R211x-HP Flexfabric 11900 Security Command Reference
Table Of Contents
- Title Page
- Contents
- AAA commands
- General AAA commands
- aaa session-limit
- accounting command
- accounting default
- accounting lan-access
- accounting login
- authentication default
- authentication lan-access
- authentication login
- authentication super
- authorization command
- authorization default
- authorization lan-access
- authorization login
- authorization-attribute (ISP domain view)
- display domain
- domain
- domain default enable
- state (ISP domain view)
- Local user commands
- RADIUS commands
- accounting-on enable
- data-flow-format (RADIUS scheme view)
- display radius scheme
- display radius statistics
- key (RADIUS scheme view)
- nas-ip (RADIUS scheme view)
- primary accounting (RADIUS scheme view)
- primary authentication (RADIUS scheme view)
- radius nas-ip
- radius session-control enable
- radius scheme
- reset radius statistics
- retry
- retry realtime-accounting
- secondary accounting (RADIUS scheme view)
- secondary authentication (RADIUS scheme view)
- security-policy-server
- snmp-agent trap enable radius
- state primary
- state secondary
- timer quiet (RADIUS scheme view)
- timer realtime-accounting (RADIUS scheme view)
- timer response-timeout (RADIUS scheme view)
- user-name-format (RADIUS scheme view)
- vpn-instance (RADIUS scheme view)
- HWTACACS commands
- data-flow-format (HWTACACS scheme view)
- display hwtacacs scheme
- hwtacacs nas-ip
- hwtacacs scheme
- key (HWTACACS scheme view)
- nas-ip (HWTACACS scheme view)
- primary accounting (HWTACACS scheme view)
- primary authentication (HWTACACS scheme view)
- primary authorization
- reset hwtacacs statistics
- secondary accounting (HWTACACS scheme view)
- secondary authentication (HWTACACS scheme view)
- secondary authorization
- timer quiet (HWTACACS scheme view)
- timer realtime-accounting (HWTACACS scheme view)
- timer response-timeout (HWTACACS scheme view)
- user-name-format (HWTACACS scheme view)
- vpn-instance (HWTACACS scheme view)
- LDAP commands
- General AAA commands
- 802.1X commands
- MAC authentication commands
- Port security commands
- display port-security
- display port-security mac-address block
- display port-security mac-address security
- port-security authorization ignore
- port-security enable
- port-security intrusion-mode
- port-security mac-address security
- port-security mac-move permit
- port-security max-mac-count
- port-security ntk-mode
- port-security oui
- port-security port-mode
- port-security timer autolearn aging
- port-security timer disableport
- Password control commands
- display password-control
- display password-control blacklist
- password-control { aging | composition | history | length } enable
- password-control aging
- password-control alert-before-expire
- password-control complexity
- password-control composition
- password-control enable
- password-control expired-user-login
- password-control history
- password-control length
- password-control login idle-time
- password-control login-attempt
- password-control super aging
- password-control super composition
- password-control super length
- password-control update-interval
- reset password-control blacklist
- reset password-control history-record
- Public key management commands
- IPsec commands
- ah authentication-algorithm
- description
- display ipsec { ipv6-policy | policy }
- display ipsec sa
- display ipsec statistics
- display ipsec transform-set
- display ipsec tunnel
- encapsulation-mode
- esp authentication-algorithm
- esp encryption-algorithm
- ike-profile
- ipsec anti-replay check
- ipsec anti-replay window
- ipsec apply
- ipsec decrypt-check enable
- ipsec logging packet enable
- ipsec df-bit
- ipsec global-df-bit
- ipsec { ipv6-policy | policy }
- ipsec { ipv6-policy | policy } local-address
- ipsec sa global-duration
- ipsec sa idle-time
- ipsec transform-set
- local-address
- pfs
- protocol
- qos pre-classify
- remote-address
- reset ipsec sa
- reset ipsec statistics
- sa duration
- sa hex-key authentication
- sa hex-key encryption
- sa idle-time
- sa spi
- sa string-key
- security acl
- snmp-agent trap enable ipsec
- transform-set
- IKE commands
- authentication-algorithm
- authentication-method
- dh
- display ike proposal
- display ike sa
- dpd
- encryption-algorithm
- exchange-mode
- ike dpd
- ike identity
- ike invalid-spi-recovery enable
- ike keepalive interval
- ike keepalive timeout
- ike keychain
- ike limit
- ike nat-keepalive
- ike profile
- ike proposal
- inside-vpn
- keychain
- local-identity
- match local address (IKE keychain view)
- match local address (IKE profile view)
- match remote
- pre-shared-key
- priority (IKE keychain view)
- priority (IKE profile view)
- proposal
- reset ike sa
- reset ike statistics
- sa duration
- snmp-agent trap enable ike
- SSH commands
- SSH server commands
- display ssh server
- display ssh user-information
- sftp server enable
- sftp server idle-timeout
- ssh server acl
- ssh server authentication-retries
- ssh server authentication-timeout
- ssh server compatible-ssh1x enable
- ssh server dscp
- ssh server enable
- ssh server ipv6 acl
- ssh server ipv6 dscp
- ssh server rekey-interval
- ssh user
- SSH client commands
- SSH server commands
- IP source guard commands
- ARP attack protection commands
- Unresolvable IP attack protection commands
- ARP packet rate limit commands
- Source MAC-based ARP attack detection commands
- ARP packet source MAC consistency check commands
- ARP active acknowledgement commands
- Authorized ARP commands
- ARP detection commands
- ARP automatic scanning and fixed ARP commands
- ARP gateway protection commands
- ARP filtering commands
- uRPF commands
- Crypto engine commands
- FIPS commands
- Support and other resources
- Index
297
undo ip verify source
Default
The IPv4 source guard function is disabled on an interface.
Views
Layer 2 Ethernet interface view, Layer 3 Ethernet interface view, VLAN interface view
Predefined user roles
network-admin
mdc-admin
Parameters
ip-address: Filters packets by source IPv4 addresses. With this keyword specified, the IP source guard
function on the interface filters a received packet by using source IP addresses of the IPv4 source guard
binding entries. If a match is found, the interface forwards the packet. Otherwise, the interface discards
the packet.
ip-address mac-address: Filters packets by source IPv4 addresses and source MAC addresses. With this
keyword specified, the IP source guard function on the interface filters a received packet by using source
IP addresses and source MAC addresses of dynamic IPv4 source guard binding entries. If both the
source IP address and source MAC address of the packet match an entry, the interface forwards the
packet. Otherwise, the interface discards the packet.
mac-address: Filters packets by source MAC addresses. With this keyword specified, the IP source guard
function on the interface filters a received packet by using source MAC addresses of the IPv4 source
guard binding entries. If a match is found, the interface forwards the packet. Otherwise, the interface
discards the packet.
Usage guidelines
After you enable IPv4 source guard on an interface, IP source guard can perform the following
operations:
• Dynamically obtain IPv4 binding entries from other modules.
• Use static and dynamic IPv4 source guard binding entries to filter IPv4 packets on the interface.
If a packet matches a binding entry, IP source guard forwards the packet. Otherwise, it drops the packet.
The modules that provide dynamic binding information for IP source guard include DHCP relay, DHCP
snooping, and DHCP server. IP source guard uses the dynamic binding entries created by DHCP relay
and DHCP snooping to filter packets. The dynamic binding entries that IP source guard learns from DHCP
server modules are not used to filter packets, and they are used by other modules to provide security
services.
You cannot configure dynamic IPv4 source guard on a service loopback interface.
The keywords specified in the ip verify source command take effect only to dynamic IPv4 source guard
binding entries. They determine the information according to which the interface uses the dynamic IPv4
source guard binding entries to filter packets. For static IPv4 source guard binding entries, this command
only enables packet filtering on an interface. The interface filters packets according to the static IPv4
source guard binding entries configured by the ip source binding command, instead of the keywords
specified in the ip verify source command.
Examples
# Enable IPv4 source guard on Layer 2 Ethernet interface Ten-GigabitEthernet 1/0/1 to filter packets
received on the port by using source IPv4 and MAC addresses of IPv4 source guard binding entries.