R21xx-HP FlexFabric 11900 ACL and QoS Command Reference

35
O
p
tion Descri
p
tion
customer-dot1p
dot1p-value&<1-8>
Matches the 802.1p priority of the customer network.
The dot1p-value&<1-8> argument is a list of 802.1p priority values. An
802.1p priority is in the range of 0 to 7. &<1-8> indicates that you can enter
up to eight 802.1p priority values.
customer-vlan-id vlan-id-list
Matches the customer VLAN IDs (CVLANs).
The vlan-id-list argument is in the format of vlan-id-list = { vlan-id | vlan-id1 to
vlan-id2 }&<1-10>, where the vlan-id, vlan-id1, and vlan-id2 arguments
represent the VLAN IDs and each are in the range of 1 to 4094, vlan-id1
must be no greater than vlan-id2, and &<1-10> indicates that you can
specify up to 10 VLAN IDs or VLAN ID ranges.
destination-mac mac-address Matches a destination MAC address.
dscp dscp-value&<1-8>
Matches DSCP values.
The dscp-value&<1-8> argument is a list of DSCP values. A DSCP value is in
the range of 0 to 63 or can be a keyword shown Table 18. &<1-8> indicates
that you can enter up to eight DSCP values.
ip-precedence
ip-precedence-value&<1-8>
Matches IP precedence.
The ip-precedence-value&<1-8> argument is a list of IP precedence values.
An IP precedence is in the range of 0 to 7. &<1-8> indicates that you can
enter up to eight IP precedence values.
protocol protocol-name
Matches a protocol.
The protocol-name argument can be IP or IPv6.
qos-local-id local-id-value
Matches a local QoS ID in the range of 1 to 4095.
The switch supports local QoS IDs in the range of 1 to 3999.
service-dot1p
dot1p-value&<1-8>
Matches the 802.1p priority of the service provider network.
The dot1p-value&<1-8> argument is a list of 802.1p priority values. An
802.1p priority is in the range of 0 to 7. &<1-8> indicates that you can enter
up to eight 802.1p priority values.
service-vlan-id vlan-id-list
Matches the service provider VLAN IDs (SVLANs).
The vlan-id-list argument is in the format of vlan-id-list = { vlan-id | vlan-id1 to
vlan-id2 }&<1-10>, where the vlan-id, vlan-id1, and vlan-id2 arguments
represent the VLAN IDs and each are in the range of 1 to 4094, vlan-id1
must be no greater than vlan-id2, and &<1-10> indicates that you can
specify up to 10 VLAN IDs or VLAN ID ranges.
source-mac mac-address Matches a source MAC address.
Usage guidelines
When an ACL is referenced by a QoS policy for traffic classification, the action (permit or deny) in the
ACL is ignored, and the actions in the associated traffic behavior are performed.
If a class that uses the AND operator has multiple if-match acl, if-match acl ipv6, if-match
customer-vlan-id or if-match service-vlan-id clauses, a packet that matches any of the clauses matches
the class.
To successfully execute the traffic behavior associated with a traffic class that uses the AND operator,
define only one if-match clause for any of the following match criteria, and enter only one value for any
of the following list arguments (for example, the 8021p-list argument):