FibrChanl-01 (fcd) Fibre Channel Mass Storage Driver for HP-UX 11i v3 Release Notes Version Number B.11.31.1105 HP Part Number: 5900-1776 Published: May 2011 Edition: 1.
Contents FibrChanl-01 (fcd) Fibre Channel Mass Storage Driver for HP-UX 11i v3 overview..............................3 New and changed features in this release...................................................................................3 New features......................................................................................................................3 Known problems fixed in this version...........................................................................................
This document provides information about the B.11.31.1105 release of the FibrChanl-01 (fcd) Fibre Channel Mass Storage Driver for HP-UX 11i v3. FibrChanl-01 (fcd) Fibre Channel Mass Storage Driver for HP-UX 11i v3 overview This release of the document for the FibrChanl-01 (fcd) Fibre Channel Mass Storage Driver for HP-UX 11i v3 (version B.11.31.1105) documents version changes and defect fixes. New and changed features in this release New features The following feature is new with the B.11.31.
Table 3 HP-UX September 2010 (AR1009) Fixes (continued) Defect ID Description QXCR1000815634 This fixes the issue where the fcmsutil utility returns the message Target port is in invalid state, when the user specifies the N_Port_ID as a parameter. QXCR1001030695 This fixes the issue where the fcd driver may panic with Bad News!, if the first open of the target failed because the link is down.
Table 7 HP-UX January 2010 (WEB1001) Fixes (continued) Defect ID Description QXCR1000922032 This fixes the issue where SNIA does not report more than 500 luns per HBA. QXCR1000976060 fcd panics during system dump to an EMC device. This issue, caused by sense data handling, has been fixed. QXCR1000966390 This fixes a system hang which occurred after CPU deletion. The hang was caused by interrupt migration handling in the fcd driver.
Known problems and limitations This section provides a list of known problems and limitations as known to HP at time of publication. If workarounds are available, they are included. • EFI boot fails when connected to an Arbitrated Loop device This applies to HP 8Gb and 4Gb 2 Port QLogic Mezzanine HBA s (part numbers 451871–B21 and 403619–B21).
• If a system is low on available contiguous memory, an online addition can fail The failure will be seen with messages similar to the following: #sd10vp3 :/> olrad -A 8-0-1-5 Activity : Start of Post Add Target slot : 8-0-1-5 Addition of the card in progress... [ NOTE: Killing or otherwise aborting this olrad command may not cancel the Card Add operation.
Corrective action: Install patch PHCO_36356 to fix this problem. This patch is delivered in the HWEnable11i patch bundle on the HP-UX 11i v3 (B.11.31) OEUR media for December 2007. You may also check availability of the patch at the HP IT Resource Center site: http:// itresourcecenter.hp.
• Using ioscan with krm Not Running When ioscan is run with the —fn or —Fn option, and the kernel resource monitor (krm) is not running, there could be stale krm device files in the system, which would correspond to different devices, including fcd, in ioscan output. This issue has no impact on the functionality of the Fibre Channel port; however, ioscan output may be confusing. This issue can impact any card accessible with ioscan, and is not specific to the cards supported by the fcd driver.
Table 13 Recommended firmware versions (May 2011) Fibre channel adapter EFI driver version Firmware version 451871-B21 2.20 or later 5.03.02 or later AH400A/AH401A 2.15 or later 4.04.04 or later AD193A/AD194A 2.15 or later 4.04.04 or later 403619-B21 2.15 or later 4.04.04 or later 403619-B21 (with VC-FC boot support in BL860c) 2.15 or later 4.04.04 or later AD300A 2.15 or later 4.04.04 or later AB378A 2.15 or later 4.04.04 or later AB378B 2.15 or later 4.04.04 or later AB379A 2.
Table 14 Table of Driver Versions (continued) Release Name Driver Version Release Date Application Release 1103 B.11.31.1103 March 2011 Web Release 1105 B.11.31.1105 May 2011 Hardware requirements This version of the FibrChanl-01 (fcd) Fibre Channel Mass Storage Driver for HP-UX 11i v3 runs on HP Integrity servers and HP PA servers with the HP-UX 11i v3 (11.31) operating system.
