FibrChanl-03 (fcoc) Fibre Channel Mass Storage Driver for HP-UX 11i v3 Release Notes Version Number B.11.31.1403 HP Part Number: 5900-3279 Published: March 2014 Edition: 1.
Contents FibrChanl-03 (fcoc) Fibre Channel Mass Storage Driver for HP-UX 11i v3 overview............................3 New and changed features in this release...................................................................................3 New features......................................................................................................................3 HP-UX 11i v3 March 2014 (AR1403) release.......................................................................
This document provides information about the B.11.31.1403 release of the FibrChanl-03 (fcoc) Fibre Channel Mass Storage Driver for HP-UX 11i v3. FibrChanl-03 (fcoc) Fibre Channel Mass Storage Driver for HP-UX 11i v3 overview This release of the document for the FibrChanl-03 (fcoc) Fibre Channel Mass Storage Driver for HP-UX 11i v3 (version B.11.31.1403) documents defect fixes and version changes.
Table 2 HP-UX October 2013 (AR1310) Fixes Defect ID Description QXCR1001270184 This fixes the issue where system hang is seen because of a memory leak on SD2 systems during continuous driver load and unload in a loop. QXCR1001295252 This fixes the issue where the description for the LOM on BL8xxc i4 servers as part of the ioscan output has an “N/A” string in the middle.
Table 5 HP-UX March 2012 (AR1203) Fixes (continued) Defect ID Description QXCR1001115144 This corrects an issue that may result in the FCOC driver hanging during unload. QXCR1001159730 This fixes an issue where the moduload fails to unload fc module because it is busy. QXCR1001171646 This corrects a system panic that may occur when a target path goes offline. QXCR1001175013 This change corrects a driver issue that intermittently caused an HBA hang during a reset sequence.
Table 8 HP-UX March 2011 (WEB1103) Fixes Defect ID Description QXCR1001070913 This release fixes a problem in which when a port is disabled, SNIA does not display any port or adapter attributes for other enabled ports. Table 9 HP-UX March 2011 (AR1103) Fixes Defect ID Description N/A This is the first general release. Table 10 HP-UX November 2010 (WEB1011) Fixes Defect ID Description N/A There are no known problems fixed in this version. NOTE: 11i v3.
• HP Virtual Connect FlexFabric 10Gb/24-Port Module firmware version A fix in AR1203 exposes an issue with the HP VC FlexFabric 10Gb/24-Port Module (QXCR1001194681) that causes fcmsutil to incorrectly display the Previous Topology as UNINITALIZED whenever the link goes down. Please see QXCR1001194681 for more information and the minimum firmware version required for the HP Virtual Connect FlexFabric 10Gb/24-Port Module when the fix becomes available.
2. 3. Select Emulex Configuration Utility Ver:X.XXXXX and press Enter. When the Emulex Configuration Utility screen is displayed with Emulex Configuration Setup Utility selected, press Enter. 4. A list of all the adapters in the system is displayed. Your list may vary depending on the installed adapters. Locate the adapter you want to configure. Use the up/down arrows on your keyboard to select it, and press Enter.
5. The Emulex Adapter Configuration Main Menu screen comes up. Select Set Boot From SAN. A Disable Enable menu is displayed. Use the arrow keys to select the Enable option and press Enter. The selection is updated to NVRAM and the current setting is displayed. 6. On the same Emulex Adapter Configuration Main Menu screen, select Back to Display Adapters and RECONNECT DEVICES and press Enter. Type s to save the changes. Exit the Emulex utility. Control B to go into cm and type rs to reset the system. 7.
• BL8x0c i2 System Firmware 15.05 or higher • Superdome2 System Firmware 2.26 or higher • rx2800 i2 System Firmware s26.21 or higher • C7000 OA Firmware 3.20 or higher • VCSU FW 1.6.0 or higher • VC-Enet FW Version 3.15 or higher (for profile migration, 3.17 or higher is required) • BL8x0c i4 LOM Firmware version 4.2.401.2212 or higher • NC551m Firmware version 4.2.401.2212 or higher • NC553m Firmware version 4.2.401.2212 or higher • CN1100E Firmware version 4.2.401.
servers with the HP-UX 11i v3 (B.11.31) operating system.
