R211x-HP Flexfabric 11900 Security Command Reference
Table Of Contents
- Title Page
- Contents
- AAA commands
- General AAA commands
- aaa session-limit
- accounting command
- accounting default
- accounting lan-access
- accounting login
- authentication default
- authentication lan-access
- authentication login
- authentication super
- authorization command
- authorization default
- authorization lan-access
- authorization login
- authorization-attribute (ISP domain view)
- display domain
- domain
- domain default enable
- state (ISP domain view)
- Local user commands
- RADIUS commands
- accounting-on enable
- data-flow-format (RADIUS scheme view)
- display radius scheme
- display radius statistics
- key (RADIUS scheme view)
- nas-ip (RADIUS scheme view)
- primary accounting (RADIUS scheme view)
- primary authentication (RADIUS scheme view)
- radius nas-ip
- radius session-control enable
- radius scheme
- reset radius statistics
- retry
- retry realtime-accounting
- secondary accounting (RADIUS scheme view)
- secondary authentication (RADIUS scheme view)
- security-policy-server
- snmp-agent trap enable radius
- state primary
- state secondary
- timer quiet (RADIUS scheme view)
- timer realtime-accounting (RADIUS scheme view)
- timer response-timeout (RADIUS scheme view)
- user-name-format (RADIUS scheme view)
- vpn-instance (RADIUS scheme view)
- HWTACACS commands
- data-flow-format (HWTACACS scheme view)
- display hwtacacs scheme
- hwtacacs nas-ip
- hwtacacs scheme
- key (HWTACACS scheme view)
- nas-ip (HWTACACS scheme view)
- primary accounting (HWTACACS scheme view)
- primary authentication (HWTACACS scheme view)
- primary authorization
- reset hwtacacs statistics
- secondary accounting (HWTACACS scheme view)
- secondary authentication (HWTACACS scheme view)
- secondary authorization
- timer quiet (HWTACACS scheme view)
- timer realtime-accounting (HWTACACS scheme view)
- timer response-timeout (HWTACACS scheme view)
- user-name-format (HWTACACS scheme view)
- vpn-instance (HWTACACS scheme view)
- LDAP commands
- General AAA commands
- 802.1X commands
- MAC authentication commands
- Port security commands
- display port-security
- display port-security mac-address block
- display port-security mac-address security
- port-security authorization ignore
- port-security enable
- port-security intrusion-mode
- port-security mac-address security
- port-security mac-move permit
- port-security max-mac-count
- port-security ntk-mode
- port-security oui
- port-security port-mode
- port-security timer autolearn aging
- port-security timer disableport
- Password control commands
- display password-control
- display password-control blacklist
- password-control { aging | composition | history | length } enable
- password-control aging
- password-control alert-before-expire
- password-control complexity
- password-control composition
- password-control enable
- password-control expired-user-login
- password-control history
- password-control length
- password-control login idle-time
- password-control login-attempt
- password-control super aging
- password-control super composition
- password-control super length
- password-control update-interval
- reset password-control blacklist
- reset password-control history-record
- Public key management commands
- IPsec commands
- ah authentication-algorithm
- description
- display ipsec { ipv6-policy | policy }
- display ipsec sa
- display ipsec statistics
- display ipsec transform-set
- display ipsec tunnel
- encapsulation-mode
- esp authentication-algorithm
- esp encryption-algorithm
- ike-profile
- ipsec anti-replay check
- ipsec anti-replay window
- ipsec apply
- ipsec decrypt-check enable
- ipsec logging packet enable
- ipsec df-bit
- ipsec global-df-bit
- ipsec { ipv6-policy | policy }
- ipsec { ipv6-policy | policy } local-address
- ipsec sa global-duration
- ipsec sa idle-time
- ipsec transform-set
- local-address
- pfs
- protocol
- qos pre-classify
- remote-address
- reset ipsec sa
- reset ipsec statistics
- sa duration
- sa hex-key authentication
- sa hex-key encryption
- sa idle-time
- sa spi
- sa string-key
- security acl
- snmp-agent trap enable ipsec
- transform-set
- IKE commands
- authentication-algorithm
- authentication-method
- dh
- display ike proposal
- display ike sa
- dpd
- encryption-algorithm
- exchange-mode
- ike dpd
- ike identity
- ike invalid-spi-recovery enable
- ike keepalive interval
- ike keepalive timeout
- ike keychain
- ike limit
- ike nat-keepalive
- ike profile
- ike proposal
- inside-vpn
- keychain
- local-identity
- match local address (IKE keychain view)
- match local address (IKE profile view)
- match remote
- pre-shared-key
- priority (IKE keychain view)
- priority (IKE profile view)
- proposal
- reset ike sa
- reset ike statistics
- sa duration
- snmp-agent trap enable ike
- SSH commands
- SSH server commands
- display ssh server
- display ssh user-information
- sftp server enable
- sftp server idle-timeout
- ssh server acl
- ssh server authentication-retries
- ssh server authentication-timeout
- ssh server compatible-ssh1x enable
- ssh server dscp
- ssh server enable
- ssh server ipv6 acl
- ssh server ipv6 dscp
- ssh server rekey-interval
- ssh user
- SSH client commands
- SSH server commands
- IP source guard commands
- ARP attack protection commands
- Unresolvable IP attack protection commands
- ARP packet rate limit commands
- Source MAC-based ARP attack detection commands
- ARP packet source MAC consistency check commands
- ARP active acknowledgement commands
- Authorized ARP commands
- ARP detection commands
- ARP automatic scanning and fixed ARP commands
- ARP gateway protection commands
- ARP filtering commands
- uRPF commands
- Crypto engine commands
- FIPS commands
- Support and other resources
- Index
78
undo secondary authorization [ { ipv4-address | ipv6 ipv6-address } [ port-number | vpn-instance
vpn-instance-name ]* ]
Default
No secondary HWTACACS authorization server is specified.
Views
HWTACACS scheme view
Predefined user roles
network-admin
mdc-admin
Parameters
ipv4-address: Specifies the IPv4 address of the secondary HWTACACS authorization server.
ipv6 ipv6-address: Specifies the IPv6 address of the secondary HWTACACS authorization server.
port-number: Specifies the service port number of the secondary HWTACACS authorization server, a
TCP port number in the range of 1 to 65535. The default setting is 49.
key { cipher | simple } string: Sets the shared key for secure communication with the secondary
HWTACACS authorization server.
• cipher string: Sets a ciphertext shared key. The string argument is case sensitive.
{ In non-FIPS mode, the key is a string of 1 to 373 characters.
{ In FIPS mode, the key is a string of 15 to 373 characters.
• simple string: Sets a plaintext shared key. The string argument is case sensitive.
{ In non-FIPS mode, the key is a string of 1 to 255 characters.
{ In FIPS mode, the key is a string of 15 to 255 characters and must contain digits, uppercase
letters, lowercase letters, and special characters.
single-connection: The device and the secondary HWTACACS authorization server use the same TCP
connection to exchange all authorization packets for all users. If you do not specify this keyword, the
device establishes a new TCP connection each time it exchanges authorization packets with the
secondary authorization server for a user. If the HWTACACS server supports the single-connection
method, HP recommends that you specify this keyword to reduce TCP connections for improving system
performance.
vpn-instance vpn-instance-name: Specifies the MPLS L3VPN to which the secondary HWTACACS
authorization server belongs, where vpn-instance-name is a case-sensitive string of 1 to 31 characters. If
the server is on the public network, do not specify this option.
Usage guidelines
Make sure that the port number and shared key settings of the secondary HWTACACS authorization
server are the same as those configured on the server.
You can configure up to 16 secondary HWTACACS authorization servers for an HWTACACS scheme.
If the primary server fails, the device tries to communicate with a secondary server in active state. The
device connects to the secondary servers in the order they are configured.
If you use the undo secondary authorization command without specifying any parameter, the command
removes all secondary authorization servers.