FibrChanl-03 (fcoc) Fibre Channel Mass Storage Driver for HP-UX 11i v3 Release Notes Version Number B.11.31.1303 HP Part Number: 5900-3008 Published: March 2013 Edition: 1.
Contents FibrChanl-03 (fcoc) Fibre Channel Mass Storage Driver for HP-UX 11i v3 overview............................3 New and changed features in this release...................................................................................3 New features......................................................................................................................3 Known problems fixed in this version...........................................................................................
This document provides information about the B.11.31.1303 release of the FibrChanl-03 (fcoc) Fibre Channel Mass Storage Driver for HP-UX 11i v3. FibrChanl-03 (fcoc) Fibre Channel Mass Storage Driver for HP-UX 11i v3 overview This release of the document for the FibrChanl-03 (fcoc) Fibre Channel Mass Storage Driver for HP-UX 11i v3 (version B.11.31.1303) documents defect fixes and version changes. New and changed features in this release New features The following feature is new with the B.11.31.
Table 3 HP-UX March 2012 (AR1203) Fixes Defect ID Description QXCR1001144340 This fixes a timing-related hang issue in the FCOC driver that may occur when the driver is being unloaded. QXCR1001146915 This fixes fcocutil to print correct SFP information or print appropriate error message.
Table 5 HP-UX September 2011 (AR1109) Fixes (continued) Defect ID Description QXCR1001075202 This fixes the issue where ioscan may not show the fcoc driver’s device special files (DSFs) when a reboot is followed after FibrChanl-03 depot installation.
• Up to a total of eight NC551m and/or NC553m HBAs are supported in a BL890c i2 system. Up to a total of 140 Fibre Channel ports, which can be any combination of CN1100E and AT094A HBAs, are supported in a Superdome2 system. • The HP-UX boot path is lost during un-assign and re-assign of the BL8x0C i2 (Blade) profile. The scenario that leads to this is: 1. Create a profile and assign it to the blade. Install a SAN disk connected from HBA with HP-UX on it. 2. Power off the blade. 3.
2. 3. Select Emulex Configuration Utility Ver:X.XXXXX and press Enter. When the Emulex Configuration Utility screen is displayed with Emulex Configuration Setup Utility selected, press Enter. 4. A list of all the adapters in the system is displayed. Your list may vary depending on the installed adapters. Locate the adapter you want to configure. Use the up/down arrows on your keyboard to select it, and press Enter.
5. The Emulex Adapter Configuration Main Menu screen comes up. Select Set Boot From SAN. A Disable Enable menu is displayed. Use the arrow keys to select the Enable option and press Enter. The selection is updated to NVRAM and the current setting is displayed. 6. On the same Emulex Adapter Configuration Main Menu screen, select Back to Display Adapters and RECONNECT DEVICES and press Enter. Type s to save the changes. Exit the Emulex utility. Control B to go into cm and type rs to reset the system. 7.
• rx2800 i2 System Firmware s26.21 or higher • C7000 OA Firmware 3.20 or higher • VCSU FW 1.6.0 or higher • VC-Enet FW Version 3.15 or higher (for profile migration, 3.17 or higher is required) • NC551m Firmware version 2.104.356.3 or higher • NC553m Firmware version 3.104.356.3 or higher • CN1100E Firmware version 3.104.356.3 or higher • HP-UX 11i v3 OS Fusion version B.11.31.1103 or higher • HP-UX CommonIO 11.31.
Related information HP references The latest documentation for Fibre Channel cards is available in English at: http://www.hp.com/go/hpux-iocards-docs Other references Additional information about configuring and updating UEFI functionality on this product is available from the Emulex website: http://www.emulex.com/files/downloads/hardware/boot_manual.pdf Software availability in native languages This product is available only in the English language.
