HP Designjet High Speed Dryer 104 inch User's guide
Legal notices The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statement accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
Table of contents 1 Introduction Safety precautions ........................................................................................................................... 1 Warnings .................................................................................................................. 1 Cautions ................................................................................................................... 2 Handling precautions ...........................................................
B. Limitations of liability .......................................................................................... 24 C. Local law ............................................................................................................ 25 Regulatory notices ......................................................................................................................... 26 Regulatory Model Number ......................................................................................
Introduction Introduction 1 Thank you for purchasing the HP Designjet High Speed Dryer - 104 inch (hereafter called the dryer). The dryer is used near the printer's paper outlet to dry the ink printed on the paper efficiently. The dryer helps the printer to maximize its high-speed printing capability. Features of the dryer: ● Quick dry in response to high-speed printing Dries the paper by warm air from the paper outlet which is the paper path from the printer to the winding unit.
Introduction ● Do not damage, break, process, or heat the power cable. Using a damaged power cable may cause fire or electric shock. ● Do not remove the covers attached to the dryer because they contain high-voltage and extremely hot parts. Careless removal might result in an electric shock or burn. ● Never use the dryer in a place of extreme humidity or any place where it can possibly be splashed by any liquids.
The dryer operates on 180-253 V, 50/60 Hz AC power, single-phase. Ensure that the power outlet meets the voltage and current requirements of the dryer. See Specifications for details. ● Do not connect a number of cables to a single socket. The dryer should be connected to a single outlet. Introduction ● Dryer ● Do not place things or lean on the dryer. ● Do not wipe the cover with benzene or thinner. The coating may peel off or discolor. Wipe the surface of the cover lightly with a soft cloth.
Introduction 4 Chapter 1 Introduction ENWW
2 How to assemble the dryer How to assemble the dryer Please read the assembly instructions closely in order to assemble the dryer correctly. Before assembly The dryer package contains the parts shown below. Make sure that all parts are present before starting to assemble them. 1. Dryer unit 2. Support stay 3. Foot with castor (2) 4. Stand (2) 5. M5×12L hexagon socket head bolt (16) 6. Hexagon bar wrench 7.
How to assemble the dryer 2. Secure a foot (3) to each stand (1) with the hexagon socket head bolts (2). 3. Place the dryer unit (1) on the protective sheet with its air outlet face up. 4. Remove knobs (3) (two at each side) from both ends of the dryer unit (1). NOTE 6 Do not remove the washers (2) from the dryer (1).
Secure the stands (1) to the dryer unit (2) with the knobs (3) (two at each side) as shown below. How to assemble the dryer 5. NOTE Attach the stands in such a way that the operation panel (4) on the dryer unit will be face up when the dryer is raised into its standing position. Attach the stands in such a way that the holes in the stands face inwards; they will be used to attach the support stay. 6.
7. Secure the support stay (1) with four hexagon socket head bolts (2) at each side of the dryer unit. Check that all screws are tightly fastened.
3 How to install the dryer Installation space How to install the dryer The following diagram shows the printer (1), the dryer (2), and the free space that should be left around the dryer in millimeters. The height of the dryer is 870 mm. The dryer should be positioned at least 50 mm (1) from the paper emerging from the printer (4), with the air inlet (6) and outlet (3) positioned as shown below. The air inlet (6) should also be at least 300 mm (2) from any obstruction (5).
2. Open the power cable clamp, pass the power cable through the clamp, close the clamp, and then clamp the cable. This prevents accidental unplugging. 3. Confirm that the dryer's main power switch is off (O), then connect the other end of the power cable to a suitable power outlet (see Specifications for details). 4. Turn on the dryer's main power switch.
4 Dryer components Main external components Dryer unit 2. Warm air outlet 3. Operation panel 4. Power switch 5. AC inlet 6. Stand 7. Castor Dryer components 1.
Operation panel components 1. 2. ● Indicates the remaining time on the timer. ● Press Timer buttons (5) up or down to set the timer (from the minimum one hour to maximum 24 hours). Power button: ● Turns the dryer on or off. ● If the Power button is turned off while the heater is operating, the fan continues to operate for three more minutes before the dryer eventually turns off. 3. Fan button: When switched on, air is blown out of the dryer. 4.
9. Air flow lamp indicates the air flow from the fan at three levels: High (H), Medium (M) and Low (L). 10. Heater Error lamp: This is lit when the temperature of the top cover is too high. CAUTION When the Heater Error lamp comes on, press the heater button to stop warm air operation, and blow air at the maximum flow level (H) for 10 minutes to cool the inside of the dryer. After the dryer cools down, turn off the dryer using the main power switch, then contact our service center.
Dryer components 14 Chapter 4 Dryer components ENWW
How to use the dryer 5 How to use the dryer Basic operating procedure 1. Press the Power button (2) to switch on the dryer (the operation panel and air flow lamp come on). 2. Press the Heater button (4) to set the operation mode (the Fan lamp (7) and the Heater lamp (8) will come on). 3. ● If the Fan button (3) has been pressed before the Heater button (4), you will not be able to turn on the heater by pressing the Heater button (4).
How to use the dryer CAUTION weight. Do not sit on the dryer or lean heavily on it. It is not strong enough to support your Do not turn off the main power switch until the fan has finished its three-minute cooling-off period after the heater stops. When the main power switch is turned off, the fan stops turning, resulting in an increase in internal temperatures due to the remaining heat of the heater. This may damage the dryer. In addition heated surface may cause burns.
How to use the dryer When room temperature is low Always turn on the heater to keep air from the dryer at room temperature +10 to 20 °C. Raising the temperature to a certain level is required to dry the printed paper. Room temperature should be kept at 20 °C or more to increase drying efficiency. Paper setting with or without the take-up-reel unit Paper settings with or without the take-up-reel unit are shown below.
How to use the dryer 18 Chapter 5 How to use the dryer ENWW
6 Maintenance and cleaning Maintenance and cleaning Maintenance The dryer should be inspected periodically for defects. If defects are found, they can be repaired by onsite service or, if necessary, at a service center. Cleaning If the surface of the dryer becomes extremely dirty, you can wipe it with a soft cloth dipped in water and neutral detergent and squeezed tightly. CAUTION Turn off the dryer's power switch before cleaning.
Maintenance and cleaning 20 Chapter 6 Maintenance and cleaning ENWW
Specifications Item Specification Dimensions 3310 (W) x 610 (D) x 870 (H) mm Weight 60 kg or less Color Carbonite Black Maximum paper width 2600 mm Heater type Sheathed heater Warm-up time 10 minutes or less Paper path Winding or straight output Warm air temperature Ambient temperature + 10°C or more Fan flow control Three levels: High, Medium or Low Timer Range: 1 to 24 hours (unit: 1 hour) Specifications 7 (Error: ± 1%/h) Acquired regulations and standards EN55022 Class A FCC Par
Item Specification Inrush current 35 A or less Grounding D class grounding (The 3rd class grounding) Operating temperature and humidity range Temperature: 15 to 30°C Humidity: 30 to 70%RH (no condensation) Storage temperature and humidity range Temperature: 5 to 35°C Humidity: 10 to 80%RH (no condensation) Dust level Equivalent to office environments. Ventilation Ventilation facilities are recommended for deodorization.
8 Legal information Limited Warranty—HP Designjet High Speed Dryer - 104 inch HP product Limited Warranty Period Hardware product 1 year from the date of hardware’s purchase by the customer 1. This Hewlett-Packard (HP) Limited Warranty gives you, the end-customer, express limited warranty rights from HP. In addition, you may also have other legal rights under the applicable local law or special written agreement with HP. 2.
5. Your exclusive remedies for defective HP products are the following: a. During the Limited Warranty Period, HP will replace any defective HP consumable product that is covered by this Limited Warranty, and deliver another product to you to replace the defective one. b. During the Limited Warranty Period, HP, at its sole discretion, shall either repair on site or replace any defective hardware product or component part.
C. Local law 1. This Limited Warranty gives you specific legal rights. You may also have other rights which vary from state to state in the United States, from province to province in Canada, and from country to country elsewhere in the world. You are advised to consult applicable state, province, or national laws for full determination of your rights. 2.
Regulatory notices Regulatory Model Number For regulatory identification purposes, HP has assigned a Regulatory Model Number (RMN). The Regulatory Model Number for your product is as follows: RMN Product family BCLAA-0607 HP Designjet High Speed Dryer - 104 inch The Regulatory Model Number (RMN) should not be confused with the marketing name (HP Designjet High Speed Dryer - 104 inch) or product number. Regulatory statements Europe WARNING! This is a class A product.
Canada Normes de sécurité (Canada) Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de Classe A prescrites dans le réglement sur le brouillage radioélectrique édicté par le Ministére des Communications du Canada. DOC statement (Canada) This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications.
Germany Sound Geräuschemission (Germany) LpA < 70 dB, am Arbeitsplatz, im Normalbetrieb, nach DIN45635 T. 19.
Additional information The product herewith complies with the requirements of the Low-Voltage Directive 73/23/EEC and the EMC Directive 89/336/EEC, and carries the CE marking accordingly. 1. The product was tested in a typical configuration with HP Personal Computer Systems and peripherals. 2. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 3. ● This device may not cause harmful interference.
Legal information 30 Chapter 8 Legal information ENWW
