R211x-HP Flexfabric 11900 FCoE Configuration Guide

# Apply the QoS policy plcy to the outbound direction of interface Ten-GigabitEthernet 1/0/3.

[SwitchC] interface ten-gigabitethernet 1/0/3

[SwitchC-Ten-GigabitEthernet1/0/3] qos apply policy plcy outbound

[SwitchC-Ten-GigabitEthernet1/0/3] quit

# Map 802.1p priority 3 to local precedence 3 in the outbound direction. (This is the default

mapping, and you can modify the mapping as needed.)

[SwitchC] qos map-table dot1p-lp

[SwitchC-maptbl-out-dot1p-lp] import 3 export 3

[SwitchC-maptbl-out-dot1p-lp] quit

# Enable byte-count WRR on interface Ten-GigabitEthernet 1/0/3, and configure queue 3 to use

strict priority (SP) queuing.

[SwitchC] interface ten-gigabitethernet 1/0/3

[SwitchC-Ten-GigabitEthernet1/0/3] qos wrr byte-count

[SwitchC-Ten-GigabitEthernet1/0/3] qos wrr 3 group sp

# Enable interface Ten-GigabitEthernet 1/0/3 to automatically negotiate with its peer to decide

whether to enable PFC, enable PFC for 802.1p priority 3, and configure Ten-GigabitEthernet

1/0/3 to trust the 802.1p priority carried in packets.

[SwitchC-Ten-GigabitEthernet1/0/3] priority-flow-control auto

[SwitchC-Ten-GigabitEthernet1/0/3] priority-flow-control no-drop dot1p 3

[SwitchC-Ten-GigabitEthernet1/0/3] qos trust dot1p

[SwitchC-Ten-GigabitEthernet1/0/3] quit

# Create interface VFC 1, and configure it to operate in E mode.

[SwitchC] interface vfc 1

[SwitchC-Vfc1] fc mode e

# Bind interface VFC 1 to interface Ten-GigabitEthernet 1/0/1, and assign it to VSAN 1 as a trunk

port.

[SwitchC-Vfc1] bind interface ten-gigabitethernet 1/0/1

[SwitchC-Vfc1] port trunk vsan 1

[SwitchC-Vfc1] quit

# Assign interface Ten-GigabitEthernet 1/0/1 to VLAN 10 as a trunk port.

[SwitchC] interface ten-gigabitethernet 1/0/1

[SwitchC-Ten-GigabitEthernet1/0/1] port link-type trunk

[SwitchC-Ten-GigabitEthernet1/0/1] port trunk permit vlan 10

[SwitchC-Ten-GigabitEthernet1/0/1] quit

# Create interface VFC 2, and configure it to operate in E mode.

[SwitchC] interface vfc 2

[SwitchC-Vfc2] fc mode e

# Bind interface VFC 2 to interface Ten-GigabitEthernet 1/0/2, and assign it to VSAN 1 as a trunk

port.

[SwitchC-Vfc2] bind interface ten-gigabitethernet 1/0/2

[SwitchC-Vfc2] port trunk vsan 1

[SwitchC-Vfc2] quit

# Assign interface Ten-GigabitEthernet 1/0/2 to VLAN 10 as a trunk port.

[SwitchC] interface ten-gigabitethernet 1/0/2

[SwitchC-Ten-GigabitEthernet1/0/2] port link-type trunk

[SwitchC-Ten-GigabitEthernet1/0/2] port trunk permit vlan 10

[SwitchC-Ten-GigabitEthernet1/0/2] quit