Manualshelf

PCIe 4/8 GB 2 Port Fibre Channel QLogix Mezz HBA Install Guide, Edition 2, September 2010

ManualsBrandsHP ManualsNetwork HardwareHP Fibre Channel Host Bus Adapters
11121314151617181920
Example 3-4 Example of “ioscan” report of legacy hardware paths after installation
# ioscan -fnH 0/4/0/0/0/1
Class I H/W Path Driver S/W State H/W Type Description
========================================================================
fc 3 0/4/0/0/0/1 fcd CLAIMED INTERFACE HP 8Gb Dual Port PCIe Fibre Channel Mezzanine (FC
Port 2)
/dev/fcd3
fcp 0 0/4/0/0/0/1.105 fcd_fcp CLAIMED INTERFACE FCP Domain
ext_bus 2 0/4/0/0/0/1.105.0.9.0 fcd_vbus CLAIMED INTERFACE FCP Array Interface
target 21 0/4/0/0/0/1.105.0.9.0.0 tgt CLAIMED DEVICE
disk 3 0/4/0/0/0/1.105.0.9.0.0.0 sdisk CLAIMED DEVICE HP OPEN-V
/dev/dsk/c2t0d0 /dev/dsk/c2t0d0s2 /dev/rdsk/c2t0d0 /dev/rdsk/c2t0d0s2
/dev/dsk/c2t0d0s1 /dev/dsk/c2t0d0s3 /dev/rdsk/c2t0d0s1 /dev/rdsk/c2t0d0s3
disk 4 0/4/0/0/0/1.105.0.9.0.0.1 sdisk CLAIMED DEVICE HP OPEN-V
/dev/dsk/c2t0d1 /dev/rdsk/c2t0d1
disk 5 0/4/0/0/0/1.105.0.9.0.0.2 sdisk CLAIMED DEVICE HP OPEN-V
/dev/dsk/c2t0d2 /dev/rdsk/c2t0d2
disk 6 0/4/0/0/0/1.105.0.9.0.0.3 sdisk CLAIMED DEVICE HP OPEN-V
/dev/dsk/c2t0d3 /dev/rdsk/c2t0d3
disk 7 0/4/0/0/0/1.105.0.9.0.0.4 sdisk CLAIMED DEVICE HP OPEN-V
/dev/dsk/c2t0d4 /dev/rdsk/c2t0d4
Verifying connectivity
Once the HP Fibre Channel Mass Storage software and hardware are installed and running, use
the following steps to verify connectivity:
1. Check the state of all Fibre Channel hardware and interfaces. Enter the ioscan command
and verify the Hardware State and the hw Interface state are CLAIMED.
If the Fibre Channel device file has not been created, enter the following commands:
# insf -e
# ioscan -f
2. Verify that all devices you have attached to the Fibre Channel adapter are listed in the
ioscan output. For example, if you have a direct attach Fibre Channel device installed in
the system, the ioscan output may look like the following:
8/12.8.0.255.0.1.0 sdisk CLAIMED DEVICE DGC C3400WDR5
The example above is the hardware path of LUN0 of a directly attached Fibre Channel Mass
Storage device with a Loop ID of 1.
If all the attached devices are listed and appear as CLAIMED, the HP Fibre Channel Mass Storage
installation is verified.
If all the attached devices are not listed or appear as CLAIMED, see the Troubleshooting and
Maintenance chapter of the HP Fibre Channel Adapters Support Guide.
Interpreting hardware paths
The following examples illustrate the Fibre Channel hardware path format.
20 Installing the HP-UX Operating System Components