Turset.
Turset.book Page 2 Monday, April 19, 1999 6:12 PM All rights are reserved. No part of this document may be photocopied, reproduced, or translated to another language without the prior written consent of HewlettPackard Company. PostScript® is a registered trademark of Adobe Systems Incorporated. Notice The information contained in this document is subject to change without notice and should not be construed as a commitment by Hewlett-Packard Company.
Turset.
Turset.book Page 4 Monday, April 19, 1999 6:12 PM Upgrading your Printer Before installing your take-up reel, you should check that the firmware module installed in your printer supports a take-up reel. Checking the Firmware Revision Number Utilities Statistics Code rev You can find out your firmware revision number from the printer’s front panel by selecting the Printer Setup menu and then “Utilities”, “Statistics”, and “Code rev”. ■ If your firmware revision number is A.01.
Turset.book Page 5 Monday, April 19, 1999 6:12 PM Installing a New Firmware Module This section explains how to install a new firmware module. If you do not need to install a new firmware module (see the previous page), you can skip this section. CAUTION The firmware module contains electrical components that are easily damaged by small amounts of static electricity.
Turset.book Page 6 Monday, April 19, 1999 6:12 PM 3 Switch the printer off at the power isolator switch at the back of the printer and disconnect the power cord and the interface cable. 2 1 Power Cord Power Off the Printer 4 Unscrew the four screws and remove the cover plate at the back of the printer. To prevent loss of these screws, loosely re-install them in the printer.
Turset.book Page 7 Monday, April 19, 1999 6:12 PM 5 Looking at the back of the printer, you will see three slots. It is important to install the firmware module in the slot that is furthest to the right. 6 Put on a grounding wrist strap and attach the other end to the metal chassis of the printer. 7 Remove the module that is currently occupying the rightmost slot. First push down the lower locking tab to release the module, then pull out the module, holding it by its edges.
Turset.book Page 8 Monday, April 19, 1999 6:12 PM 9 Carefully push the top edge of the firmware module into the slot. 10 Continue pushing the top edge of the firmware module until you feel it “click” into position. At the same time you will see that the top locking tab locks into position.
Turset.book Page 9 Monday, April 19, 1999 6:12 PM 11 Carefully push the bottom edge of the firmware module into the slot until you feel it “click” into position. Again, you will see that the bottom locking tab locks into position. 12 Remove the grounding wrist strap and then re-install the cover plate on the back of the printer, using the four screws.
Turset.book Page 10 Monday, April 19, 1999 6:12 PM 13 Re-install the paper path deflector on the left side of the printer. 2 1 14 Reconnect the power cord and the interface cable and switch on the power isolator switch at the back of the printer. 1 Power Isolator Switch Power Cord You have now finished installing the firmware module.
Turset.book Page 11 Monday, April 19, 1999 6:12 PM Take-Up Reel Components These are the main components of the take-up reel.
Turset.
Turset.book Page 13 Monday, April 19, 1999 6:12 PM Installing the Take-Up Reel 6. Carefully lever the six retaining clips from the paper-bin support. Device Setup TUR installed 1. Using the front panel, select the Printer Setup menu, then “Device Setup”, then “TUR installed”, and change the value of this option from No to Yes. If you do not find any “TUR installed” option, you may need to upgrade your printer’s firmware (see Upgrading your Printer, on page 4). 2.
Turset.book Page 14 Monday, April 19, 1999 6:12 PM 8. Remove the six paper-bin arms. 2 1 11. Release the clamp on the left-hand assembly by loosening the screw shown below. Do not remove the screw. 9. Remove the bin support from the legs assembly by removing four screws. Do not use these (shorter) screws for the next step. 10. Install the four (longer) screws from the takeup reel kit loosely into the legs as shown below. Do not tighten them yet.
Turset.book Page 15 Monday, April 19, 1999 6:12 PM 12. Open the clamp and fit the left-hand assembly 14. Close the clamp and secure with the clamp on to the screws installed in step 10. screw as shown below. 13. Pull the left-hand assembly down so that it rests securely on the screws. 15. Tighten the two screws supporting the assembly. 16. Release the clamp on the right-hand assembly. by loosening the screw shown below. Do not remove the screw.
Turset.book Page 16 Monday, April 19, 1999 6:12 PM 17. Open the clamp and fit the right-hand assembly on to the screws installed in step 10. 19. Close the clamp and secure with the clamp screw as shown below. Clamp Clamp screw 18. Pull the right-hand assembly down so that it rests securely on the screws. HP DesignJet 1000 Series Take-Up Reel 20. Tighten the two screws supporting the assembly. 21. Unscrew the screw on the sensor assembly shown below (but do not remove it) and open the clamp.
Turset.book Page 17 Monday, April 19, 1999 6:12 PM 22. Install the front of the sensor assembly onto 24. Slide the sensor assembly hard up against the the front of the right foot assembly as shown below leg and then close the sensor clamp as shown below. Sensor assembly 25. Tighten the screw to secure the clamp in place and connect the sensor cable as shown below. Right foot assembly 23. Lower the sensor into the position shown below.
Turset.book Page 18 Monday, April 19, 1999 6:12 PM 26. Connect the power cord into the rear of the take-up reel. 29. Ensure the spindle lock is open. Power switch 27. Use the blue lever to unlock the left-hand paper guide on the take-up reel spindle. Remove the paper guide. 30. Install the take-up reel spindle into the printer by pushing firmly on each end of the spindle A then 28. Assemble the take-up reel core and put it on to B as shown below. the spindle as shown below.
Turset.book Page 19 Monday, April 19, 1999 6:12 PM 31. 33. Slide each of the deflector supports sideways until the T-piece on top of the support is fully You must close the spindle lock, otherwise the takeinserted into the gap between the cross brace and the up reel will not operate. printer leg. The deflector support should now be touching the take-up reel assembly. IMPORTANT: Close the spindle lock. 12'' / 30 5m m 34. 32.
Turset.book Page 20 Monday, April 19, 1999 6:12 PM 35. Attach it to the supports with the two screws provided. 36. Turn on the take-up reel by pressing the switch at the back. 37. If you have disconnected the printer’s power cord, re-connect it now, turn on the power isolator switch at the back of the printer, then turn on the printer using the on/off button on the front panel. 38. Wait until the printer has finished initializing and a “Ready” message is displayed on the front panel.
Turset.book Page 21 Monday, April 19, 1999 6:12 PM Loading Paper on to the Take-Up Reel Before using the take-up reel, ensure that it has been properly installed (see preceding pages). In particular, the core tube should be mounted on the spindle. CAUTION HP Bright White Inkjet Paper is available in 150-ft and 300-ft rolls. The takeup reel can only completely roll up 150-ft rolls. CAUTION Backlit paper with a separate slip sheet is not recommended for use with the take-up reel.
Turset.book Page 22 Monday, April 19, 1999 6:12 PM 2 Ensure that the spindle lock is closed. 3 Move the adjustment levers on the left and right paper guides to the unlocked position.
Turset.book Page 23 Monday, April 19, 1999 6:12 PM 4 The two paper guides and core must be positioned on the take-up reel spindle so that the paper is in the center, between the paper guides. Adjust the position of the core as shown below. The paper guides may be slightly stiff on the spindle: you may have to use both hands. 5 When you have adjusted the position of the core, pull the adjustment levers on both paper guides to the locked position.
Turset.book Page 24 Monday, April 19, 1999 6:12 PM 6 Pull the paper taut to the position shown below. Do not attempt to pull more paper out of the printer; if you need more paper, use the front panel.
Turset.book Page 25 Monday, April 19, 1999 6:12 PM 7 Use a small amount of sticky tape to attach the paper to the core. Use three strips, one in the middle (first) and then one at each side of the paper. NOTE: Use only tape that will not tear the paper when it is removed later. NOTE: To avoid the paper skewing as it is wound onto the core tube, ensure the paper is straight when it is attached. 8 Press the ↓ key on the front panel to advance the paper.
Turset.book Page 26 Monday, April 19, 1999 6:12 PM 9 Important: Press the paper wind button on the take-up reel panel indicated below to wind the paper once around the core. If the paper fails to wind, ensure that the spindle lock is closed (see step 2) 10 Press the ↓ button on the front panel to advance some more paper: enough to enable you to insert the paper weight. It is important that the paper weight is the same width as the paper you are using.
Turset.book Page 27 Monday, April 19, 1999 6:12 PM 11 Carefully insert the paper weight. Ensure that the end caps are installed and extend over the edges of the paper. CAUTION It is important that the paper weight is inserted. The take-up reel will not function properly without it. m 67m / 10 5mm m ''/91 = 36 /1270m '' + 0 mm 5 = 372 /1 + '' = 54 + 42'' 5mm / 30 12'' 12 Press Enter on the printer’s front panel, which will then display the Ready message.
Turset.book Page 28 Monday, April 19, 1999 6:12 PM 13 Shown below is how the printer should look when it is in operation. As paper is fed from the printer it drops down in a loop and up into the take-up reel spindle.
Turset.book Page 29 Monday, April 19, 1999 6:12 PM Unloading Paper from the Take-Up Reel To unload the roll paper from the take-up reel, perform the following procedure. 1 Ensure that the ink is dry. See Drying Time with the Take-Up Reel (page 36). 2 Press the FORM FEED AND CUT key on the front panel. The front panel will prompt you to remove the paper weight and wind excess paper using the take-up reel buttons. 3 Important: Remove the paper weight as shown below.
Turset.book Page 30 Monday, April 19, 1999 6:12 PM 4 Press the paper wind button shown below to wind the paper hanging down onto the take-up reel. 5 Press Enter on the printer’s front panel. The printer will now cut the paper. 6 Slide open the spindle lock on the right-hand side of the take-up reel.
Turset.book Page 31 Monday, April 19, 1999 6:12 PM 7 Remove the take-up reel spindle. mm ' / 305 12' m 7m mm ' / 106 0mm 42' = 36''/915 /127 2mm + + + = 50'' /137 = 54'' 8 Unlock and remove the left-hand paper guide from the take-up reel spindle. Remove the core from the spindle. Take-up reel spindle Take-Up Core (with paper) Paper guide To remove roll paper from the printer, see the User’s Guide.
Turset.book Page 32 Monday, April 19, 1999 6:12 PM Changing the Core Tube on the Take-Up Reel The core tube on the take-up reel must be the same width as the paper you are using. To change the core, perform the following procedure. 1 Slide open the spindle lock on the right hand side of the take-up reel. 2 Remove the take-up reel spindle from the printer as shown by pulling firmly on each end of the spindle, A then B.
Turset.book Page 33 Monday, April 19, 1999 6:12 PM 3 Remove the left-hand paper guide. 4 Remove the old take-up core. 5 Install the new core you have chosen onto the spindle and re-install the left hand guide assembly. NOTE: You can also use an empty cardboard tube to replace the plastic take-up core that was supplied with your printer. It is important that the take-up core is the same width as the paper you are using.
Turset.book Page 34 Monday, April 19, 1999 6:12 PM NOTE: If you want to use a three-inch cardboard core, use the three-inch core adaptors shown below.
Turset.book Page 35 Monday, April 19, 1999 6:12 PM 6 Install the take-up reel spindle into the printer by pushing firmly on each end of the spindle, A then B. mm ' / 305 12' m 7m / 106 915mm 42'' = 36''/ 1270mm 2mm + + + = 50''/ 137 = 54''/ 7 Slide shut the spindle lock on the right-hand side of the take-up reel.
Turset.book Page 36 Monday, April 19, 1999 6:12 PM Drying Time with the Take-Up Reel If the ink is not dry when the paper is wound on to the take-up spindle, then the image will be damaged. In most cases the take-up reel paper loop gives the print time to dry before it is wound on to the spindle. However, sometimes the print will need a longer time to dry, and so the printer will slow down the printing process to allow more time before winding on to the take-up reel; this is called the drying time.
Turset.book Page 37 Monday, April 19, 1999 6:12 PM Drying time=Automatic This is the default setting. If necessary, the printer will automatically adjust the drying time depending on the following: ■ Type of paper ■ Print mode ■ Width of printing area ■ Environmental conditions CAUTION To avoid the printer adding drying time to prints, operate the printer under the following environmental conditions. This table applies to Best mode only.
Turset.book Page 38 Monday, April 19, 1999 6:12 PM Troubleshooting This page lists some possible explanations of problems that may occur with the take-up reel. Take-Up Reel Does Not Function ■ Perhaps you have a power problem. Check that the power cable is connected and that there is power available at the socket. ■ Check that the ON/OFF switch is in the ON position at the back of the take-up reel. ■ Check the spindle lever: it should be closed.
Turset.book Page 39 Monday, April 19, 1999 6:12 PM Take-Up Reel Specifications Paper Types Plain Paper HP Translucent Bond HP Bright White Inkjet Paper (up to 150 feet/45 meters) HP Vellum HP Coated Paper HP Heavy Coated Paper HP High-Gloss Photo Paper HP Matte Film HP Clear Film HP Natural Tracing Paper Thin natural tracing paper (more than 70 g/m2) Power Specifications Source 100-240V ac ±10%. Autoranging. Frequency 50-60 Hz Current 0.
Turset.book Page 40 Monday, April 19, 1999 6:12 PM EMC (ElectroMagnetic Compatibility) Specifications Canada Canadian Department of Communications, Radio Interference Regulations Class B compliant. European Union 89/336/EEC EMC Directive compliant. South Africa SABS licensed. USA Federal Communications Commission. Class B digital device.
Turset.book Page 41 Monday, April 19, 1999 6:12 PM Regulatory Notices Sound Geräuschemission (Germany) LpA < 70 dB, am Arbeitsplatz, im Normalbetrieb, nach DIN 45635 T. 19. Electro-Magnetic Compatibility (EMC) FCC Statements (U.S.A.) The U.S. Federal Communications Commission (in 47 cfr 15.105) has specified that the following notices be brought to the attention of users of this product.
Turset.book Page 42 Monday, April 19, 1999 6:12 PM The user may find useful the following booklet prepared by the FCC: “How to Identify and Resolve Radio-TV Interference Problems”. This booklet is available from the US Government Printing Office, Washington, DC 20402, Stock No. 004000-00345-4.
Turset.book Page 43 Monday, April 19, 1999 6:12 PM Declaration of Conformity DECLARATION OF CONFORMITY according to ISO/IEC Guide 22 and EN 45014 Manufacturer’s Name: Manufacturer’s Address: Declares that the product Product Name: Model Number (s): Product Accessory: Hewlett-Packard Espanola S.A. Barcelona Division Avda.
Turset.book Page 44 Monday, April 19, 1999 6:12 PM © Copyright Hewlett-Packard Company 1999 Part number: C6079-90001 First edition Printed in Europe Hewlett-Packard Company Barcelona Division Avda.
