HP Installation Guide, HP AT094A PCIe 2P 8Gb FC and 2P 1/10GbE Adapter Abstract This document is for the person who installs, administers, and troubleshoots servers and storage systems. HP assumes you are qualified in the servicing of computer equipment and trained in recognizing hazards in products with hazardous energy levels.
© Copyright 2011, 2012 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
Contents 1 Introduction...............................................................................................5 Overview................................................................................................................................5 LED indicators..........................................................................................................................5 Network management..................................................................................................
8 Acronyms and abbreviations......................................................................23 Acronyms and abbreviations....................................................................................................23 Index.........................................................................................................
1 Introduction Overview The HP AT094A PCIe 2P 8Gb FC and 2P 1/10GbE Adapter is a dual port 8Gb FC and 1/10GbE adapter for the HP Integrity rx2800 i2 and Superdome2 systems. The HP Product number is AT094A. These two descriptions refer to the same device and are used interchangeably throughout this document. The AT094A adapter uses the BladeEngines 3 (BE3) Emulex chip that provides 10 Gigabit Ethernet functionality and the Emulex 8 Gigabit Fibre Channel Controller.
Table 1 AT094A Networking LED indicators Yellow LED Green LED State Off Off Wake-up failure (Dead board) On Off POST failure (Dead board) Slow Blink Off Wake-up failure monitor Table 2 AT094A Fibre Channel LED indicators Yellow LED Green LED State Fast Blink Off POST failure Flashing Off POST processing in progress Off On Failure while functioning On On Failure while functioning 2 Fast Blinks On 2Gb Link rate – Normal, link up 3 Fast Blinks On 4Gb Link rate – Normal, link up
2 Installing an adapter IMPORTANT: See the following chapter before installing the AT094A adapter: “Installing the HP-UX operating system components” (page 9) Preventing electrostatic discharge To prevent damaging the system, be aware of the precautions you need to follow when setting up the system or handling parts. A discharge of static electricity from a finger or other conductor may damage system boards or other static-sensitive devices. This type of damage may reduce the life expectancy of the device.
NOTE: The two ports closest to the PCIe edge connector (bottom two as in Figure 1 (page 5)) are the Networking ports. The two ports away from the PCIe edge connector (top two) are the Fibre Channel ports. 5. Do not power on the system until the following section is complete: “Attaching the adapter to other Fibre Channel devices” (page 8) Connecting the network cables The AT094A has two LC ports. These ports support either of the following: • Direct Attached Copper (DAC) cables.
3 Installing the HP-UX operating system components HP-UX operating system The HP AT094A PCIe 2P 8Gb FC and 2p 1/10GbE adapter is supported through the HP-UX 11i v3 operating system. Prerequisites Before installing the adapter, follow these steps: 1. The adapter card is supported through the HP Integrity rx2800 i2 and Superdome2 server platforms.
4.
Installing driver software Use the following instructions if the drivers are provided on a CD-ROM. If the driver software is downloaded, follow the instructions provided with that file. Ethernet NOTE: The initial release of the 10GigEthr-03 bundle is available by restricted download only; please contact your account manager or HP-UX Ambassador for instructions on how to obtain this bundle.
Installing OnlineDiag Failure to properly complete the steps in this procedure may result in erratic system behavior or system failure and may void the warranty. For assistance with this procedure, contact your local HP Authorized Service Provider. Install OnlineDiag, which is available at the Software Depot website: https://h20392.www2.hp.com/portal/swdepot/index.do OnlineDiag is also available from the IPF CD for Itanium®-based systems. Verify the Ethernet adapter installation 1.
1. Enter the following command: ioscan -kfnC fc 2. Verify that the correct drivers appear for each installed adapter.
Alternate website for downloading files 1. See the following HP website: http://www.hp.com/#Support 2. 3. 4. 14 You can click open the Support & Drivers link or enter your adapter product number in the SEARCH HP.COM field, then click go. For example, type AT094A. At the next web page, either locate the Software & driver downloads link to continue search or view the returned listing for your selected product. Download the drivers, firmware, or documentation as needed.
4 Specifications Cable specifications Table 3 Cable specifications SFP+ module type 10GBASE-SR (short range) Optical Module 10GBASE-CR with Direct Attached Copper (DAC) cable Cable grade Minimum modal bandwidth (MHz-km) Maximum cable length (meters) 62.5 (“FDDI”) 160 26 62.
Table 5 Compliance (continued) Compliance Standard CE SFF-8431- 10 Gigabit Small Form Factor Pluggable Module “SFP+” IPv4/IPv6 TCP, UDP checksum Offload IPv4/IPv6 TCP, Large Send Offload IPv4/IPv6 TCP, Large Receive Offload Jumbo Frames up to 9000 Bytes Power and environmental specifications Table 6 Power and environmental specifications Power and environmental specifications Value Operating Temperature 0° to 55° C (32° to 131° F) Humidity 15 to 80% relative humidity (RH), non-condensing Non-operating
5 Regulatory compliance notices Regulatory compliance identification numbers For the purpose of regulatory compliance certifications and identification, this product has been assigned a unique regulatory model number. The regulatory model number can be found on the product nameplate label, along with all required approval markings and information. When requesting compliance information for this product, always refer to this regulatory model number.
Figure 2 Class 1 laser product label This optional label indicates that the product is classified as a CLASS 1 LASER PRODUCT. This label may appear on the laser device installed in your product. International notices and statements Canadian notice (avis Canadien) Class A equipment This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
BSMI notice Figure 3 BSMI notice Japanese notice Figure 4 Japanese notice Korean notices Figure 5 Korean notices BSMI notice 19
Declaration of conformity 20 Regulatory compliance notices
6 Electrostatic Discharge Electrostatic Discharge To prevent damage to the system, be aware of the precautions you need to follow when setting up the system or handling parts. A discharge of static electricity from a finger or other conductor may damage system boards or other static-sensitive devices. This type of damage may reduce the life expectancy of the device.
7 HP Contact information HP contact information For the name of the nearest HP authorized reseller: • See the following Contact HP worldwide (in English) webpage: http://welcome.hp.com/country/us/en/wwcontact_us.html For HP technical support: • In the United States, for contact options see the Contact HP United States webpage: http://welcome.hp.com/country/us/en/cs/home.html. To contact HP by phone: ◦ Call 1-800-HP-INVENT (1-800-474-6836). This service is available 24 hours a day, 7 days a week.
8 Acronyms and abbreviations Acronyms and abbreviations 10GbE 10 Gigabit Ethernet CSA Canadian Standards Association IEEE Institute of Electrical and Electronics Engineers LED Light emitting diode OS Operating System PCI Express Peripheral Component Interconnect Express RoHS Restriction of Hazardous Substances SFP small form-factor pluggable Acronyms and abbreviations 23
Index 10GbE, 23 LC, 15 LED, 23 LEDs, 5 A O Adapter LEDs, 5 adapters, 5 OS, 23 B PCI Express, 7, 23 power specifications, 16 preventing electrostatic damage, 21 Symbols bracket, 7 bracket, low profile, 7 BSMI, regulatory compliance notice, 19 C cable specifications, 15 certification and classification information, laser, 17 Class A equipment, Canadian compliance statement, 18 compliance, 15, 17 contact information, 22 CSA, 23 D downloading files, 14 E electrostatic damage prevention, 21 electrost
