HP Designjet T1100 MFP Printer - Assembly Instructions

ManualsBrandsHP ManualsPrinterHP Designjet T1100 MFP series

Read these instructions carefully...

What you will need for this procedure

• Because the scanner is heavy, you may

need three people to unpack it. When

more than one person is needed, the symbol

at the foot of this box is displayed.

• During the stand assembly you will see

some reference to the following symbol

labels which appear on some items, stand-

ing for left side, and right side.

L Left side

R Right side

The touch screen assembly can be mounted

on either the right or the left side of the

stand.

Touch screen assembly

HP Designjet

T11XX (HD) MFP

Assembly Instructions

Inkjet Commercial Division

Avenida Graells 501 · 08174

Sant Cugat del Vallès

Barcelona · Spain

Your printer should already be assembled

and working before starting this procedure.

For instructions on how to assemble the

printer, please refer to the assembly poster

included with the printer.

Assembly poster

HP DesignJet Information EngineeringHP DesignJet Information Engineering

Printed in Germany Imprimé en Allemagne Stampato in Germania

Summary of content (10 pages)

PAGE 1
HP Designjet T11XX (HD) MFP Assembly Instructions Read these instructions carefully... What you will need for this procedure • Because the scanner is heavy, you may need three people to unpack it. When more than one person is needed, the symbol at the foot of this box is displayed. • During the stand assembly you will see some reference to the following symbol labels which appear on some items, standing for left side, and right side.
PAGE 2
Stand assembly Unpacking stand 1 Attach the lower bar to the two legs. Tighten the screws with the T-handle torx driver T30 found in the assembly kit. M6×10 2 7 Turn the legs upside down, and attach the two feet to the left and right legs. legs using four M6×30 screws (two for each foot). Tighten the screws with the T-handle Torx driver T30 found in the assembly kit. M6×30 HP DesignJet Information Engineering 3 M6×10 Attach the bottom bar to the legs.
PAGE 3
Using the three legs upside people;down, two toand lift,attach and one the to 10 7 Turn two position, feet to the lift the left scanner and rightinto legs place using locating four M6×30 the rubber screws feet(two in the for holes each indicated. foot). Tighten the screws with the T-handle Torx driver T30 found in the assembly kit. 7 11 Connect the rear table. This is fitted by locating the four guide pins on the rear of the table into the rubber-framed holes on the top bar.
PAGE 4
13 Attach two (M6X10) screws to the leg, and two (M5X14) screws with two starwashers; one on the leg and one on the top bar triangular brace piece where shown. Don’t tighten them fully; leave a 4mm gap. 14 Slide the touch screen bracket into place over the four screws. 15 Tighten the four screws.
PAGE 5
Push the keyboard table down until the pointer slots into place on the touch screen arm. touch screen pen to the side of the 22 Fixtouchthescreen. 24 Remove the foam retainer from inside the scanner. 25 Close the scanner corner cover. The unit is now assembled and should appear as in the below illustration. 26 Slide the assembled printer under the scanner. The printer’s feet will be positioned outside the scanner’s feet. Cabling and connecting 21 23 Open the scanner corner cover.
PAGE 6
the cable bundle to the touch 28 Connect screen as shown (passing it between the bracket and the scanner); inserting the Power, USB, FireWire, and Network connections. the cover on the side of the scan29 Remove ner, and insert one of the FireWire cables the protected part of the bundle cable 30 Fitcoming from the screen into four large the ‘Y’ power cable into the clips. Then 33 Fitattach the clips to the stand.
PAGE 7
the glass with a lint-free cloth and 38 Clean a mild, streak-free, glass cleaner. HP DesignJet Information Engineering have not done so already, connect 36 Iftheyouprinter to a power outlet and switch it on. the glass fully using a separate clean, 39 Dry dry lint-free cloth like the one provided with the maintenance kit. Cleaning the scan area the ‘Y’ power cable to a power 35 Connect outlet. You are now required to clean the scan area.
PAGE 8
Dry the white background plate, rollers, and surrounding area fully using a separate clean, dry lint-free cloth. initialise: choose your language 46 To(below), read the license agreement, press I Agree, and hide the getting started window. HP DesignJet Information Engineering the scanner cover and push down 43 Close on the top to lock it into place. Note: if when switching on the touch screen a No scanner was found message appears, please press the Rescan option on the touch screen.
PAGE 9
follow the instructions that appear 48 Now on the touch screen. The maintenance wizard will ask you to insert the maintenance sheet. The sheet’s printed side must be face down. Feed the paper in aligning the two midpoint arrows. Press Next to continue. Note: if already installed, make sure you remove the magnetic media guides for this part of the process. Connecting to the printer 47 To start the maintenance procedure: 1: On the touch screen, press the setup tab.
PAGE 10
Your HP Designjet comes equipped with two magnetic media guides; these can be placed and moved as required. The scanner’s ruler can be changed between centimeters and inches by sliding it out, turning it over, and reinserting it. For any further information on how to use your scanner, see the online help system available from your touch screen using the button below.