remove the microphone from the clip in the display enclosure.
Removal and Replacement Procedures Display Assembly Subcomponents Spare Part Number Information Display inverter 419130-001 25. Remove the Phillips PM2.0×6.0 screw 1 that secures the display inverter to the display enclosure. 26. Disconnect the display 2 and backlight cables 3 from the inverter. 27. Remove the display inverter 4.
Removal and Replacement Procedures Display Assembly Subcomponents Spare Part Number Information 12.1-inch WXGA, TFT display panel 419141-001 28. Remove the two Phillips PM2.0×6.0 screws 1 that secure the display panel to the display enclosure. 29. Remove the display panel 2 from the display enclosure.
Removal and Replacement Procedures display hinges are included in the Display Bracket Kit, ✎ The spare part number 431167-001. 30. If it is necessary to replace the display hinges, remove the Phillips PM2.0×6.0 screw 1 that secures each hinge to the display enclosure. 31. Remove the display hinges 2.
Removal and Replacement Procedures Display Assembly Subcomponents Spare Part Number Information Wireless Antenna Kit 419108-001 32. If it is necessary to replace the wireless antenna transceivers and cables, remove the Phillips PM2.0×6.0 screw 1 that secures each transceiver to the display enclosure. 33. Remove the wireless antenna transceivers 2 and cables 3 from the display enclosure.
Removal and Replacement Procedures 5.16 Button Board Button Board Spare Part Number Information Button board (includes button board cable) 419112-001 1. Prepare the computer for disassembly (Section 5.3) and remove the following components: a. Keyboard cover (Section 5.8) b. Keyboard (Section 5.9) c. Display assembly (Section 5.
Removal and Replacement Procedures 2. Disconnect the button board cable 1 from the system board. 3. Remove the Phillips PM2.0×4.0 screw 2 that secures the button board to the top cover.
Removal and Replacement Procedures 4. Lift the left side of the button board 1. 5. Slide the button board to the left 2 and remove it. Removing the Button Board Reverse the above procedure to install the button board.
Removal and Replacement Procedures 5.17 Top Cover Top Cover Spare Part Number Information Top cover 419163-001 1. Prepare the computer for disassembly (Section 5.3) and remove the following components: a. Hard drive (Section 5.4) b. Keyboard cover (Section 5.8) c. Keyboard (Section 5.9) d. Display assembly (Section 5.15) e. Button board (Section 5.16) 2. Turn the computer upside down with the front toward you.
Removal and Replacement Procedures 3. Remove the seven Torx8 T8M2.0×10.0 screws that secure the top cover to the computer.
Removal and Replacement Procedures 4. Turn the computer right-side up with the front toward you. 5. Remove the two Torx8 T8M2.0×20.0 screws 1 that secure the rear keyboard cover to the computer. 6. Remove the rear keyboard cover 2. rear keyboard cover is available using spare part number ✎ The 419120-001. 7. Remove the Phillips PM2.0×4.0 screw 3 that secures the top cover to the computer.
Removal and Replacement Procedures 8. Disconnect the TouchPad cable 1 from the system board. 9. Lift the rear edge of the top cover 2 until it disengages from the base enclosure. 10. Lift the top cover straight up 3 and remove it. Removing the Top Cover Reverse the above procedure to install the top cover.
Removal and Replacement Procedures 5.18 TouchPad TouchPad Spare Part Number Information TouchPad (includes cable and bracket) 419165-001 1. Prepare the computer for disassembly (Section 5.3) and remove the following components: a. Hard drive (Section 5.4) b. Keyboard cover (Section 5.8) c. Keyboard (Section 5.9) d. Display assembly (Section 5.15) e. Button board (Section 5.16) f. Top cover (Section 5.17) 2. Turn the top cover upside down with the front toward you.
Removal and Replacement Procedures 3. Remove the four Phillips PM2.0×4.0 screws that secure the TouchPad bracket to the top cover.
Removal and Replacement Procedures 4. Lift the right side of the TouchPad bracket 1 until it rests at an angle. 5. Slide the TouchPad bracket to the right 2 and remove it.
Removal and Replacement Procedures 6. Release the ZIF connector to which the TouchPad cable is attached and disconnect the TouchPad cable 1. 7. Slide the TouchPad 2 to the right and remove it. 8. If it is necessary to replace the TouchPad cable, disconnect the cable 3 from the TouchPad board. Removing the TouchPad Reverse the above procedure to install the TouchPad.
Removal and Replacement Procedures 5.19 Speaker Speaker Spare Part Number Information Speaker 419160-001 1. Prepare the computer for disassembly (Section 5.3) and remove the following components: a. Hard drive (Section 5.4) b. Keyboard cover (Section 5.8) c. Keyboard (Section 5.9) d. Display assembly (Section 5.15) e. Button board (Section 5.16) f. Top cover (Section 5.
Removal and Replacement Procedures 2. Disconnect the speaker cable 1 from the system board and route the cable under the infrared board cable 2. 3. Remove the two Torx8 T8M2.0×5.0 screws 3 that secure the speaker to the computer. 4. Remove the speaker 4. Removing the Speaker Reverse the above procedure to install the speaker.
Removal and Replacement Procedures 5.20 Infrared Board Infrared Board Spare Part Number Information Infrared board (includes cable) 419113-001 1. Prepare the computer for disassembly (Section 5.3) and remove the following components: a. Hard drive (Section 5.4) b. Keyboard cover (Section 5.8) c. Keyboard (Section 5.9) d. Display assembly (Section 5.15) e. Button board (Section 5.16) f. Top cover (Section 5.17) g. Speaker (Section 5.
Removal and Replacement Procedures 2. Release the ZIF connector to which the infrared board cable is connected and disconnect the cable 1 from the system board. 3. Remove the Torx8 T8M2.0×5.0 screw 2 that secures the infrared board to the system board. 4. Remove the infrared board 3. Removing the Infrared Board Reverse the above procedure to install the infrared board .
Removal and Replacement Procedures 5.21 System Board System Board Spare Part Number Information System board 419116-001 replacing the system board, be sure that the following ✎ When components are removed from the defective system board and installed on the replacement system board: ■ Memory modules (Section 5.7 and Section 5.13) ■ Processor (Section 5.12) ■ Mini Card WLAN module (Section 5.14) ■ Modem module (Section 5.22) ■ RTC battery (Section 5.23) 1. Prepare the computer for disassembly (Section 5.
Removal and Replacement Procedures 2. Disconnect the Bluetooth module cable 1 from the system board and remove the cable. 3. Remove the four Torx8 T8M2.0×5.0 screws 2 that secure the system board to the computer.
Removal and Replacement Procedures 4. Remove the Torx8 T8M2.0×8.0 screw 1 that secures the display support frame to the computer. 5. Remove the hinge saddle 2. 6. Remove the Torx8 T8M2.0×8.0 screw 3 that secures the thermal shield to the computer. 7. Remove the thermal shield 4. hinge saddle is available using spare part number ✎ The 419129-001. The thermal shield is available using spare part number 419162-001.
Removal and Replacement Procedures thermal paste should be thoroughly cleaned from the ✎ The surfaces of the video chip shield 1 and video chip 2 each time the shield is removed. Thermal paste is included with the system board spare part kit.
Removal and Replacement Procedures 8. Lift the left side of the system board 1 until the hard drive connector 2 is clear of the base enclosure. 9. Slide the system board 3 to the left at an angle and remove it. Removing the System Board Reverse the above procedure to install the system board.
Removal and Replacement Procedures 5.22 Modem Module Modem Module Spare Part Number Information Modem module (high-speed 56 K, includes modem module cable) 419143-001 1. Prepare the computer for disassembly (Section 5.3) and remove the following components: a. b. c. d. e. f. g. h. i. j. k. l. Hard drive (Section 5.4) Bluetooth module (Section 5.6) Keyboard cover (Section 5.8) Keyboard (Section 5.9) Fan (Section 5.10) Heat sink (Section 5.11) Display assembly (Section 5.15) Button board (Section 5.
Removal and Replacement Procedures 3. Disconnect the modem module cable from the two connectors 1 on the system board. 4. Remove the two Phillips PM2.0×4.0 screws 2 that secure the modem board to the system board. 5. Lift the right side of the modem board 3 to disconnect it from the system board. 6. Remove the modem board. Removing the Modem Board Reverse the above procedure to install the modem board.
Removal and Replacement Procedures 5.23 RTC Battery RTC Battery Spare Part Number Information RTC battery 383625-001 1. Prepare the computer for disassembly (Section 5.3) and remove the following components: a. b. c. d. e. f. g. h. i. j. k. l. Hard drive (Section 5.4) Bluetooth module (Section 5.6) Keyboard cover (Section 5.8) Keyboard (Section 5.9) Fan (Section 5.10) Heat sink (Section 5.11) Display assembly (Section 5.15) Button board (Section 5.16) Top cover (Section 5.17) Speaker (Section 5.
Removal and Replacement Procedures 3. Remove the RTC battery from the system board socket. Removing the RTC Battery Reverse the above procedure to install the RTC battery. Make sure the RTC battery is installed with the “+” sign facing up.
6 Specifications This chapter provides physical and performance specifications. Table 6-1 Computer Dimensions Height (front to back) Width Depth Weight Metric U.S. 30.2 to 31.5 mm 285 mm 235 mm 1.19 to 1.24 in 11.22 in 9 in 1.81 kg 3.99 lbs Input Power Operating voltage Operating current 18.5 V dc @ 3.5 A - 65 W 3.
Specifications Table 6-1 Computer (Continued) Relative humidity (noncondensing) Operating Nonoperating 10% to 90% 5% to 95% 10% to 90% 5% to 95% -15 m to 3,048 m -15 m to 12,192 m -50 ft to 10,000 ft -50 ft to 40,000 ft Maximum altitude (unpressurized) Operating (14.7 to 10.1 psia) Nonoperating (14.7 to 4.4 psia) Shock Operating Nonoperating 125 g, 2 ms, half-sine 200 g, 2 ms, half-sine Random Vibration Operating Nonoperating 0.75 g zero-to-peak, 10 Hz to 500 Hz, 0.25 oct/min sweep rate 1.
Specifications Table 6-2 12.1-inch, XGA, TFT Display Dimensions Height Width Diagonal 20.7 cm 33.1 cm 39.1 cm Number of colors Up to 16.8 million Contrast ratio 150:1 Brightness 150 nits typical 8.1 in 13.0 in 15.4 in Pixel resolution Pitch Format Configuration 0.300 × 0.300 mm 1024 × 768 RGB vertical stripe Backlight Edge lit Character display 80 × 25 Total power consumption 3.
Specifications Table 6-3 Hard Drives 100-GB* 80-GB* 60-GB* 9.5 mm 70 mm 99 g 9.5 mm 70 mm 102 g 9.
Specifications Table 6-4 Primary 6-cell, Li-Ion Battery Pack Dimensions Height Width Depth Weight 2.00 cm 9.40 cm 13.40 cm 0.34 kg 0.79 in 3.70 in 5.28 in 0.75 lb Energy Voltage Amp-hour capacity Watt-hour capacity 10.8 V 4.
Specifications Table 6-5 System DMA Hardware DMA System Function DMA0 Not applicable DMA1* Not applicable DMA2* Not applicable DMA3 Not applicable DMA4 Direct memory access controller DMA5* Available for PC Card DMA6 Not assigned DMA7 Not assigned *PC Card controller can use DMA 1, 2, or 5.
Specifications Table 6-6 System Interrupts Hardware IRQ System Function IRQ0 System timer IRQ1 Standard 101-/102-Key or Microsoft Natural Keyboard IRQ2 Cascaded IRQ3 Intel 82801DB/DBM USB2 Enhanced Host Controller—24CD IRQ4 COM1 IRQ5* Conexant AC—Link Audio Intel 82801DB/DBM SMBus Controller—24C3 Data Fax Modem with SmartCP IRQ6 Diskette drive IRQ7* Parallel port IRQ8 System CMOS/real-time clock IRQ9* Microsoft ACPI-compliant system IRQ10* Intel USB UHCI controller—24C2 Intel 82852/8
Specifications Table 6-6 System Interrupts (Continued) IRQ11 Intel USB EHCI controller—24CD Intel USB UHCI controller—24C4 Intel USB UHCI controller—24C7 Intel Pro/Wireless 2200BG TI OHCI 1394 host controller TI PCI1410 CardBus controller IRQ12 Synaptics PS/2 TouchPad IRQ13 Numeric data processor IRQ14 Primary IDE channel IRQ15 Secondary IDE channel *Default configuration; audio possible configurations are IRQ5, IRQ7, IRQ9, IRQ10, or none.
Specifications Table 6-7 System I/O Addresses I/O Address (hex) System Function (shipping configuration) 000 - 00F DMA controller no. 1 010 - 01F Unused 020 - 021 Interrupt controller no.
Specifications Table 6-7 System I/O Addresses (Continued) I/O Address (hex) System Function (shipping configuration) 0A2 - 0BF Unused 0C0 - 0DF DMA controller no.
Specifications Table 6-7 System I/O Addresses (Continued) I/O Address (hex) System Function (shipping configuration) 2F0 - 2F7 Unused 2F8 - 2FF Infrared port 300 - 31F Unused 320 - 36F Unused 370 - 377 Secondary diskette drive controller 378 - 37F Parallel port (LPT1/default) 380 - 387 Unused 388 - 38B FM synthesizer—OPL3 38C - 3AF Unused 3B0 - 3BB VGA 3BC - 3BF Reserved (parallel port/no EPP support) 3C0 - 3DF VGA 3E0 - 3E1 PC Card controller in CPU 3E2 - 3E3 Unused 3E8 - 3EF
Specifications Table 6-8 System Memory Map Size Memory Address System Function 640 KB 00000000-0009FFFF Base memory 128 KB 000A0000-000BFFFF Video memory 48 KB 000C0000-000CBFFF Video BIOS 160 KB 000C8000-000E7FFF Unused 64 KB 000E8000-000FFFFF System BIOS 15 MB 00100000-00FFFFFF Extended memory 58 MB 01000000-047FFFFF Super extended memory 58 MB 04800000-07FFFFFF Unused 2 MB 08000000-080FFFFF Video memory (direct access) 4 GB 08200000-FFFEFFFF Unused 64 KB FFFF0000-FFFFFF
A Screw Listing This appendix provides specification and reference information for the screws and screw locks used in the computer. All screws and screw locks listed in this appendix are available in the Screw Kit, spare part number 373556-001.
Screw Listing Table A-1 Phillips PM2.0×5.0 Screw mm Color Qty. Length Thread Head Width Black 6 5.0 mm 2.0 mm 4.5 mm Where used: 1 Two screws that secure the hard drive cover to the computer (screws are captured on the cover by C-clips; documented in Section 5.4) 2 Two screws that secure the memory module compartment cover to the computer (screws are captured on the cover by C-clips; documented in Section 5.7) Phillips PM2.0×5.
Screw Listing Table A-1 Phillips PM2.0×5.0 Screw (Continued) mm Color Qty. Length Thread Head Width Black 6 5.0 mm 2.0 mm 4.5 mm Where used: 2 screws that secure the Bluetooth module cover to the computer (screws are captured on the cover by C-clips; documented in Section 5.6) Phillips PM2.0×5.
Screw Listing Table A-2 Phillips PM2.5×13.0 Spring-Loaded Hard Drive Retention Screw mm Color Qty. Length Thread Head Width Black 1 13.0 mm 2.5 mm 5.5 mm Where used: 1 One screw that secures the hard drive to the computer (screw is captured on the cover by a C-clip; documented in Section 5.4) Table A-3 Phillips PM3.0×4.0 Screw mm Color Qty. Length Thread Head Width Silver 4 4.0 mm 3.0 mm 5.
Screw Listing Table A-4 Torx T8M2.0×20.0 Screw mm Color Qty. Length Thread Head Width Black 8 20.0 mm 2.0 mm 4.5 mm Where used: 2 screws that secure the keyboard cover to the computer (documented in Section 5.8) Torx T8M2.0×20.
Screw Listing Table A-4 Torx T8M2.0×20.0 Screw (Continued) mm Color Qty. Length Thread Head Width Black 8 20.0 mm 2.0 mm 4.5 mm Where used: 2 screws that secure the base enclosure cover to the computer (documented in Section 5.15) Torx T8M2.0×20.
Screw Listing Table A-4 Torx T8M2.0×20.0 Screw (Continued) mm Color Qty. Length Thread Head Width Black 8 20.0 mm 2.0 mm 4.5 mm Where used: 2 screws that secure the display assembly to the computer (documented in Section 5.15) Torx T8M2.0×20.
Screw Listing Table A-4 Torx T8M2.0×20.0 Screw (Continued) mm Color Qty. Length Thread Head Width Black 8 20.0 mm 2.0 mm 4.5 mm Where used: 2 screws that secure the rear keyboard cover to the computer (documented in Section 5.17) Torx T8M2.0×20.
Screw Listing Table A-5 Torx T8M2.0×10.0 Screw mm Color Qty. Length Thread Head Width Black 12 10.0 mm 2.0 mm 4.5 mm Where used: 1 Three screws that secure the keyboard to the computer (documented in Section 5.9) 2 Two screws that secure the display assembly to the computer (documented in Section 5.15) Torx T8M2.0×10.
Screw Listing Table A-5 Torx T8M2.0×10.0 Screw (Continued) mm Color Qty. Length Thread Head Width Black 12 10.0 mm 2.0 mm 4.5 mm Where used: 7 screws that secure the top cover to the computer (documented in Section 5.17) Torx T8M2.0×10.
Screw Listing Table A-6 Torx T8M2.0×5.0 Screw mm Color Qty. Length Thread Head Width Black 8 5.0 mm 2.0 mm 4.5 mm Where used: One screw that secures the keyboard to the computer (documented in Section 5.9) Torx T8M2.0×5.
Screw Listing Table A-6 Torx T8M2.0×5.0 Screw (Continued) mm Color Qty. Length Thread Head Width Black 8 5.0 mm 2.0 mm 4.5 mm Where used: 1 Two screws that secure the speaker to the computer (documented in Section 5.19) 2 One screw that secures the infrared board to the computer (documented in Section 5.20) Torx T8M2.0×5.
Screw Listing Table A-6 Torx T8M2.0×5.0 Screw (Continued) mm Color Qty. Length Thread Head Width Black 8 5.0 mm 2.0 mm 4.5 mm Where used: 4 screws that secure the system board to the computer (documented in Section 5.21) Torx T8M2.0×5.
Screw Listing Table A-7 Torx T8M2.0×8.0 Screw mm Color Qty. Length Thread Head Width Black 5 8.0 mm 2.0 mm 5.0 mm Where used: 3 screws that secure the fan to the computer (documented in Section 5.10) Torx T8M2.0×8.
Screw Listing Table A-7 Torx T8M2.0×8.0 Screw (Continued) mm Color Qty. Length Thread Head Width Black 5 8.0 mm 2.0 mm 5.0 mm Where used: 1 One screw that secures the system board and display support frame to the computer (documented in Section 5.21) 2 One screw that secures the system board and thermal shield to the computer (documented in Section 5.21) Torx T8M2.0×8.
Screw Listing Table A-8 Phillips PM2.5×7.0 Screw mm Color Qty. Length Thread Head Width Black 4 7.0 mm 2.5 mm 5.0 mm Where used: 4 screws that secure the heat sink to the computer (documented in Section 5.11) Phillips PM2.5×7.
Screw Listing Table A-9 Phillips PM2.0×4.0 Screw mm Color Qty. Length Thread Head Width Silver 10 4.0 mm 2.0 mm 4.0 mm Where used: 2 screws that secure the Mini Card WLAN module to the computer (documented in Section 5.14) Phillips PM2.0×4.
Screw Listing Table A-9 Phillips PM2.0×4.0 Screw (Continued) mm Color Qty. Length Thread Head Width Silver 10 4.0 mm 2.0 mm 4.0 mm Where used: 1 One screw that secures the button board to the computer (documented in Section 5.16) 2 One screw that secures the top cover to the computer (documented in Section 5.17) Phillips PM2.0×4.
Screw Listing Table A-9 Phillips PM2.0×4.0 Screw (Continued) mm Color Qty. Length Thread Head Width Silver 10 4.0 mm 2.0 mm 4.0 mm Where used: 4 screws that secure the TouchPad bracket to the top cover (documented in Section 5.18) Phillips PM2.0×4.
Screw Listing Table A-9 Phillips PM2.0×4.0 Screw (Continued) mm Color Qty. Length Thread Head Width Silver 10 4.0 mm 2.0 mm 4.0 mm Where used: 2 screws that secure the modem module to the system board (documented in Section 5.22) Phillips PM2.0×4.
Screw Listing Table A-10 Phillips PM2.0×6.0 Screw mm Color Qty. Length Thread Head Width Silver 11 6.0 mm 2.0 mm 5.0 mm Where used: 4 screws that secure the display bezel to the display assembly (documented in Section 5.15) Phillips PM2.0×6.
Screw Listing Table A-10 Phillips PM2.0×6.0 Screw (Continued) mm Color Qty. Length Thread Head Width Silver 11 6.0 mm 2.0 mm 5.0 mm Where used: One screw that secures the display inverter to the display assembly (documented in Section 5.15) Phillips PM2.0×6.
Screw Listing Table A-10 Phillips PM2.0×6.0 Screw (Continued) mm Color Qty. Length Thread Head Width Silver 11 6.0 mm 2.0 mm 5.0 mm Where used: 1 Two screws that secure the display panel to the display assembly (documented in Section 5.15) 2 Two screws that secure the display hinges to the display assembly (documented in Section 5.15) Phillips PM2.0×6.
Screw Listing Table A-10 Phillips PM2.0×6.0 Screw (Continued) mm Color Qty. Length Thread Head Width Silver 11 6.0 mm 2.0 mm 5.0 mm Where used: 2 screws that secure the wireless antenna transceivers to the display assembly (documented in Section 5.15) Phillips PM2.0×6.
B Software Backup and Recovery Backup HP Backup and Recovery Manager provides several ways to back up the system and to recover optimal system functionality. installed drivers, utilities, and applications can be copied to ✎ HP a CD or to a DVD using HP Backup and Recovery Manager. DVD±RW discs and DVD±RW double-layer discs ✎ Formatted are not compatible with HP Backup and Recovery Manager. computer must be connected to external power before you ✎ The perform backup and recovery procedures.
Software Backup and Recovery Backing Up the System Using HP Backup and Restore Manager, you can ■ Back up specific files and folders. ■ Back up the entire system. ■ Back up modifications since your last backup, using HP system restore points. ■ Schedule backups. Backing Up Specific Files or Folders You can back up specific files or folders to the hard drive, to an optional external hard drive, or to discs.
Software Backup and Recovery Backing Up the Entire Hard Drive When you perform a complete backup of the hard drive, you are saving the full factory image, including the Windows operating system, software applications, and all personal files and folders. of the entire hard drive image can be stored on another ✎ Ahardcopydrive, on a network drive, or on recovery discs that you create. process may take over an hour, depending on your ✎ This computer speed and the amount of data being stored.
Software Backup and Recovery Backing Up Modifications Made to the System When you back up modifications since your last backup, you are creating system recovery points. This allows you to save a snapshot of your hard drive at a specific point in time. You can then recover back to that point if you want to reverse subsequent changes made to your system. first system recovery point, a snapshot of the entire image, ✎ The is automatically created the first time you perform a backup.
Software Backup and Recovery Scheduling Backups To schedule backups: 1. Select Start > All Programs > HP Backup & Recovery > HP Backup Scheduler. The “Backup Scheduler” page opens. 2. Click Next. 3. Schedule system recovery points at specific intervals (now, daily, weekly, or monthly) or at specific events, such as at system start or when you dock to an optional docking station (select computer models only), by clicking one of the available options. Click Next to further define the settings.
Software Backup and Recovery HP Backup and Recovery Manager allows you to ■ Create recovery discs (highly recommended). The recovery discs are used to start up your computer and to recover the full factory image (operating system and software) in case of system failure or instability. do not have a CD or DVD burner, a copy of the entire ✎ Ifhardyoudrive image can be stored on another hard drive or on a network drive. ■ Perform a recovery.
Software Backup and Recovery Before creating recovery discs: ■ Obtain high-quality CD-R, DVD-R, or DVD+R media, purchased separately. DVD±RW discs and DVD±RW double-layer discs ✎ Formatted are not compatible with HP Backup and Recovery Manager. ■ Number each disc before inserting it into the optical drive of the computer. ■ If necessary, you can cancel Recovery Media Creator before you have finished creating the recovery discs.
Software Backup and Recovery Performing a Recovery from the Hard Drive There are 2 ways to initiate a recovery from the hard drive: ■ From within Windows. ■ From the recovery partition. Initiating a Recovery in Windows To initiate a recovery in Windows: 1. Back up all personal files. 2. Select Start > All Programs > HP Backup & Recovery > HP Backup and Recovery Manager. 3. Click Next. 4. Click Recover important files or the entire system, and then click Next. 5.
C Display Component Recycling Å WARNING: The backlight contains mercury. Caution should be exercised when removing and handling the backlight to avoid damaging this component and causing exposure to the mercury. Ä CAUTION: The procedures in this appendix can result in damage to display components. The only components intended for recycling purposes are the liquid crystal display (LCD) panel and the backlight. Careful handling should be exercised when removing these components.
Display Component Recycling This appendix provides disassembly instructions for the display assembly. The display assembly must be disassembled to gain access to the backlight 1 and the liquid crystal display (LCD) panel 2. procedures differ from one display assembly to ✎ Disassembly another. The procedures provided in this appendix are general disassembly instructions.
Display Component Recycling Perform the following steps to disassemble the display assembly: 1. Remove all screw covers 1 and screws 2 that secure the display bezel to the display assembly.
Display Component Recycling 2. Lift up and out on the left and right inside edges 1 and the top and bottom inside edges 2 of the display bezel until the bezel disengages from the display assembly. 3. Remove the display bezel 3.
Display Component Recycling 4. Disconnect all display panel cables 1 from the display inverter and remove the inverter 2.
Display Component Recycling 5. Remove all screws 1 that secure the display panel assembly to the display enclosure. 6. Remove the display panel assembly 2 from the display enclosure.
Display Component Recycling 7. Turn the display panel assembly upside down. 8. Remove all screws that secure the display panel frame to the display panel.
Display Component Recycling 9. Use a sharp-edged tool to cut the tape 1 that secures the sides of the display panel to the display panel frame. 10. Remove the display panel frame 2 from the display panel.
Display Component Recycling 11. Remove the screws 1 that secure the backlight cover to the display panel. 12. Lift the top edge of the backlight cover 2 and swing it forward. 13. Remove the backlight cover.
Display Component Recycling 14. Turn the display panel right-side up. 15. Remove the backlight cables 1 from the clip 2 in the display panel.
Display Component Recycling 16. Turn the display panel upside down. 17. Remove the backlight frame from the display panel.
Display Component Recycling Å WARNING: The backlight contains mercury. Caution should be exercised when removing and handling the backlight to avoid damaging this component and causing exposure to the mercury. 18. Slide the backlight out of the backlight frame.
Display Component Recycling 19. Disconnect the display cable 1 from the LCD panel. 20. Remove the screws 2 that secure the LCD panel to the display rear panel. 21. Release the LCD panel 3 from the display rear panel. 22. Release the tape 4 that secures the LCD panel to the display rear panel.
Display Component Recycling 23. Remove the LCD panel. Removing the LCD Panel 24. Recycle the LCD panel and backlight.
D Connector Pin Assignments Table D-1 Audio-Out (Headphone) Pin Signal Pin Signal 1 Audio out, left channel 3 Ground 2 Audio out, right channel Maintenance and Service Guide D–1
Connector Pin Assignments Table D-2 Audio-In (Microphone) Pin Signal Pin Signal 1 Audio signal in 3 Ground 2 Audio signal in Table D-3 Universal Serial Bus Pin Signal Pin Signal 1 +5 VDC 3 Data + 2 Data – 4 Ground D–2 Maintenance and Service Guide
Connector Pin Assignments Table D-4 S-Video-Out Pin Signal Pin Signal 1 S-VHS color (C) signal 5 TV-CD 2 Composite video signal 6 S-VHS intensity ground 3 S-VHS intensity (Y) signal 7 Composite video ground 4 S-VHS color ground Maintenance and Service Guide D–3
Connector Pin Assignments Table D-5 External Monitor Pin Signal Pin Signal 1 Red analog 9 +5 VDC 2 Green analog 10 Ground 3 Blue analog 11 Monitor detect 4 Not connected 12 DDC 2B data 5 Ground 13 Horizontal sync 6 Ground analog 14 Vertical sync 7 Ground analog 15 DDC 2B clock 8 Ground analog D–4 Maintenance and Service Guide
Connector Pin Assignments Table D-6 RJ-11 (Modem) Pin Signal Pin Signal 1 Unused 4 Unused 2 Tip 5 Unused 3 Ring 6 Unused Maintenance and Service Guide D–5
Connector Pin Assignments Table D-7 RJ-45 (Network) Pin Signal Pin Signal 1 Transmit + 5 Unused 2 Transmit – 6 Receive – 3 Receive + 7 Unused 4 Unused 8 Unused D–6 Maintenance and Service Guide
E Power Cord Set Requirements 3-Conductor Power Cord Set The wide range input feature of the computer permits it to operate from any line voltage from 100 to 120 or 220 to 240 volts AC. The power cord set included with the computer meets the requirements for use in the country where the equipment is purchased. Power cord sets for use in other countries must meet the requirements of the country where the computer is used.
Power Cord Set Requirements General Requirements The requirements listed below are applicable to all countries. E–2 ■ The length of the power cord set must be at least 1.5 m (5.0 ft) and a maximum of 2.0 m (6.5 ft). ■ All power cord sets must be approved by an acceptable accredited agency responsible for evaluation in the country where the power cord set will be used.
Power Cord Set Requirements Country-Specific Requirements 3-Conductor Power Cord Set Requirements Country/Region Accredited Agency Applicable Note Number Australia EANSW 1 Austria OVE 1 Belgium CEBC 1 Canada CSA 2 Denmark DEMKO 1 Finland FIMKO 1 France UTE 1 Germany VDE 1 Italy IMQ 1 Japan METI 3 ✎ NOTES: 1. The flexible cord must be Type HO5VV-F, 3-conductor, 1.0 mm² conductor size.
Power Cord Set Requirements 3-Conductor Power Cord Set Requirements (Continued) Country/Region Accredited Agency Applicable Note Number Korea EK 4 The Netherlands KEMA 1 Norway NEMKO 1 People’s Republic of China CCC 5 Sweden SEMKO 1 Switzerland SEV 1 Taiwan BSMI 4 United Kingdom BSI 1 United States UL 2 ✎ NOTES: 1. The flexible cord must be Type HO5VV-F, 3-conductor, 1.0 mm² conductor size.
Index A accessory battery connector 1–19 arrow keys 1–15 audio troubleshooting 2–21 audio-in jack location 1–9 pin assignments D–2 audio-out jack location 1–9 pin assignments D–1 B base enclosure cover location 1–19 removal 5–35 spare part number 3–8, 3–19 base enclosure, spare part number 3–10, 3–20 battery bay 1–19 battery light 1–7 battery pack removal 5–6 spare part number 3–10, 3–20, 5–6 specifications 6–5 battery release latch 1–19 Maintenance and Service Guide Bluetooth module removal 5–12 spare p
Index left-side 1–10, 1–12 rear 1–10, 1–12 right-side 1–8 top 1–16 computer feet illustrated 3–13 locations 5–11 Computer Setup Advanced Menu 2–5 Diagnostics Menu 2–4 File Menu 2–2 overview 2–1 Security Menu 2–3 computer specifications 6–1 connector pin assignments audio-in D–2 audio-out D–1 external monitor D–4 headphone D–1 microphone D–2 modem D–5 monitor D–4 network D–6 RJ-11 D–5 RJ-45 D–6 S-Video-out D–3 Universal Serial Bus (USB) D–2 connectors, service considerations 4–2 D design overview 1–20 Digi
Index Display Rubber Screw Cover Kit, spare part number 3–12, 3–21 docking connector 1–19 drive light 1–7 drives, preventing damage 4–3 DVD±RW and CD-RW Double-Layer Combo Drive, spare part number 3–15 E electrostatic discharge 4–4, 4–8 expansion product, troubleshooting 2–14 external monitor port location 1–13 pin assignments D–4 External MultiBay II power cable and stand, spare part number 3–15, 3–18 External MultiBay II, spare part number 3–15, 3–18 F fan removal 5–24 spare part number 3–3, 3–20, 5–24
Index hard drive cover illustrated 3–13 location 1–19 removal 5–8 spare part number 3–10, 3–20 hard drive frame, removal 5–10 headphone jack location 1–9 pin assignments D–1 heat sink removal 5–25 spare part number 3–8, 3–22, 5–25 hinge saddle removal 5–65 spare part number 3–8, 3–20, 5–65 HP Docking Station 120-W AC adapter, spare part number 3–19 HP Docking Station Miscellaneous Plastics Kit, spare part number 3–15, 3–19 HP Docking Station, spare part number 3–15, 3–20 I I/O address specifications 6–9 I
Index microphone 1–7 disconnecting 5–38 illustrated 3–11 removal 5–43 spare part number 3–12, 3–21, 5–43 microphone jack location 1–9 pin assignments D–2 Mini Card WLAN module removal 5–32 spare part numbers 3–5, 3–17, 3–18, 3–19, 5–32 modem cable illustrated 3–14 removal 5–69 modem jack location 1–13 pin assignments D–5 modem module removal 5–68 spare part number 3–8, 3–21, 5–68 troubleshooting 2–26 monitor port location 1–13 pin assignments D–4 MultiBay DVD/CD-RW Combo Drive, spare part number 3–15, 3–18
Index power management features 1–5 power supply, spare part number 3–16, 3–20 power switch 1–11 power, troubleshooting 2–8 presentation button 1–17 processor removal 5–28 spare part numbers 3–8, 3–19, 3–22, 5–28 R rear components 1–10, 1–12 rear keyboard cover removal 5–53 spare part number 3–3, 3–20, 5–53 removal/replacement preliminaries 4–1 procedures 5–1 right-side components 1–8 RJ-11 jack location 1–13 pin assignments D–5 RJ-45 jack location 1–13 pin assignments D–6 RTC battery removal 5–70 spare p
Index modem 2–26 network 2–26 nonfunctioning device 2–14, 2–23 OS loading 2–15 overview 2–1 pointing device 2–25 power 2–8 video 2–12 system DMA 6–6 system memory map 6–12 T thermal paste, replacing 5–27, 5–66 thermal shield removal 5–65 spare part number 3–8, 3–22, 5–65 tools required 4–1 top components 1–16 top cover removal 5–51 spare part number 3–3, 3–22, 5–51 TouchPad location 1–17 removal 5–55 spare part number 3–3, 3–22, 5–55 TouchPad bracket, removal 5–57 TouchPad buttons 1–17 TouchPad cable, di
