7 GETTING STARTED
HP ENVY17 3D Getting Started
© Copyright 2010 Hewlett-Packard Development Company, L.P. ATI Catalyst is a trademark of Advanced Micro Devices, Inc. Microsoft and Windows are U.S. registered trademarks of Microsoft Corporation. Bluetooth is a trademark owned by its proprietor and used by Hewlett-Packard Company under license. SD Logo is a trademark of its proprietor. The information contained herein is subject to change without notice.
User Guides HP is committed to reducing the environmental impact of our products. As part of this effort, we provide user guides and learning centers on your computer hard drive in Help and Support. Additional support and updates to the user guides are available on the Web.
Safety warning notice WARNING! To reduce the possibility of heat-related injuries or of overheating the computer, do not place the computer directly on your lap or obstruct the computer air vents. Use the computer only on a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow.
vi Safety warning notice
Table of contents 1 Welcome .......................................................................................................................................................... 1 What's new ........................................................................................................................................... 2 HP 3D Cinema Technology ................................................................................................. 2 Beats Audio .....................................
Can I play stereoscopic 3D games on my computer ......................................................... 22 Can I wear the 3D glasses to a 3D movie in a movie theater ............................................ 22 Can I wear my 3D glasses over my prescription glasses .................................................. 22 How do I clean my 3D glasses .......................................................................................... 22 How close do I need to be to the computer to view 3D content ....
Pinching/Zooming ............................................................................. 45 6 Maintenance .................................................................................................................................................. 46 Removing or inserting the battery ...................................................................................................... 46 Removing the battery .........................................................................................
x
1 Welcome The following sections are included in this chapter: ● What's new ● Finding information After you set up and register the computer, it is important to take the following steps: ● Connect to the Internet—Set up your wired or wireless network so that you can connect to the Internet. For more information, refer to Networking on page 33. ● Update your antivirus software—Protect your computer from damage caused by viruses.
What's new HP 3D Cinema Technology HP 3D Cinema Technology provides exceptional, cinema-quality stereoscopic 3D entertainment. The computer’s integrated 3D features, along with the HP 3D Active Shutter Glasses, provide an outstanding 3D visual experience. For more information, refer to Using HP 3D Cinema Technology on page 7. NOTE: Before using 3D Cinema Technology and the 3D glasses, read the 3D safety information. Consult a physician if you suspect a physical problem seeing stereoscopic 3D.
Beats Audio Beats Audio is an enhanced audio profile that provides a deep, controlled bass while maintaining a clear sound. Beats Audio is enabled by default. ▲ To increase or decrease the Beats Audio bass settings, press fn+b. NOTE: You can also view and control the bass settings through the Windows operating system. Select Start > Control Panel > Hardware and Sound > HP Beats Audio Control Panel > Equalization to view and control the bass properties.
Example display configuration for single large surface (SLS) When you use 3 external displays and span the image across them as an SLS, the computer display is turned off. The 3 external displays are connected to the computer using the external monitor port (VGA), the Mini DisplayPort, and the HDMI port. NOTE: Identical resolution is required among all displays to form the SLS mode. Displays with different native resolutions can still form an SLS mode by using non-native resolutions.
Resources For information about Quick Setup poster ● How to set up the computer ● Help to identify computer components HP Notebook Reference Guide ● Power management features To access this guide, select Start > Help and Support > User Guides.
Resources For information about Limited Warranty* Warranty information To access this warranty: Select Start > Help and Support > Warranty. – or – Go to http://www.hp.com/go/orderdocuments. *You may find the expressly provided HP Limited Warranty applicable to your product located with the electronic guides on your computer and/or on the CD/DVD provided in the box. Some countries/regions may provide a printed HP Limited Warranty in the box.
2 Using HP 3D Cinema Technology The following sections are included in this chapter: ● 3D safety information ● What is stereoscopic vision and 3D ● What is HP 3D Cinema Technology ● Using the HP 3D Active Shutter Glasses ● Using 3D Cinema Technology ● Understanding 3D formats ● Using HP MediaSmart ● Caring for the 3D glasses ● Troubleshooting and frequently asked questions 3D safety information Carefully read all of the following safety precautions before using the 3D glasses and 3D Cine
WARNING! If you cannot see 3D content after you set up 3D Cinema Technology, HP recommends that you discontinue use. Consult a physician if you suspect a physical problem seeing stereoscopic 3D. Photosensitive Epileptic Seizures—Some individuals may experience a seizure or other complications when exposed to certain visual images, including flashing lights or patterns that may appear in 3D content.
What is stereoscopic vision and 3D When you see the world through both eyes, you are actually looking at two pictures merged into one. Your right eye and your left eye each deliver a separate image to your brain, which meshes these two images into one three-dimensional picture. Most movies in the past were only able to provide one image on the screen, and 3D effects had to be simulated by other means.
Using the HP 3D Active Shutter Glasses Your 3D experience begins with active 3D content and the 3D glasses. The 3D glasses are battery powered and linked wirelessly to the infrared (IR) emitters in your 3D computer. WARNING! Before using the 3D glasses, read the 3D safety information. NOTE: For optimal 3D viewing, you should be no more than approximately 1.5 meters (5 feet) from the computer display. Depending on the viewing angle, the operational distance from the display can vary.
● Once the 3D content begins to play, the lenses may appear to darken and you may see some flickering as the glasses begin to turn on. ● The battery installed in the glasses provides approximately 180 hours of 3D viewing time. To help conserve battery power, the glasses enter Standby if no IR signal is detected for 5 seconds.
Using 3D Cinema Technology After you set up your 3D computer, you are ready to verify that you can properly view the 3D content. NOTE: Be sure that your computer is connected to AC power when viewing 3D content. NOTE: For optimal 3D viewing, the screen brightness controls are disabled when watching 3D content. 1.
Understanding 3D formats Your computer supports the following 3D formats: ● Blu-ray 3D movies ● 3D MPEG 4 MVC files NOTE: To play back 3D MPEG 4 MVC files, you need to place them in the following location: C:\user\public\Public Videos\HP 3D demo videos NOTE: 3D playback is only supported in full-screen mode.
Using HP MediaSmart When you open MediaSmart, the control panel displays the following items. NOTE: Some controls may not be shown when the window is minimized. Components Description (1) Settings control Click to select DVD and BD preferences and adjust the settings. (2) Playback controls To display the controls, move the computer mouse pointer. NOTE: The appearance and operation of the controls depends on the type of DVD or BD being viewed.
NOTE: Available DVD settings depend on the type of DVD or BD being viewed. ● Screen refresh rate—Adjust the screen refresh rate to either 96 Hz or 120 Hz. ● 3D Image Adjustment—Switch the left eye frame and the right eye frame if the 3D output appears incorrect. ● 2D/3D movie playback—Select to either continue or restart movie playback when switching between 2D and 3D modes.
Adjusting the refresh rate For the best experience when watching 3D content, you may need to manually adjust the refresh rate. 1. Click the Settings icon on the bottom of the MediaSmart control panel. The Settings window opens. 2. Click the Advanced tab. 3. In the Screen Refresh Rate drop-down menu, select a different screen refresh rate. 4. Click Apply.
Settings for 2D and 3D modes 3D discs have either 3D-only content or both 2D and 3D content. Depending on the type of 3D disc you are watching, you may need to adjust the MediaSmart DVD settings to see all of the menus available on your disc. The following settings are available: ● Continue movie playback when switching between 2D and 3D modes (factory default)— This setting provides uninterrupted movie playback when switching between 2D and 3D modes. This setting only supports 3D BD-J interactive content.
Caring for the 3D glasses Using the nose pieces The 3D glasses come with 3 nose pieces in different sizes. One nose piece is installed at the factory and two additional nose pieces ship with the glasses. Try on the glasses, and change the nose piece if needed to find a comfortable fit. You can also wear the glasses without a nose piece if needed. NOTE: ▲ 18 The 3D glasses are designed to fit over most standard prescription glasses. To add a nose piece, insert the nose piece onto the glasses.
Replacing the battery The battery in the 3D glasses ships preinstalled in the battery compartment and provides approximately 180 hours of 3D viewing time. HP recommends that the battery be replaced once a year. The glasses can stay in Standby mode for up to one year. The 3D glasses use a basic CR2032 type battery. These batteries can easily be replaced and can be purchased anywhere batteries are sold. To replace the battery: 1.
Cleaning the 3D glasses To remove smudges and lint, frequently clean the 3D glasses with a soft, damp, lint-free cloth. The cloth can be dampened with mild cleaning agents with less than 10% alcohol. CAUTION: To prevent permanent damage to the 3D glasses: Do not use paper-based towels, because they can scratch the lenses. Do not spray cleaning fluids or chemicals directly on the lenses. Do not use ammonia-based cleaning products.
Troubleshooting and frequently asked questions I cannot see 3D content If you are watching in 3D mode and cannot see 3D content, HP recommends that you not use the 3D glasses. Refer to the information below and 3D safety information on page 7. Consult a physician if you suspect a physical problem seeing stereoscopic 3D. ● You may be trying to watch 3D content in 2D mode. ● The battery in the 3D glasses may need to be replaced. Refer to Replacing the battery on page 19 for additional information.
What 3D formats are supported on my computer The following 3D formats are supported on your computer: ● Blu-ray 3D movies ● 3D MPEG 4 MVC files Refer to Using HP MediaSmart on page 14 for additional information. Can I play stereoscopic 3D games on my computer You may need to purchase additional software to view stereoscopic 3D games. Contact the gaming software manufacturer for more information.
3 Getting to know your computer The following sections are included in this chapter: ● Top ● Front ● Right-side ● Left-side ● Display ● Bottom Top TouchPad Component (1) Description TouchPad light Turns the TouchPad on and off. Quickly double-tap the TouchPad light to turn the TouchPad on and off.
Component Description (2) Left TouchPad button Functions like the left button on an external mouse. (3) Right TouchPad button Functions like the right button on an external mouse. (4) TouchPad zone Moves the pointer and selects or activates items on the screen. Lights Component (1) (2) (3) (4) (5) Description TouchPad light Caps lock light Power light Mute light Wireless light ● Amber: The TouchPad is off. ● Off: The TouchPad is on. ● White: Caps lock is on.
Button Component Description Power button ● When the computer is off, press the button to turn on the computer. ● When the computer is on, press the button briefly to initiate Sleep. ● When the computer is in the Sleep state, press the button briefly to exit Sleep. ● When the computer is in Hibernation, press the button briefly to exit Hibernation.
Keys Component 26 Description (1) esc key Displays system information when pressed in combination with the fn key. (2) fn key Executes frequently used system functions when pressed in combination with the b key or the esc key. (3) Windows logo key Displays the Windows Start menu. (4) Action keys Execute frequently used system functions. (5) Windows applications key Displays a shortcut menu for items beneath the pointer.
Front Component (1) (2) Description Power light Drive light ● White: The computer is on. ● Blinking white: The computer is in the Sleep state. ● Off: The computer is off or in Hibernation. ● Blinking white: The hard drive is being accessed. ● Amber: HP ProtectSmart Hard Drive Protection has temporarily parked the hard drive. NOTE: For information on HP ProtectSmart Hard Drive Protection, refer to the HP Notebook Reference Guide. (3) Speakers (2) Produce sound.
Right-side Component Description (1) USB ports (2) Connect optional USB devices. (2) Digital Media Slot Supports the following digital card formats: (3) Optical drive ● Memory Stick ● Memory Stick Pro ● MultiMediaCard ● Secure Digital (SD) Memory Card ● Secure Digital High Capacity Memory Card ● xD-Picture Card Reads and writes to an optical disc. CAUTION: Do not insert 8-cm optical discs into the optical drive. This can cause damage to the computer.
Left-side Component (1) Description Vent Enables airflow to cool internal components. NOTE: The computer fan starts up automatically to cool internal components and prevent overheating. It is normal for the internal fan to cycle on and off during routine operation. (2) External monitor port Connects an external VGA monitor or projector. (3) RJ-45 (network) jack Connects a network cable.
Component (8) Description Audio-out (headphone) jack/Audio-in (microphone) jack Produces sound when connected to optional powered stereo speakers, headphones, earbuds, a headset, or television audio. Also connects an optional headset microphone. WARNING! To reduce the risk of personal injury, adjust the volume before putting on headphones, earbuds, or a headset. For additional safety information, refer to the Regulatory, Safety, and Environmental Notices.
Display Component Description (1) WLAN antennas (2)* Send and receive wireless signals to communicate with wireless local area networks (WLAN). (2) IR emitters* Wirelessly synchronize the 3D glasses with the computer display. (3) Internal microphones (2) Record sound. (4) Webcam light On: The webcam is in use. (5) Webcam Records video and captures still photographs. To access the webcam, select Start > All Programs > HP > HP MediaSmart > HP MediaSmart Webcam.
Bottom Component Description (1) Subwoofer Contains the subwoofer speaker. (2) Battery bay Holds the battery. NOTE: The battery is preinstalled in the battery bay at the factory. (3) Vents (7) Enable airflow to cool internal components. NOTE: The computer fan starts up automatically to cool internal components and prevent overheating. It is normal for the internal fan to cycle on and off during routine operation. 32 (4) Hard drive bay Holds the hard drive.
4 Networking The following sections are included in this chapter: ● Using an Internet service provider (ISP) ● Connecting to a wireless network NOTE: Internet hardware and software features vary depending on computer model and your location. Your computer supports two types of Internet access: ● Wireless—For mobile Internet access, you can use a wireless connection. Refer to Connecting to an existing WLAN on page 34 or Setting up a new WLAN network on page 36.
Using an Internet service provider (ISP) Before you can connect to the Internet, you must establish an ISP account. Contact a local ISP to purchase Internet service and a modem. The ISP will help set up the modem, install a network cable to connect your wireless computer to the modem, and test the Internet service. NOTE: Your ISP will give you a user ID and password to access the Internet. Record this information and store it in a safe place.
3. Click the network icon in the notification area, at the far right of the taskbar. 4. Select a network to connect to. 5. Click Connect. 6. If required, enter the security key.
Setting up a new WLAN network Required equipment: ● A broadband modem (either DSL or cable) (1) and high-speed Internet service purchased from an Internet service provider (ISP) ● A wireless router (purchased separately) (2) ● Your new wireless computer (3) NOTE: Some modems have a built-in wireless router. Check with your ISP to determine what type of modem you have. The illustration shows an example of a completed WLAN network installation that is connected to the Internet.
Configuring a wireless router For help in setting up a WLAN, refer to the information provided by your router manufacturer or your ISP. The Windows operating system also provides tools to help you set up a new wireless network. To use the Windows tools to set up your network, select Start > Control Panel > Network and Internet > Network and Sharing Center > Set up a new connection or network > Set up a new network. Then follow the on-screen instructions.
5 Keyboard and pointing devices The following sections are included in this chapter: ● Using the keyboard ● Using pointing devices Using the keyboard Using the action keys Action keys are customized actions that are assigned to specific keys at the top of the keyboard. To use an action key, press and hold this key to activate the assigned action. NOTE: Depending on the program you are using, pressing fn and one of the action keys will open a specific shortcut menu within that application.
Icon Action Description Switch screen image Switches the screen image among display devices connected to the system. For example, if a monitor is connected to the computer, this key alternates the screen image from computer display to monitor display to simultaneous display on both the computer and the monitor. Most external monitors receive video information from the computer using the external VGA video standard.
Using the hotkeys A hotkey is a combination of the fn key (1) and either the esc key (2) or the b key (3). To use a hotkey: ▲ Briefly press the fn key, and then briefly press the second key of the hotkey combination. Function Hotkey Description Display system information. fn+esc Displays information about system hardware components and the system BIOS version number. Control the bass settings. fn+b Increases or decreases the Beats Audio bass settings.
Using the keypad Using the integrated numeric keypad Component Description Integrated numeric keypad Can be used like an external numeric keypad. NOTE: The computer does not have a num lock key.
Using pointing devices NOTE: In addition to the pointing devices included with your computer, you can use an external USB mouse (purchased separately) by connecting it to one of the USB ports on the computer. Setting pointing device preferences Use Mouse Properties in Windows® to customize settings for pointing devices, such as button configuration, click speed, and pointer options. To access Mouse Properties, select Start > Devices and Printers.
Turning the TouchPad off and on To turn the TouchPad off and on, quickly double-tap the TouchPad light. NOTE: If the TouchPad light is amber, the TouchPad is off. Navigating To move the pointer, slide one finger across the TouchPad in the direction you want the pointer to go.
Selecting Use the left and right TouchPad buttons like the corresponding buttons on an external mouse. Using TouchPad gestures The TouchPad supports a variety of gestures. To use TouchPad gestures, place two fingers on the TouchPad at the same time. To turn the gestures on and off: 1. Double-click the Synaptics icon in the notification area, at the far right of the taskbar, and then click the Device Settings tab. 2. Select the device, and then click Settings. 3.
Scrolling Scrolling is useful for moving up, down, or sideways on a page or image. To scroll, place two fingers slightly apart on the TouchPad and drag them across the TouchPad in an up, down, left, or right motion. NOTE: Scrolling speed is controlled by finger speed. Pinching/Zooming Pinching allows you to zoom in or out on images or text. ● Zoom in by placing two fingers together on the TouchPad, and then moving them apart.
6 Maintenance The following sections are included in this chapter: ● Removing or inserting the battery ● Replacing or upgrading the hard drive ● Adding or replacing memory modules ● Routine care ● Updating programs and drivers Removing or inserting the battery NOTE: The battery is preinstalled in the battery bay at the factory. NOTE: For additional information on using the battery, refer to the HP Notebook Reference Guide.
Inserting the battery ▲ Align the tabs on the battery with the notches on the outer edge of the battery bay (1), and rotate the battery into the battery bay until it is seated (2). The battery release latch (3) automatically locks the battery into place.
Replacing or upgrading the hard drive CAUTION: To prevent information loss or an unresponsive system: Shut down the computer before removing the hard drive from the hard drive bay. Do not remove the hard drive while the computer is on, in the Sleep state, or in Hibernation. If you are not sure whether the computer is off or in Hibernation, turn the computer on by pressing the power button. Then shut down the computer through the operating system. NOTE: Select computer models can support up to two drives.
6. Disconnect the hard drive cable (1) from the computer, and then lift the hard drive (2) out of the hard drive bay. 7. Disconnect the hard drive cable from the hard drive.
Installing a hard drive 50 1. Connect the hard drive cable to the hard drive. 2. Insert the hard drive (1) into the hard drive bay, and then connect the hard drive cable (2) to the computer. 3. Align the tabs (1) on the hard drive cover with the notches on the computer. 4. Close the cover (2).
5. Tighten the hard drive cover screws (3). 6. Replace the battery. 7. Reconnect external power and external devices. 8. Turn on the computer. Adding or replacing memory modules The computer has two memory module slots. The memory module slots are located on the bottom of the computer under the hard drive cover. The memory capacity of the computer can be upgraded by adding a memory module or replacing the existing memory module in one of the memory module slots.
CAUTION: To prevent information loss or an unresponsive system: Shut down the computer before removing a memory module from the computer. Do not remove a memory module while the computer is on, in the Sleep state, or in Hibernation. If you are not sure whether the computer is off or in Hibernation, turn the computer on by pressing the power button. Then shut down the computer through the operating system. 1. Save your work and shut down the computer. 2.
b. 6. Remove the memory module compartment cover (2). If you are replacing a memory module, remove the existing memory module: a. Pull away the retention clips (1) on each side of the memory module. The memory module tilts up. b. Grasp the edge of the memory module (2), and then gently pull the module out of the memory module slot. CAUTION: To prevent damage to the memory module, hold the memory module by the edges only. Do not touch the components on the memory module.
CAUTION: To prevent damage to the memory module, hold the memory module by the edges only. Do not touch the components on the memory module, and do not bend the memory module. 8. 54 a. Align the notched edge (1) of the memory module with the tab in the memory module slot. b. With the memory module at a 45-degree angle from the surface of the memory module compartment, press the module (2) into the memory module slot until it is seated. c.
c. 9. Tighten the 2 memory module compartment cover screws (3). Replace the hard drive cover. a. Align the tabs (1) on the hard drive cover with the notches on the computer. b. Close the cover (2). c. Tighten the 2 hard drive cover screws (3). 10. Replace the battery. 11. Reconnect external power and external devices. 12. Turn on the computer.
Routine care Cleaning the display CAUTION: To prevent permanent damage to the computer, never spray water, cleaning fluids, or chemicals on the display. To remove smudges and lint, frequently clean the display with a soft damp, lint-free cloth. If the screen requires additional cleaning, use premoistened antistatic wipes or an antistatic screen cleaner. Cleaning the TouchPad and keyboard Dirt and grease on the TouchPad can cause the pointer to jump around on the screen.
Updating programs and drivers HP recommends that you update your programs and drivers on a regular basis. Go to http://www.hp.com/support to download the latest versions. You can also register to receive automatic update notifications when they become available.
7 Backup and recovery The following sections are included in this chapter: ● Recovery discs ● Performing a system recovery ● Backing up your information Recovery after a system failure is as good as your most recent backup. HP recommends that you create recovery discs immediately after software setup. As you add new software and data files, you should continue to back up your system on a regular basis to maintain a reasonably current backup.
Guidelines: ● Purchase high-quality DVD-R, DVD+R, BD-R (writable Blu-ray), or CD-R discs. DVDs and BDs have a much higher storage capacity than CDs. If you use CDs, up to 20 discs may be required, whereas only a few DVDs or BDs are required. NOTE: Read-write discs, such as CD-RW, DVD±RW, double-layer DVD±RW, and BD-RE (rewritable Blu-ray) discs, are not compatible with the Recovery Manager software. ● The computer must be connected to AC power during this process.
To restore the computer from the partition, follow these steps: 1. Access Recovery Manager in either of the following ways: ● Select Start > All Programs > Recovery Manager > Recovery Manager. – or – ● Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen. Then, press f11 while the “F11 (HP Recovery)” message is displayed on the screen. 2. Click System Recovery in the Recovery Manager window. 3.
Using Windows Backup and Restore Windows Backup and Restore allows you to back up individual files or back up the entire computer image. Guidelines: ● Be sure that the computer is connected to AC power before you start the backup process. ● Allow enough time to complete the backup process. Depending on file sizes, it may take over an hour. To create a backup: 1. Select Start > Control Panel > System and Security > Backup and Restore. 2.
Restore to a previous date and time To revert to a restore point (created at a previous date and time), when the computer was functioning optimally, follow these steps: 62 1. Select Start > Control Panel > System and Security > System. 2. In the left pane, click System Protection. 3. Click the System Protection tab. 4. Click System Restore. 5. Follow the on-screen instructions.
8 Customer support The following sections are included in this chapter: ● Contacting Customer Support ● Labels Contacting Customer Support If the information provided in this Getting Started guide, in the HP Notebook Reference Guide, or in Help and Support does not address your questions, you can contact HP Customer Support at: http://www.hp.com/go/contactHP NOTE: For worldwide support, click Contact HP worldwide on the left side of the page, or go to http://welcome.hp.com/country/us/en/wwcontact_us.
Component (1) Product name (2) Serial number (s/n) (3) Part number/Product number (p/n) (4) Warranty period (5) Model description Have this information available when you contact technical support. The serial number label is affixed to the bottom of the computer. 64 ● Microsoft® Certificate of Authenticity—Contains the Windows Product Key. You may need the Product Key to update or troubleshoot the operating system.
9 Specifications The following sections are included in this chapter: ● Input power ● Operating environment Input power The power information in this section may be helpful if you plan to travel internationally with the computer. The computer operates on DC power, which can be supplied by an AC or a DC power source. The AC power source must be rated at 100–240 V, 50–60 Hz.
Operating environment Factor Metric U.S.
Index Symbols/Numerics 3D Active Shutter Glasses battery compartment 10 caring 18 cleaning 20 handling 20 identifying 10 nose pieces 10, 18 replacing the battery 19 turning on and off 10 using 10 3D Cinema Technology 3D games 22 adjusting settings 14 effective range 22 flickering 22 frequently asked questions 21 left eye/right eye switching 16 refresh rate 12 safety information 7 switching between 2D and 3D 16 using 12 watching content 13 3D settings, adjusting 14 A action keys adjusting volume 39 Help and
internal microphones, identifying 31 Internet connection setup 33 IR emitters, identifying 31 ISP, using 34 J jacks audio-in (microphone) 30 audio-out (headphone) 30 RJ-45 (network) 29 K keyboard backlight action key 39 keyboard hotkeys, identifying 40 keypad, integrated 26, 41 keys action 26 esc 26 fn 26 optical drive eject 26 Windows applications 26 Windows logo 26 L labels Bluetooth 64 Microsoft Certificate of Authenticity 64 regulatory 64 serial number 63 wireless certification 64 WLAN 64 latch, battery
T TouchPad buttons 24 navigating 43 selecting 44 turning on and off 43 using 42 TouchPad gestures pinching 45 scrolling 45 using 44 zooming 45 TouchPad light 23, 24 TouchPad zone, identifying 24 traveling with the computer 64 troubleshooting 3D 21 3D games 22 cannot see 3D content 21 flickering 22 supported 3D formats 22 U USB ports, identifying Z zooming TouchPad gesture 45 28 V vents, identifying 29, 32 volume keys, identifying 39 W webcam light, identifying 31 webcam, identifying 31 Windows applicati
