R211x-HP Flexfabric 11900 TRILL Configuration Guide

[RB1-Ten-GigabitEthernet5/0/5] trill enable

[RB1-Ten-GigabitEthernet5/0/5] trill link-type trunk

[RB1-Ten-GigabitEthernet5/0/5] quit

# Assign port Ten-GigabitEthernet 5/0/11 to VLAN 100.

[RB1] interface ten-gigabitethernet 5/0/11

[RB1-Ten-GigabitEthernet5/0/11] port access vlan 100

# Enable TRILL on port Ten-GigabitEthernet 5/0/11, and use the default TRILL link type access.

[RB1-Ten-GigabitEthernet5/0/11] trill enable

[RB1-Ten-GigabitEthernet5/0/11] quit

2. Configure RB2:

# Enable TRILL.

<RB2> system-view

[RB2] trill

[RB2-trill] quit

# Configure port Ten-GigabitEthernet 3/0/5 as a trunk port, assign the port to VLAN 100, and

configure VLAN 100 as the PVID of the port.

[RB2] interface ten-gigabitethernet 3/0/5

[RB2-Ten-GigabitEthernet3/0/5] port link-type trunk

[RB2-Ten-GigabitEthernet3/0/5] port trunk permit vlan 100

[RB2-Ten-GigabitEthernet3/0/5] port trunk pvid vlan 100

# Enable TRILL on port Ten-GigabitEthernet 3/0/5, and configure the TRILL link type as trunk.

[RB2-Ten-GigabitEthernet3/0/5] trill enable

[RB2-Ten-GigabitEthernet3/0/5] trill link-type trunk

[RB2-Ten-GigabitEthernet3/0/5] quit

# Configure the LSU1TGS48SF0 card in slot 3 to operate in port-extender mode, and reboot the

card.

[RB2] switch-mode port-extender slot 3

This command may need reboot the specified slot. Continue? [Y/N]:y

Process OK.

After the card is rebooted, extension ports FortyGigE 3/0/49 and FortyGigE 3/0/50 are visible.

# Configure extension port GigabitEthernet 3/0/49 as a trunk port, and assign the port to VLAN

100.

[RB2] interface fortygige 3/0/49

[RB2-FortyGigE3/0/49] port link-type trunk

[RB2-FortyGigE3/0/49] port trunk permit vlan 100

# Enable TRILL on extension port FortyGigE 3/0/49, and use the default TRILL link type access.

[RB2-FortyGigE3/0/49] trill enable

# Configure one-to-one VLAN mapping on extension port FortyGigE 3/0/49 to map VLAN 101

to VLAN 100.

[RB2-FortyGigE3/0/49] vlan mapping 101 translated-vlan 100

[RB2-FortyGigE3/0/49] quit

# Configure extension port FortyGigE 3/0/50 as a trunk port, and assign the port to VLAN 101.

[RB2] interface fortygige 3/0/50

[RB2-FortyGigE3/0/50] port link-type trunk

[RB2-FortyGigE3/0/50] port trunk permit vlan 101

# Disable STP on extension port FortyGigE 3/0/50.