Printing Specifications Product: HP Designjet 4500 Scanner Assembly Instructions Part number: Q1277-90031 EN TEXT PAGES Page Count Paper Type Ink Coverage COVER PAGES Page Count Paper Type Ink Coverage Finish 10 (5 front and 5 back) HP standard 50# book (69 to 80g/m2) recycled offset or equivalent 4-color process (CMYK) 4/4 N/A N/A N/A N/A N/A FINISH Page Trim Size A3 Bindery Staple top left corner Folding Instruction None: but poster is normally placed in a protectiveclear bag.
HP Designjet 4500 Scanner Box contents Box Box Assembly Instructions ©2005 Hewlett-Packard Company. Reservados todos los derechos. Inkjet Commercial Division Avenida Graells, 501 08174 Sant Cugat del Vallès Barcelona, España EN Q1277-90031 1. 2. 3. 4. 5. Maintenance sheet Media guides (X2) Plastic dust cover A2 envelope Scanner 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24.
1 L R Left leg 2 3 4 Turn the left and right legs upside down, and attach the feet and wheels to the legs. Use five M5X14 screws, and two wheels for each foot. Lay one of the legs down and attach the lower bar, hooking in the tab and fixing with three M5X14 screws. Attach the lower bar to the other leg, hooking in the tab and fixing with three M5X14 screws. Right leg Longer part towards the front R L Using the letter symbols shown, identify the left and right legs using the above image.
9 10 Slide the touch screen bracket assembly down over the 4 screws. Tighten the 4 screws. 13 14 11 12 Slide the keyboard table onto the touch screen arm. Push the keyboard table down until the the pointer on the touch screen arm. 15 16 C Earth cable Place some packaging boxes, or something about half the height of the scanner stand in front of the stand, and lift the scanner up onto them.
17 18 19 20 Remove the protective foam ends, and slide the hub of the touch screen assembly into the touch screen arm. Connect the earth cable from the touch screen assembly to the touch screen arm using a M5X14 screw and starwasher. Unfold the bin. From the back of the stand, insert the left and right arms of the bin into the two slots on the rear of the legs. Make sure they are fully inserted. Place the keyboard onto the keyboard table. 21 22 23 24 Cleaning the scan area...
25 26 27 28 Dry the glass fully using a separate clean, dry lint-free cloth like the one provided with the maintenance kit. Clean the white background plate with a lint-free cloth and a mild, streak-free, glass cleaner. Clean the transport rollers and surrounding area. caution: see note in step 23 Clean the glass with a lint-free cloth and a mild, streak-free, glass cleaner. 29 30 31 32 Keep out dust and reduce maintenance time Cover your scanner with the plastic dust cover when not in use.
33 34 35 36 Remove the cover on the side of the scanner, and insert one of the FireWire cables through the slot at the back. Insert the other end of the FireWire cable into one of the sockets in the scanner, and replace the cover on the side of the scanner. Fit the protected part of the bundle cable coming from the screen into two large clips. Attach the clips to the holes in the underside of the touch screen bracket.
41 42 43 44 Camera alignment & calibration (height alignment, stitching, basic calibration, and color calibration) Replace the cover onto the leg. 45 Connect the power cable extension, and then connect to a power outlet. 46 You are now required to calibrate the scanner. For this you will need the scanner maintenance sheet, found in the protective folder shown above. 47 Switch on the scanner and leave it to warm up for some minutes until the green (ready status) light appears.
49 50 51 52 The maintenance wizard will ask you to insert the maintenance sheet. The sheet’s printed side must be face down. Feed the paper in aligning the two midpoint arrows. Press ‘Next’ to continue. Now follow the instructions that appear on the touch screen. When the maintenance procedure has completed, remove the scanner maintenance sheet and return it to its protective cover. Store the folder in the slot at the front of the stand.
57 58 Next, you should check the TCP/IP settings in your touch screen, and correct them if necessary. If you intend to scan to the network, with the HP Designjet scan software, files to be shared across the network should be placed in the D:\images directory. To add an HP Designjet printer to the printer list in your scanner software, follow these steps: Once a files is saved to this directory it can be accessed through the network, from any computer with any operating system.
Hewlett Packard Company Avenida Graells, 501 08174 Sant Cugat del Vallés Barcelona Spain © Hewlett-Packard Company, 2005 Printed in Imprimé en Stampato in
