HP StorageWorks Enterprise Modular Library E-Series Interface Manager card CompactFlash replacement instructions (AD560-96042, August 2008)

ManualsBrandsHP ManualsStorageHP EML Base Library

HP StorageWorks EML E-Series

Interface Manag

er card

CompactFlash replacement

instructions

You can use this 1 GB CompactFlash only on the

34025 2-003 Interface Manager card. This version of

the Interface Manager card contains a label with the

part number “AS#340252-003”, has a USB por t next

to the serial port, and has the word “D UAL” printed

on the bezel. You cannot use this CompactFlash on

the 340252-001 or 340252-002 Interface Manager

cards.

Second edition: August 2008

The information in this document is subject to change without

notice.

Printed in the US

www.hp.com

560-96042

CAUTION:

Parts can be damaged by electrostatic discharge. Keep parts in

theircontainersuntilneeded.Makesurethatyouareproperly

grounded when touching static-sensitive components.

CAUTION:

This part is NOT hot-pluggable. You must power off the library to

replace this part.

CAUTION:

This procedur

ecausesallInterfaceManagercardconﬁguration

settings to be lost. You must reconﬁgure the Interface Manager

card after re

placing the CompactFlash card.

Determine the IP address conﬁguration

If possible, determine whether the Interface Manager card’s IP address

is static or dynamic. You might be able to determine this from th e

Operator Control Panel (OCP), the Interface Manager user interface,

or other records.

• If the IP address is dynamic, go to the next step.

• If the IP address is static, write down the IP address, default gateway,

and subnet mask. You will need this information to reconﬁgure the

Interface Manager card.

Open the

library doors

10538

Open the back doors of the library.

Power off the library

Use yo

ur backup software or the Operator Control Panel (OCP ) to

empty

the picker or to verify that the picker is empty. Set the library

powe

r switch at the upper right corner to the OFF position. Make sure

that all power indicators on the power supplies are off.

Page 1

Summary of content (4 pages)

PAGE 1
HP StorageWorks EML E-Series Interface Manager card CompactFlash replacement instructions CAUTION: Parts can be damaged by electrostatic discharge. Keep parts in their containers until needed. Make sure that you are properly grounded when touching static-sensitive components. CAUTION: This part is NOT hot-pluggable. You must power off the library to replace this part. CAUTION: This procedure causes all Interface Manager card configuration settings to be lost.
PAGE 2
Identify the Interface Manager card Remove the original CompactFlash card 10032a Grasp the edges of the CompactFlash card and slide it out of the flash memory slot. If needed, push a pen into the corner notches of the CompactFlash slot to unseat it. Insert the new CompactFlash card 10539 The Interface Manager card is located in the bottom slot of the base module card cage.
PAGE 3
To update the firmware with the CLI: 1. Using a PC or laptop connected to the LAN, download the latest firmware from the web site: http://www.hp.com/support/cvtl Reconnect the cables nl 2. Use FTP to transfer the firmware file to a temporary storage area in the Interface Manager card’s memory. a. To determine the IP address to use, look at the OCP on the front of the library. From the Home screen, select the Status tab, and then select Identity Screen. b.
PAGE 4
3. The IP address of the library might have changed after replacing the CompactFlash. To avoid having the library appear more than once in the Command View TL Launcher window, remove the original instance of the library, and then add it again. configuration steps” section of the HP StorageWorks Interface Manager and Command View TL user guide for instructions on how to reconfigure the Interface Manager card. a. In the Launcher window, click the Library Selection tab. b.