R211x-HP Flexfabric 11900 Layer 2 - LAN Switching Configuration Guide

193
LLDP-MED trapping, 174
loop detection, 103, 105, 107
loop detec
tion protection action, 106
loop detec
tion protection action (global), 106
loop detec
tion protection action (Layer 2
aggregate interface), 106
loop detec
tion protection action (Layer 2
Ethernet interface), 106
loopbac
k interface, 16 , 16
MA
C address table, 21 , 22, 31
MA
C address table dynamic aging timer, 27
MA
C address table entry, 22
MA
C address table frame forwarding rule, 28
MA
C Information, 32, 34
MA
C Information change send interval, 33
MA
C Information mode, 33
MA
C Information queue length, 33
managemen
t Ethernet interface, 1
MS
T region, 78
M
ST region max hops, 80
MS
TP, 62, 74, 98
M
STP device priority, 80
M
STP root bridge, 79
M
STP root bridge device, 79
M
STP secondary root bridge, 79
M
STP secondary root bridge device, 79
n
ull interface, 16 , 17
por
t isolation, 59
por
t isolation (on LAN), 60
por
t-based VLAN, 114 , 119
pr
ivate VLAN, 121 , 122 , 123
pr
ivate VLAN (promiscuous mode), 123
pr
ivate VLAN (trunk promiscuous mode), 126
RS
TP, 62, 74 , 98
R
STP device priority, 80
R
STP root bridge, 79
R
STP root bridge device, 79
R
STP secondary root bridge, 79
R
STP secondary root bridge device, 79
se
rvice loopback group, 186 , 186 , 187
ST
P, 62, 74 , 98
S
TP BPDU transmission rate, 83
S
TP device priority, 80
S
TP Digest Snooping, 90, 91
S
TP edge port, 83
S
TP No Agreement Check, 92, 93
S
TP port link type, 87
S
TP port mode, 87
S
TP port path cost, 84, 85
S
TP port priority, 86
ST
P port role restriction, 96
S
TP protection functions, 94
S
TP root bridge, 79
S
TP root bridge device, 79
S
TP secondary root bridge, 79
S
TP secondary root bridge device, 79
S
TP switched network diameter, 80
S
TP TC-BPDU transmission restriction, 96
S
TP timeout factor, 82
ST
P timer, 81
VL
AN basic settings, 112
VL
AN interface basic settings, 113
VL
AN mapping, 141 , 14 5 , 14 8
VL
AN mapping (one-to-one), 14 6 , 14 8
VL
AN mapping (one-to-two), 147 , 150
VL
AN mapping (two-to-two), 147 , 15 0
connec
ting
Layer 2 Ethernet interface cable connection, 14
C
onverged Enhanced Ethernet. Use CEE
cost
STP path cost, 63
S
TP port path cost calculation standard, 84
S
TP port path cost configuration, 84, 85
CS
T
MST region connection, 71
cu
stomer
LLDP customer bridge mode, 161
CVL
AN
LAN switching QinQ configuration, 13 0 , 133 , 13 6
L
AN switching QinQ VLAN transparent
transmission configuration, 139
VL
AN mapping configuration, 141 , 145
VL
AN mapping implementation, 14 3
D
Da
ta Center
Bridging Exchange Protocol. Use DCBX
Ether
net. Use DCE
DCBX
configuration, 168 , 180