HP Designjet H35000/H45000 Printer series Release Notes
Update instructions Update instructions The printer embedded software is updated by copying the new version from the RIP to the printer. 1. Make sure the printer is online. 2. Wait until the printer has finished printing. 3. If you are using the Caldera or Onyx RIPs, configure and load media before proceeding to the next step. 4. Locate the update file DJHxxxxx.BIN (on disc provided by your reseller or downloaded from the HP web site at www.hp.
Version 4.00 Version 4.00 • NEW Production Plus mode — this is a 600x600 dpi print mode that uses an additional print pass compared to 600x600 Production print mode. This may help to improve images with heavy ink coverage in Production mode. (Note: In this mode, the Jet Out Lines pattern will have a blank section near the top of the pattern.
Version 4.
Version 4.00 Menu Tree Version 4.00 Menu Tree New Option = item added since version 2.04 Old Option = item deleted since version 2.
HP Customer Care Centers HP Customer Care Centers For service and support, contact your local reseller, who can provide prompt and personalized support.
Version 2.04 Version 2.04 • Top gutter additions, corrections — the factory now enters the printer’s serial number into the printer’s memory. This enables the serial number to be printed in the top gutter legend of printed output. The direction of printing in unidirectional mode now appears in the top gutter. Sharp Edge mode was being indicated twice in the top gutter; this version removes the second occurrence.
Version 2.03 Version 2.03 This version fixes a bug that caused the shutter aperture settings to not work as expected when printing in Sharp Edge mode. Version 2.02 • NEW Service Station Vacuum Warning Level — you can now set the level at which the warning to empty the service station vacuum reservoir will appear. The level ranges from 3.75 liters (approximately 1.0 gallons) to 11.25 liters (approximately 3 gallons) in 250 ml increments. When you increase this setting, more time elapses between warnings.
Version 2.0 • Media leading edge found on the right side — when measuring the media, the leading edge is found on the right side (user end) to avoid overheating the media. • Recovery from carriage motion errors while in Sleep Mode — the printer is now able to recover from carriage motion errors, such as when the cover is raised, that occur during Sleep Mode. • Printhead service during Sleep Mode — the printer now remembers if the printer was in Sleep Mode before an automatic printhead service.
Version 2.0 • Printhead servicing (purge and wipe) • Auto calibrations • Cooling the photodiode • Print mode used with internal print jobs — since the user print mode is unchanged, the print mode used for internal jobs is no longer reported on the control panel.
Version 1.11 • Aperture settings included — the UV Lamps Apertures settings, omitted from the Media Wizard settings screen in previous versions of the software, now appear on this screen. • Service station vacuum switched off after head motion failure — after a head montion failure, the service station vacuum now shuts off immediately, rather than waiting for the user to press a key on the control panel.
Version 1.10 • Printer stuck at “Finishing Job” — to prevent the printer from remaining in the “Finishing Job” state after a job has printed, the control panel will display a Cancel button if an end-of-job indication is not received from the RIP after one minute. If no such indication is received for ten minutes, or if the VideoNet cable connection is lost during this time, the printer will close the connection and go back to the ready state.
Version 1.08 sheets using the Minimal method; or Full Measure on all loads, which always uses the method selected in Measure Media Type. Full Measure only on first load can increase the thoughput speed of multiple-copy print jobs when the media dimensions are known to be uniform. It is not recommended for jobs that require very precise placement of images relative to the edges of the media.
Version 1.07 • NEW Sharp Edge — Sharp Edge reduces overspray at the edges of images and blocks of color. It is available for all resolutions in Production mode, and 1200x600 and 600x600 dpi in High Quality mode. Fine Text and Sharp Edge usage are reported in the gutter on printed output (when the gutter is enabled). You can enable or disable Sharp Edge mode via the Print Mode button on the Front Page screen.
Version 1.06 • Print head warming errors — various improvements have been made to ensure that the printheads are warmed to the correct temperature for printing. • Media settings adjustments while printing is paused — media settings can now be adjusted while printing is paused. • Unidirectional print modes — the left-only and right-only print modes now print in the correct directions. Version 1.
Version 1.04 • NEW Job Tracking Log — you can view a list of the last ten print jobs by pressing the printer status area of the Front Page screen (near the center top edge of the screen), then pressing the View Job Tracking Log key. If the job failed to print, an error code is listed, which can be reported to Technical Services for diagnosis. Version 1.
Version 1.
© Copyright 2008, 2009 Hewlett-Packard Development Company, L.P. Confidential computer software. Valid license from HP required for possession, use or copying. Consistent with FAR 12.211 and 12.212, Commercial Computer Software, Computer Software Documentation, and Technical Data for Commercial Items are licensed to the U.S. Government under vendor's standard commercial license. The information contained herein is subject to change without notice.
