Manualshelf

HP StorageWorks ESL E-Series e2400-FC 2Gb Interface Controller Upgrade (AA928-96014, October 2007)

ManualsBrandsHP ManualsStorageHP ESL 712e Ultrium Tape Library
123456
ACT/
LNK
ACT/
LNK
PORT 1 PORT 0 ETHERNET
SERIAL
PWR
FIBRE
CHANNEL
FIBRE
CHANNEL
ACT/
LNK
ACT/
LNK
PORT 1 PORT 0 ETHERNET
SERIAL
PWR
FIBRE
CHANNEL
FIBRE
CHANNEL
ACT/
LNK
ACT/
LNK
PORT 1 PORT 0 ETHERNET
SERIAL
PWR
FIBRE
CHANNEL
FIBRE
CHANNEL
ACT/
LNK
ACT/
LNK
PORT 1 PORT 0 ETHERNET
SERIAL
PWR
FIBRE
CHANNEL
FIBRE
CHANNEL
ACT/
LNK
ACT/
LNK
PORT 1 PORT 0 ETHERNET
SERIAL
PWR
FIBRE
CHANNEL
FIBRE
CHANNEL
ACT/
LNK
ACT/
LNK
PORT 1 PORT 0 ETHERNET
SERIAL
PWR
FIBRE
CHANNEL
FIBRE
CHANNEL
ACT/
LNK
ACT/
LNK
PORT 1 PORT 0 ETHERNET
SERIAL
PWR
FIBRE
CHANNEL
FIBRE
CHANNEL
ACT/
LNK
PORT 2
FIBRE
CHANNEL
ACT/
LNK
ACT/
LNK
PORT 1 PORT 3
FIBRE
CHANNEL
FIBRE
CHANNEL
ACT/
LNK
PORT 2
FIBRE
CHANNEL
ACT/
LNK
ACT/
LNK
PORT 1 PORT 0 ETHERNET
SERIAL
PWR
FIBRE
CHANNEL
FIBRE
CHANNEL
ACT/
LNK
PORT 2
FIBRE
CHANNEL
ACT/
LNK
ACT/
LNK
PORT 1 PORT 0
FIBRE
CHANNEL
FIBRE
CHANNEL
ACT/
LNK
PORT 2
FIBRE
CHANNEL
ACT/
LNK
ACT/
LNK
PORT 1 PORT 0 ETHERNET
SERIAL
PWR
FIBRE
CHANNEL
FIBRE
CHANNEL
ACT/
LNK
PORT 2
FIBRE
CHANNEL
ACT/
LNK
ACT/
LNK
PORT 1 PORT 3
FIBRE
CHANNEL
FIBRE
CHANNEL
ACT/
LNK
PORT 2
FIBRE
CHANNEL
16
17 18
Connect the other end of the Ethernet cable to
the Ethernet port on the corresponding e2400-FC
2Gb interface controller.
Locate the small cable clamp on the upper right
corner of the first cluster frame. Using a #2
Phillips screwdriver, remove the screw from the
clamp. Place the Ethernet cable in the clamp,
then secure the clamp to the cluster frame by
replacing the screw.
Attach FC cables (not provided)
to the remaining interface controller FC ports. Route
them through access holes on the top or bottom of
the library cabinet and to a switch or an HBA.
Note: Use the labels provided to indicate
which drive cluster the FC cables are
interfacing with. Attach one label to each
end of the cables.
Ethernet Cable Connection
15
Connect the Ethernet cable to the
cluster controller card at port “E3.”
Note: You can use the labels provided
to indicate which drive cluster the FC
cables are interfacing with. Attach one
label to each end of the cables.
To help keep the FC cables clear of the drive
cluster below, attach the cables to the drive
handle on the lower right drive in the cluster
using the tie wrap provided.
14