HP FlexFabric 5930 Switch Series Fundamentals Command Reference Part number: 5998-4564 Software version: Release 2406 & Release 2407P01 Document version: 6W101-20140404
Legal and notice information © Copyright 2014 Hewlett-Packard Development Company, L.P. No part of this documentation may be reproduced or transmitted in any form or by any means without prior written consent of Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice.
Contents Basic CLI commands ···················································································································································· 1 command-alias enable ············································································································································· 1 command-alias mapping ········································································································································· 1 displa
telnet server dscp ··················································································································································· 40 telnet server enable ··············································································································································· 41 telnet server ipv6 acl ············································································································································· 41 telnet
ftp ············································································································································································ 84 ftp client source ······················································································································································ 85 ftp client ipv6 source ·········································································································································
sha256sum ·························································································································································· 128 umount ·································································································································································· 129 undelete ································································································································································
display memory-threshold ··································································································································· 174 display power ······················································································································································ 175 display scheduler job ·········································································································································· 176 display scheduler
Basic CLI commands command-alias enable Use command-alias enable to enable the command keyword alias function. Use undo command-alias enable to disable the command keyword alias function. Syntax command-alias enable undo command-alias enable Default The command keyword alias function is disabled. Views System view Predefined user roles network-admin Usage guidelines Configured command keyword aliases take effect only when the command keyword alias function is enabled.
Views System view Predefined user roles network-admin Parameters cmdkey: Specifies the first keyword of a non-undo command or the second keyword of an undo command. You must enter the keyword in its complete form. alias: Specifies an alias for the keyword, a string of 1 to 20 characters. It must be different from the first keyword of any non-undo command and the second keyword of any undo command.
include: Displays all lines matching the specified regular expression. regular-expression: Specifies a regular expression, a case-sensitive string of 1 to 256 characters. Usage guidelines Use the | { begin | exclude | include } regular-expression option with a display command to filter the command output. For more information about regular expressions, see Fundamentals Configuration Guide. Examples # Display the lines that contain "vlan" in the running configuration.
# Display the first line that begins with "user-group" in the running configuration and all of the following lines. display current-configuration | by-linenum begin user-group 114: user-group system 115- # 116- return display > Use display > to save the output from a display command to a separate file. Syntax display command > filename Views Any view Predefined user roles network-admin network-operator Parameters command: Specifies the keywords and arguments of a display command.
Syntax display command >> filename Views Any view Predefined user roles network-admin network-operator Parameters command: Specifies the keywords and arguments of a display command. To display available keywords and arguments, enter display ?. filename: Specifies the name of the file that is used to save the output, a string of 1 to 63 characters. Usage guidelines The display commands show the configuration, statistics, and states of the device.
display command-alias Use display command-alias to display the status of the command keyword alias function and the configured command keyword alias. Syntax display command-alias Views Any view Predefined user roles network-admin network-operator Examples # Display command keyword alias information.
system-view vlan 2 quit Related commands history-command max-size display history-command all Use display history-command all to display all commands saved in the command history buffer for all CLI sessions. Syntax display history-command all Views Any view Predefined user roles network-admin network-operator Usage guidelines The system automatically saves commands successfully executed by users to the command history buffer for all CLI sessions. Users can view them and execute them again.
Predefined user roles network-admin network-operator Examples # Display hotkey information. display hotkey ----------------- Hotkeys -----------------Defined command hotkeysCTRL_G display current-configuration CTRL_L display ip routing-table CTRL_O undo debugging all -Undefined command hotkeysCTRL_T NULL CTRL_U NULL -System-reserved hotkeysCTRL_A Move the cursor to the beginning of the line. CTRL_B Move the cursor one character to the left. CTRL_C Stop the current command.
hotkey Use hotkey to assign a command to a configurable hotkey. Use undo hotkey to restore the default. Syntax hotkey { CTRL_G | CTRL_L | CTRL_O | CTRL_T | CTRL_U } command undo hotkey { CTRL_G | CTRL_L | CTRL_O | CTRL_T | CTRL_U } Default • Ctrl_G: display current-configuration (display the running configuration). • Ctrl_L: display ip routing-table (display the IPv4 routing table information). • Ctrl_O: undo debugging all (disable all debugging functions).
Syntax quit Views Any view Predefined user roles network-admin network-operator Usage guidelines Executing this command in user view disconnects you from the device. Examples # Return from FortyGigE 1/0/1 interface view to system view and then to user view. [Sysname-FortyGigE1/0/1] quit [Sysname] quit return Use return to return to user view from any other view.
Default The default depends on the configuration of the screen-length command in user line view. The following are default settings for the screen-length command: • Pausing between screens of output. • Displaying up to 24 lines on a screen. Views User view Predefined user roles network-admin Usage guidelines If you disable pausing between screens of output, all output is displayed and the screen is refreshed continuously until the final screen is displayed.
Login management commands Some login management commands are available in both user line view and user line class view: • A setting in user line view is applied only to the user line. A setting in user line class view is applied to all user lines of the class. • A non-default setting in either view takes precedence over a default setting in the other view. A non-default setting in user line view takes precedence over a non-default setting in user line class view.
Examples # Configure character s as the shortcut key for starting a terminal session on the AUX line. system-view [Sysname] line aux 0 [Sysname-line-aux0] activation-key s To verify the configuration: 1. Exit the console session. [Sysname-line-aux0] return quit 2. Log in again through the AUX line. The following message appears: Press ENTER to get started. 3. Press Enter. Pressing Enter does not start a session. 4. Enter s. A terminal session is started.
• If the setting of either command is not the default in VTY line view, the setting of the other command in VTY line view takes effect. • If the settings of both commands are the defaults in VTY line view, the settings of the commands in VTY line class view take effect. Examples # Enable the none authentication mode for user line VTY 0.
Predefined user roles network-admin Parameters command: Specifies the command to be automatically executed. Usage guidelines This command is not supported in AUX line view or AUX line class view. This command is available in both user line view and user line class view: • If the setting in user line view is not the default setting, the setting in user line view takes effect.
This operation is the same as directly logging in to the device at 192.168.1.41 through Telnet. When you break the Telnet connection to 192.168.1.41, the Telnet connection to 192.168.1.40 is broken at the same time. command accounting Use command accounting to enable command accounting. Use undo command accounting to restore the default. Syntax command accounting undo command accounting Default Command accounting is disabled, and the accounting server does not record executed commands.
undo command authorization Default Command authorization is disabled. Logged-in users can execute commands without authorization. Views User line view, user line class view Predefined user roles network-admin Usage guidelines When command authorization is enabled, a command is available only if the user has the commensurate user role and is authorized to use the command by the AAA scheme.
7: Uses seven data bits for each character. 8: Uses eight data bits for each character. Usage guidelines This command is not supported in VTY line view. This setting must be the same as that on the configuration terminal. Examples # Configure AUX 0 to use five data bits for each character. system-view [Sysname] line aux 0 [Sysname-line-aux0] databits 5 display line Use display line to display user line information.
A : Authentication use AAA. N : No authentication is required. P : Password authentication. Table 1 Command output Field Description Modem Whether the modem allows calling in or out. By default, this attribute is not configured and a hyphen (-) is displayed. # Display summary information about all user lines. display line summary Line type : [AUX] 0:UXXX XXXX XX Line type : [VTY] 10:UUXX XXXX XXXX XXXX 26:XXXX XXXX XXXX XXXX 42:XXXX XXXX XXXX XXXX 58:XXXX XXXX XXXX XXXX 2 lines used.
display telnet client The source IP address is 1.1.1.1. The output shows that the device uses the source IPv4 address 1.1.1.1 for outgoing Telnet packets when it serves as a Telnet client. Related commands telnet client source display user-interface Use display user-interface to display user line information.
N : No authentication is required. P : Password authentication. Table 3 Command output Field Description Modem Whether the modem allows calling in or out. By default, this attribute is not configured and a hyphen (-) is displayed. # Display summary information about all user lines. display user-interface summary Line type : [AUX] 0:UXXX XXXX XX Line type : [VTY] 10:UUXX XXXX XXXX XXXX 26:XXXX XXXX XXXX XXXX 42:XXXX XXXX XXXX XXXX 58:XXXX XXXX XXXX XXXX 2 lines used.
display users Idx Line Idle Time Pid Type 10 VTY 0 00:10:49 Jun 11 11:27:32 320 TEL + 11 VTY 1 00:00:00 Jun 11 11:39:40 334 TEL Following are more details. VTY 0 : Location: 192.168.1.12 VTY 1 : Location: 192.168.1.26 + : Current operation user. F : Current operation user works in async mode. The output shows that two users have logged in to the device: one is using user line VTY 0 and the other (yourself) is using VTY 1. Your IP address is 192.168.1.26.
default: Restores the default escape key sequence Ctrl+C. Usage guidelines Some commands might take a long time to complete in some situations, for example, when the ping command has 1000 packets to send or when the tracert command is used for an unreachable destination. Before such a command is completed, you can stop the command by pressing the shortcut key for terminating tasks. Whether a command can be terminated by Ctrl+C by default depends on the software implementation of the command.
Syntax flow-control { hardware | none | software } undo flow-control Default The flow control mode is none. Views User line view Predefined user roles network-admin Parameters hardware: Performs hardware flow control. none: Disables flow control. software: Performs software flow control. Usage guidelines This command is not supported in VTY line view.
Parameters number1: Specifies the absolute number of a user line, in the range of 0 to 73. This number typically starts from 0. aux: Specifies the AUX line. vty: Specifies the VTY line. number2: Specifies the relative number of a user line. The value range is 0 to 9 for the AUX line and 0 to 63 for the VTY line. Usage guidelines This command does not release the line you are using. Examples # Release user line VTY 1: 1. Display online users.
vty: Specifies the VTY line. number2: Specifies the relative number of a user line. The value range is 0 to 9 for the AUX line and 0 to 63 for the VTY line. Usage guidelines This command does not release the line you are using. This is an older command reserved for backward compatibility purposes. Although it has the same functionality and output as the free line command, HP recommends you use the free line command. Examples # Release user line VTY 1: 1. Display online users.
Usage guidelines Each user line uses a separate command history buffer to save commands successfully executed by its user. The size of the buffer determines how many history commands the buffer can store. To view stored history commands on your user line, press the up arrow key or down arrow key or execute the display history-command command. Terminating a CLI session clears the commands in the history buffer.
• If the setting in user line view is the default setting but the setting in user line class view is not, the setting in user line class view takes effect. Examples # Set the idle timeout to 1 minute and 30 seconds for user line AUX 0. system-view [Sysname] line aux 0 [Sysname-line-aux0] idle-timeout 1 30 line Use line to enter one or multiple user line views.
Related commands line class line class Use line class to enter user line class view. Syntax line class { aux | vty } Views System view Predefined user roles network-admin Parameters aux: Specifies the AUX line class view. vty: Specifies the VTY line class view. Usage guidelines To configure the same settings for all user lines of a line class, use this command to enter the user line class view.
To verify the configuration: 1. Exit the console session. [Sysname-line-aux0] return quit 2. Log in again through the AUX line. The following message appears: Press ENTER to get started. 3. Press Enter. Pressing Enter does not start a session. 4. Enter s. A terminal session is started. Related commands line lock Use lock to lock the current user line. This method prevents unauthorized users from using the user line.
locked ! // The user line is locked. To unlock it, press Enter and enter the password: Password: parity Use parity to specify a parity check mode. Use undo parity to restore the default. Syntax parity { even | mark | none | odd | space } undo parity Default The setting is none, and no parity check is performed. Views User line view Predefined user roles network-admin Parameters even: Performs even parity check. mark: Performs mark parity check. none: Disables parity check.
Syntax protocol inbound { all |ssh | telnet } undo protocol inbound Default Both protocols are supported. Views VTY line view, VTY line class view Predefined user roles network-admin Parameters all: Supports both protocols. ssh: Supports SSH only. telnet: Supports Telnet only. Usage guidelines This configuration is effective only for a user who logs in through the user line after the configuration is completed.
Views User line view, user line class view Predefined user roles network-admin Parameters screen-length: Specifies the maximum number of lines to be displayed on a screen, in the range of 0 to 512. Setting this argument to 0 disables pausing between screens of output. Usage guidelines This command sets the maximum number of lines that can be displayed on one screen when the screen pause function is enabled. If the screen pause function is disabled, the system displays command output without any pause.
number1: Specifies the absolute number of a user line, in the range of 0 to 73. This number typically starts from 0. aux: Specifies the AUX line. vty: Specifies the VTY line. number2: Specifies the relative number of a user line. The value range is 0 to 9 for the AUX line and 0 to 63 for the VTY line. Usage guidelines To end a message, press Enter. To cancel a message and return to user view, press Ctrl+C. Examples # Before you restart the device, send a notification to VTY 1 to inform the user.
password: Specifies the password string. This argument is case sensitive. If simple is specified, it must be a string of 1 to 16 characters. If hash is specified, it must be a string of 1 to 110 characters. Usage guidelines For security purposes, the password is hashed before being saved, whether you specify the hash or simple keyword.
Examples # Disable the terminal service for user line VTY 0 through VTY 4 so no user can log in to the device through the user lines. system-view [Sysname] line vty 0 4 [Sysname-line-vty0-4] undo shell Disable ui-vty0-4 , are you sure? [Y/N]:y [Sysname-line-vty0-4] speed Use speed to set the transmission rate (also called the "baud rate") on a user line. Use undo speed to restore the default. Syntax speed speed-value undo speed Default The transmission rate is 9600 bps.
undo stopbits Default One stop bit is used. Views User line view Predefined user roles network-admin Parameters 1: Uses one stop bit. 1.5: Uses one and a half stop bits. The device does not support using one and a half stop bits. If you specify this keyword, two stop bits are used. 2: Uses two stop bits. Usage guidelines This command is not supported in VTY line view. The configuration terminal and the device must be configured to use the same number of stop bits to communicate.
source: Specifies a source IPv4 address or source interface for outgoing Telnet packets. interface interface-type interface-number: Specifies the source interface. The primary IPv4 address of the interface will be used as the source IPv4 address for outgoing Telnet packets. ip ip-address: Specifies the source IPv4 address for outgoing Telnet packets. dscp dscp-value: Specifies the DSCP value for IP to use in outgoing Telnet packets to indicate the packet transmission priority, in the range of 0 to 63.
Examples # Set the source IPv4 address for outgoing Telnet packets to 1.1.1.1 when the device serves as a Telnet client. system-view [Sysname] telnet client source ip 1.1.1.1 Related commands display telnet client configuration telnet ipv6 Use telnet ipv6 to Telnet to a host in an IPv6 network.
Syntax telnet server acl acl-number undo telnet server acl Default No ACL is used to filter Telnet logins. Views System view Predefined user roles network-admin Parameters acl-number: Specifies an ACL by its number: • Basic ACL—2000 to 2999. • Advanced ACL—3000 to 3999. • Ethernet frame header ACL—4000 to 4999. Usage guidelines Only one ACL can be used to filter Telnet logins, and only users permitted by the ACL can Telnet to the device.
Predefined user roles network-admin Parameters dscp-value: Specifies a DSCP value in the range of 0 to 63. Usage guidelines The DSCP value is carried in the ToS field of an IP packet, and it indicates the transmission priority of the packet. Examples # Set the DSCP value for IPv4 to use for outgoing Telnet packets to 30 on a Telnet server. system-view [Sysname] telnet server dscp 30 telnet server enable Use telnet server enable to enable the Telnet server function.
Default No ACL is used to filter IPv6 Telnet logins. Views System view Predefined user roles network-admin Parameters acl-number: Specifies an IPv6 ACL by its number: • Basic ACL—2000 to 2999. The ipv6 option is required. • Advanced ACL—3000 to 3999. The ipv6 option is required. • Ethernet frame header ACL—4000 to 4999. Do not specify the ipv6 option. Usage guidelines If the ACL does not exist or does not have a rule, all users are permitted to Telnet to the device.
Parameters dscp-value: Specifies a DSCP value in the range of 0 to 63. Usage guidelines The DSCP value is carried in the Traffic class field of an IPv6 packet, and it indicates the transmission priority of the packet. Examples # Set the DSCP value for IPv6 to use for outgoing Telnet packets to 30 on a Telnet server. system-view [Sysname] telnet server ipv6 dscp 30 terminal type Use terminal type to specify the terminal display type. Use undo terminal type to restore the default.
Syntax user-interface { first-number1 [ last-number1 ] | { aux | vty } first-number2 [ last-number2 ] } Views System view Predefined user roles network-admin Parameters first-number1: Specifies the absolute number of the first user line, in the range of 0 to 73. This number typically starts from 0. last-number1: Specifies the absolute number of the last user line. This number cannot be smaller than first-number1. aux: Specifies the AUX line. vty: Specifies the VTY line.
Views System view Predefined user roles network-admin Parameters aux: Specifies the AUX line class view. vty: Specifies the VTY line class view. Usage guidelines To configure the same settings for all user lines of a line class, use this command to enter the user line class view. Some login management commands are available in both user line view and user line class view: • A setting in user line view is applied only to the user line.
The following message appears: Press ENTER to get started. 3. Press Enter. Pressing Enter does not start a session. 4. Enter s. A terminal session is started. Related commands user-interface user-role Use user-role to assign a user role to a user line so users logged in through the user line get the user role at login. Use undo user-role to remove a user role or restore the default.
RBAC commands description Use description to configure a description for a user role. Use undo description to delete the description of a user role. Syntax description text undo description Default A user role has no description. Views User role view Predefined user roles network-admin Parameters text: User role description, a case-sensitive string of 1 to 128 characters. Examples # Configure the description "labVIP" for the user role role1.
Parameters name role-name: Specifies a user role name, a case-sensitive string of 1 to 63 characters. Usage guidelines If no user role name is specified, the command displays information about all user roles, including the predefined user roles. Examples # Display information about the user role 123.
Field Description VPN instance policy of the user role: VPN instance policy • deny—Denies access to any VPN except permitted VPNs. • permit (default)—Default VPN instance policy, which enables the user role to access any VPN instance. Permitted VPN instances VPNs accessible to the user role. User role rule number. Rule A user role rule specifies the permission to access a command or a set of commands. Predefined user role rules are identified by sys-n, where n represents an integer.
Parameters name feature-name: Displays the commands of a feature. The feature-name argument specifies the feature name, and all its letters must be lower case. verbose: Displays the commands of each feature. Usage guidelines If neither name feature-name nor verbose is specified, the display role feature command displays only the list of features available in the system. Examples # Display the list of feature names.
system-view ; clock timezone * (W) system-view ; clock summer-time * (W) system-view ; configuration replace file * system-view ; transceiver * system-view ; fan prefer-direction * (W) system-view ; system-working-mode * (W) system-view ; archive configuration * (W) system-view ; configuration encrypt * (W) system-view ; usb disable (W) system-view ; clock protocol * (W) system-view ; restore factory-default system-view ; rtm * (W) (W) system-view ; rtm * ; action * (W) system-view ; r
super * (X) display password-control * reset password-control * (R) (W) system-view ; password-control * (W) Table 7 Command output (display role feature name aaa) Field Description Feature Displays the name and brief function description of the feature. system-view ; domain * All the commands that start with domain in system view and all the commands in ISP domain view. system-view ; header * All the commands that start with header in system view.
Predefined user roles network-admin network-operator Parameters name feature-group-name: Specifies a feature group. The feature-group-name argument represents the feature group name, a case-sensitive string of 1 to 31 characters. If no feature group is specified, the command displays information about all feature groups. verbose: Displays the commands of each feature in the specified feature group.
Usage guidelines Repeat the feature command to add multiple features to a feature group. Examples # Add the security features AAA and ACL to the security group security-features.
Examples # Deny the user role role1 to access any interface. system-view [Sysname] role name role1 [Sysname-role-role1] interface policy deny [Sysname-role-role1-ifpolicy] quit # Deny the user role role1 to access any interface but FortyGigE 1/0/1 to FortyGigE 1/0/5.
• Specify them in a feature command. The create and remove operations are available only to logical interfaces. You can repeat the permit interface command to add permitted interfaces to a user role interface policy. The undo permit interface command removes the entire list of permitted interfaces if no interface is specified. Any change to a user role interface policy takes effect only on users who log in with the user role after the change.
Syntax permit vlan vlan-id-list undo permit vlan [ vlan-id-list ] Default No permitted VLANs are configured in user role interface policy view. Views User role VLAN policy Predefined user roles network-admin Parameters vlan-id-list: Specifies a space-separated list of up to 10 VLAN items. Each VLAN item specifies a VLAN by its VLAN ID or a range of VLANs in the form of vlan-id1 to vlan-id2. The value range for the VLAN IDs is 1 to 4094.
[Sysname] vlan 101 Permission denied. Related commands • display role • role • vlan policy deny permit vpn-instance Use permit vpn-instance to configure a list of VPNs accessible to a user role. Use undo permit vpn-instance to disable the access of a user role to specific VPNs. Syntax permit vpn-instance vpn-instance-name&<1-10> undo permit vpn-instance [ vpn-instance-name&<1-10> ] Default No permitted VPNs are configured in user role VPN instance policy.
Verify that you cannot use the user role to work on any VPN but VPN 1: # Verify that you can enter VPN1 view. system-view [Sysname] ip vpn-instance vpn1 [Sysname-vpn-instance-vpn1] # Verify that you can assign the primary accounting server at 10.110.1.2 to the VPN in the RADIUS scheme radius1. system-view [Sysname] radius scheme radius1 [Sysname-radius-radius1] primary accounting 10.110.1.2 vpn-instance vpn1 # Verify that you cannot create the VPN vpn2 or enter its view.
You cannot delete the predefined user roles or change the permissions assigned to network-admin, network-operator, or level-15. Level-0 to level-14 users can modify their own permissions for any commands except for the display history-command all command. Examples # Create the user role role1 and enter its view.
[Sysname] role default-role enable Related commands role role feature-group Use role feature-group to create a user role feature group and enter user role feature group view. Use undo role feature-group to delete a user role feature group. Syntax role feature-group name feature-group-name undo role feature-group name feature-group-name Default Two user role feature groups, L2 and L3, are created.
Syntax rule number { deny | permit } { command command-string | { execute | read | write } * { feature [ feature-name ] | feature-group feature-group-name } } undo rule { number | all } Default A user-defined user role has no rules and cannot use any command. Views User role view Predefined user roles network-admin Parameters number: Specifies a rule number in the range of 1 to 256. deny: Denies access to any specified command. permit: Permits access to any specified command.
• If two user-defined rules of the same type conflict, the one with the higher ID takes effect. For example, if rule 1 permits the ping command, rule 2 permits the tracert command, and rule 3 denies the ping command, the user role can use the tracert command but not the ping command. • If a predefined user role rule and a user-defined user role rule conflict, the user-defined user role rule takes effect.
Rule To control the access to a command, you must specify the command immediately after the view that has the command. Do not include the vertical bar (|), greater-than sign (>), or double greater-than sign (>>) when you specify display commands in a user role command rule. Guidelines To control access to a command, you must specify the command immediately behind the view to which the command is assigned. The rules that control command access for any subview do not apply to the command.
Syntax super [ rolename ] Views User view Predefined user roles network-admin Parameters rolename: Specifies a user role, a case-sensitive string of 1 to 63 characters. The user role must exist in the system. If no user role is specified, this command authorizes you the user role network-admin. Usage guidelines To enable users to obtain the user role that they are not logged in with, you must configure user role authentication.
Predefined user roles network-admin Parameters local: Enables local password authentication. scheme: Enables remote AAA authentication. Usage guidelines The authentication setting applies only to AUX and VTY users. An AUX user can obtain the user role without authentication. For local password authentication, use the super password command to set a password. For remote AAA authentication, set the username and password on the RADIUS or HWTACACS server.
Views System view Predefined user roles network-admin Parameters role rolename: Specifies a user role, a case-sensitive string of 1 to 63 characters. The user role must exist in the system. If no user role is specified, this command sets a password for user role network-admin. hash: Sets a hashed password. simple: Sets a plaintext password. This password will be saved in hashed text for security purposes. password: Specifies the password string. This argument is case sensitive.
Predefined user roles network-admin Usage guidelines The vlan policy deny command denies the access of a user role to any VLAN. To restrict the VLAN access of a user role to only a set of VLANs: 1. Use vlan policy deny to deny access to any VLAN. 2. Use permit vlan to specify accessible VLANs. To perform any of the following operations, you must make sure the VLAN is permitted by the VLAN policy of any user role that you are logged in with: • Create, remove, or configure a VLAN. • Enter its view.
Predefined user roles network-admin Usage guidelines The vpn-instance policy deny command denies the access of a user role to any VPN. To restrict the VPN access of a user role to only a set of VPNs: 1. Use vpn-instance policy deny to deny access to any VPN. 2. Use permit vpn-instance to specify accessible VPNs.
FTP commands FTP server commands display ftp-server Use display ftp-server to display FTP server configuration and status information. Syntax display ftp-server Views Any view Predefined user roles network-admin network-operator Examples # Display FTP server configuration and status information. display ftp-server FTP server is running. User count: 1 Idle-timeout timer (in minutes): 30 Table 9 Command output Field Description User count Number of the current logged-in users.
Predefined user roles network-admin network-operator Examples # Display detailed information about logged-in FTP users. display ftp-user UserName HostIP Port HomeDir root 192.168.20.184 46539 flash: If a username exceeds 10 characters, a host IP address exceeds 15 bits, or a directory name exceeds 37 bits, the exceeded part is displayed in the next line and right justified, as shown below.
Are you sure to free FTP connection? [Y/N]:y free ftp user-ip Use free ftp user-ip to manually release the FTP connections established from a specific IPv4 address. Syntax free ftp user-ip ipv4-address [ port port ] Views User view Predefined user roles network-admin Parameters ipv4-address: Specifies the source IP address of an FTP connection. You can use the display ftp-user command to view the source IP addresses of FTP connections.
ftp server acl Use ftp server acl to use an ACL to control FTP clients' access to the FTP server. Use undo ftp server acl to restore the default. Syntax ftp server acl { acl-number | ipv6 acl-number6 } undo ftp server acl [ ipv6 ] Default No ACL is used to control FTP clients' access to the FTP server. Views System view Predefined user roles network-admin Parameters acl-number: Specifies an IPv4 ACL number in the range of 2000 to 3999.
Views System view Predefined user roles network-admin Parameters dscp-value: Specifies a DSCP value in the range of 0 to 63. Usage guidelines The DSCP value is carried in the ToS field of an IP packet, and it indicates the transmission priority of the packet. Examples # Set the DSCP value for IPv4 to use for outgoing FTP packets to 30 on an FTP server. system-view [Sysname] ftp server dscp 30 ftp server enable Use ftp server enable to enable the FTP server.
Default IPv6 uses the DSCP value 0 for outgoing FTP packets on an FTP server. Views System view Predefined user roles network-admin Parameters dscp-value: Specifies a DSCP value in the range of 0 to 63. Usage guidelines The DSCP value is carried in the Traffic class field of an IPv6 packet, and it indicates the transmission priority of the packet. Examples # Set the DSCP value for IPv6 to use for outgoing FTP packets to 30 on an FTP server.
Related commands • ftp server enable • ssl server-policy (Security Command Reference) ftp timeout Use ftp timeout to set the idle-timeout interval for FTP connections. Use undo ftp timeout to restore the default. Syntax ftp timeout minute undo ftp timeout Default The FTP idle-timeout interval is 30 minutes. Views System view Predefined user roles network-admin Parameters Minute: Specifies an idle-timeout interval in the range of 1 to 35791 minutes.
Views FTP client view Predefined user roles network-admin Parameters localfile: Specifies a local file on the FTP client. remotefile: Specifies a remote file on the FTP server. Usage guidelines You can perform this operation only after you log in to the FTP server. Examples # Append the content of the local a.txt file to the b.txt file on the FTP server. ftp> append a.txt b.txt local: a.txt remote: b.txt 150 Connecting to port 50190 226 File successfully transferred 1657 bytes sent in 0.
Related commands binary binary Use binary to set the file transfer mode to binary, which is also called the "flow mode." Syntax binary Default The file transfer mode is ASCII. Views FTP client view Predefined user roles network-admin Usage guidelines You can perform this operation only after you log in to the FTP server. The carriage return characters vary with operating systems. For example, HP and Windows use /r/n, and Linux uses /n.
Examples # Terminate the connection to the FTP server and return to user view. ftp> bye 221-Goodbye. You uploaded 2 and downloaded 2 kbytes. 221 Logout. Related commands quit cd Use cd to change the current working directory to another directory on the FTP server. Syntax cd { directory | ..
ftp> cd / 250 OK. Current directory is / Related commands • cdup • pwd cdup Use cdup to enter the upper directory of the FTP server. This command does not change the working directory if the current directory is the FTP root directory. Syntax cdup Views FTP client view Predefined user roles network-admin Usage guidelines You can perform this operation only after you log in to the FTP server. Examples # Change the working directory to the upper directory.
Examples # Terminate the connection to the FTP server without exiting the FTP client view. ftp> close 221-Goodbye. You uploaded 0 and downloaded 0 kbytes. 221 Logout. ftp> Related commands disconnect debug Use debug to enable or disable FTP client debugging. Syntax debug Default FTP client debugging is disabled. Views FTP client view Predefined user roles network-admin Usage guidelines When FTP client debugging is enabled, executing this command disables FTP client debugging.
Table 11 Command output Field Description FTP command. • 2—IPv6 (1 for IPv4). • 8::124—IPv6 address of the FTP server. • 50198—Port number of the FTP server. ---> EPRT |2|8::124|50198| 200 PORT command successful Received FTP reply code. 200 represents the reply code, defined in RFC 959. ---> RETR a.txt Downloads file a.txt. delete Use delete to permanently delete a file on the FTP server.
Predefined user roles network-admin Parameters remotefile: Specifies the name of a file or directory on the FTP server. localfile: Specifies the name of the local file used for saving the displayed information. Usage guidelines You can perform this operation only after you log in to the FTP server. In FTP client view, executing the dir command is the same as executing the ls command. Examples # Display detailed information about the files and subdirectories in the current directory on the FTP server.
Syntax disconnect Views FTP client view Predefined user roles network-admin Usage guidelines You can perform this operation only after you log in to the FTP server. Examples # Terminate the connection to the FTP server without exiting the FTP client view. ftp> disconnect 221-Goodbye. You uploaded 0 and downloaded 0 kbytes. 221 Logout. ftp> Related commands close display ftp client source Use display ftp client source to display the source address settings on the FTP client.
Predefined user roles network-admin Parameters ftp-server: Specifies the IPv4 address or host name of an FTP server. A host name can be a case-insensitive string of 1 to 253 characters. Valid characters for a host name include letters, digits, hyphens (-), underscores (_), and dots (.). service-port: Specifies the TCP port number of the FTP server, in the range of 0 to 65535. The default value is 21. vpn-instance vpn-instance-name: Specifies the VPN instance to which the FTP server belongs.
Use undo ftp client source to restore the default. Syntax ftp client source { interface interface-type interface-number | ip source-ip-address } undo ftp client source Default No source IPv4 address is configured for outgoing FTP packets. The device uses the primary IPv4 address of the output interface for the route to the server as the source IP address.
Default No source address is configured. The device automatically selects a source IPv6 address as defined in RFC 3484. Views System view Predefined user roles network-admin Parameters interface interface-type interface-number: Specifies the source interface by its type and number. The IPv6 address configured on the source interface is the source address of outgoing FTP packets. Make sure the interface is up. Otherwise, the transmission fails.
service-port: Specifies the TCP port number of the FTP server, in the range of 0 to 65535. The default value is 21. dscp dscp-value: Specifies the DSCP value for IPv6 to use in outgoing FTP packets to indicate the packet transmission priority, in the range of 0 to 63. The default is 0. source { ipv6 source-ipv6-address | interface interface-type interface-number }: Specifies the source address used to establish the FTP connection.
Predefined user roles network-admin Parameters remotefile: Specifies the name of the file to be downloaded. localfile: Specifies a name for the downloaded file. Usage guidelines You can perform this operation only after you log in to the FTP server. To save the downloaded file to the working directory accessed by the ftp command, the localfile argument must specify a file name such as a.cfg. If you do not provide the localfile argument, the downloaded file uses its original name.
Usage guidelines In FTP client view, executing the help command is the same as entering?. Examples # Display all commands supported by the FTP client. ftp> help Commands may be abbreviated. Commands are: append delete ls quit rmdir ascii debug mkdir reget status binary dir newer rstatus system bye disconnect open rhelp user cd get passive rename verbose cdup help put reset ? close lcd pwd restart # Display the help information for the dir command.
ls Use ls to display detailed information about the files and subdirectories under the current directory on the FTP server. Use ls remotefile to display detailed information about a specific file or directory on the FTP server. Use ls remotefile localfile to save detailed information about a specific file or directory on the FTP server to a local file.
# Display the content of file s.txt. ftp> bye 221-Goodbye. You uploaded 0 and downloaded 2 kbytes. 221 Logout. more s.txt -rwxr-xr-x 1 0 0 1481 Jul 7 12:34 a.txt Related commands dir mkdir Use mkdir to create a subdirectory in the current directory on the FTP server. Syntax mkdir directory Views FTP client view Predefined user roles network-admin Parameters directory: Specifies the name of the directory to be created.
Usage guidelines You can perform this operation only after you log in to the FTP server. If the local file does not exist, this command downloads the file from the FTP server and saves it locally. If the remote file on the FTP server is not newer than the local file, this command does not update the local file. Examples # Update the local file with the file a.txt on the FTP server. ftp> newer a.txt local: a.txt remote: a.
ftp> passive Use passive to set the FTP operation mode to passive. Syntax passive Default The FTP operation mode is passive. Views FTP client view Predefined user roles network-admin Usage guidelines FTP can operate in either of the following modes: • Active mode—The FTP server initiates the TCP connection. • Passive mode—The FTP client initiates the TCP connection. You can use this command multiple times to change between active and passive modes.
Usage guidelines You can perform this operation only after you log in to the FTP server. To upload a file in the working directory accessed by the ftp command, the localfile argument must specify a file name such as a.cfg. To upload a file in some other directory, the localfile argument must specify the target directory plus the file name such as flash:/subdirectory/a.cfg. Otherwise, the command fails to take effect. Examples # Upload the file a.
quit Use quit to terminate the connection to the FTP server and return to user view. Syntax quit Views FTP client view Predefined user roles network-admin Examples # Terminate the connection to the FTP server and return to user view ftp> quit 221-Goodbye. You uploaded 0 and downloaded 0 kbytes. 221 Logout. Related commands bye reget Use reget to get the missing part of a file from the FTP server.
150-Connecting to port 47429 150 38143.3 kbytes to download 226 File successfully transferred 39058742 bytes received in 66.2 seconds (576.1 kbyte/s) rename Use rename to rename a file. Syntax rename [ oldfilename [ newfilename ] ] Views FTP client view Predefined user roles network-admin Parameters oldfilename: Specifies the original file name. newfilename: Specifies the new file name. Usage guidelines You can perform this operation only after you log in to the FTP server.
Views FTP client view Predefined user roles network-admin Examples # Clear the reply information received from the FTP server. ftp> reset restart Use restart to specify the marker to retransmit a file. Syntax restart marker Views FTP client view Predefined user roles network-admin Parameters marker: Specifies the retransmit marker. Usage guidelines You can perform this operation only after you log in to the FTP server. Support for this command varies with FTP servers.
Syntax rhelp [ protocol-command ] Views FTP client view Predefined user roles network-admin Parameters protocol-command: Specifies an FTP-related command. Usage guidelines You can perform this operation only after you log in to the FTP server. Examples # Display the FTP-related commands supported by the FTP.
Field Description EPRT Active mode (IPv6). PASV Passive mode (IPv4). EPSV Passive mode (IPv6). REST Restarts. RETR Downloads files. STOR Uploads files. APPE Appends uploading. DELE Deletes files. MKD Creates folders. XMKD Extended command with the meaning of MKD. RMD Removes folders. XRMD Extended command with the meaning of RMD. ABOR Aborts the transmission. SIZE Size of the transmission file. RNFR Original name. RNTO New name.
ftp>rmdir subdir1 250 The directory was successfully removed Related commands delete rstatus Use rstatus to display FTP server status. Use rstatus remotefile to display detailed information about a specific directory or file on the FTP server. Syntax rstatus [ remotefile ] Views FTP client view Predefined user roles network-admin Parameters remotefile: Specifies a directory or file on the FTP server. Usage guidelines You can perform this operation only after you log in to the FTP server.
Filed Description Session timeout in seconds is 300 Timeout interval is 300 seconds. Control connection is plain text Control connection type is plain text. Data connections will be plain text Data connection type is plain text. At session startup, client count was 1 FTP connection number is 1. vsFTPd 2.0.6 - secure, fast, stable FTP version is 2.0.6. 211 End of status End of the display of FTP server status. # Display file a.txt. ftp> rstatus a.
status Use status to display FTP status. Syntax status Views FTP client view Predefined user roles network-admin Examples # Display FTP status. ftp> status Connected to 192.168.1.56. No proxy connection. Not using any security mechanism.
Views FTP client view Predefined user roles network-admin Usage guidelines You can perform this operation only after you log in to the FTP server. Examples # Display the system information of the FTP server. ftp> system 215 UNIX Type: L8 user Use user to change to another user account after login. Syntax user username [ password ] Views FTP client view Predefined user roles network-admin Parameters username: Specifies the username of the target user account.
verbose Use verbose to enable or disable the device to display detailed information about FTP operations. Syntax verbose Default The device displays detailed information about FTP operations. Views FTP client view Predefined user roles network-admin Usage guidelines This command takes effect only the current logged-in users. When the users log in again, the command restores to the default setting. Examples # Disable the device from displaying detailed information about FTP operations.
Parameters command-name: Specifies a command supported by the FTP client. Usage guidelines In FTP client view, entering ? is the same as executing the help command. Examples # Display all commands supported by the FTP client. ftp> ? Commands may be abbreviated.
TFTP commands tftp Use tftp to download a file from the TFTP server to the local device or upload a local file to the TFTP server in an IPv4 network. Syntax tftp tftp-server { get | put | sget } source-filename [ destination-filename ] [ vpn-instance vpn-instance-name ] [ dscp dscp-value | source { interface interface-type interface-number | ip source-ip-address } ] * Views User view Predefined user roles network-admin Parameters tftp-server: Specifies the IPv4 address or host name of a TFTP server.
packets. Make sure the interface is up and has the primary IPv4 address configured. Otherwise, the transmission fails. ip source-ip-address: Specifies an IPv4 address. This address must be the IPv4 address of an interface in up state. Otherwise, the transmission fails. • Usages guidelines The source address specified with the tftp command takes precedence over the source address specified with the tftp client source command.
Default No source IPv4 address is configured for outgoing TFTP packets. The device uses the primary IPv4 address of the output interface for the route to the server as the source IP address. Views System view Predefined user roles network-admin Parameters interface interface-type interface-number: Specifies the source interface for establishing TFTP connections. The primary IPv4 address of the source interface is used as the source IPv4 address for packets sent to a TFTP server.
Parameters tftp-server: Specifies the IPv6 address or host name of a TFTP server. The host name can be a case-insensitive string of 1 to 253 characters and can contain only letters, digits, hyphens (-), underscores (_), and dots (.). -i interface-type interface-number: Specifies an output interface by its type and number. This parameter can be used only when the TFTP server address is a link local address and the specified output interface has a link local address.
Usages guidelines The source address specified with the tftp ipv6 command takes precedence over the source address specified with the tftp client ipv6 source command. The source address specified with the tftp client ipv6 source command applies to all TFTP connections. The source address specified with the tftp ipv6 command applies only to the current TFTP connection. Examples # Download the new.bin file from the TFTP server at 2001::1 and save it as new.bin. tftp ipv6 2001::1 get new.bin new.
Examples # Specify source IPv6 address 2000::1 for outgoing TFTP packets. system–view [Sysname] tftp client ipv6 source ipv6 2000::1 Related commands tftp ipv6 tftp-server acl Use tftp-server acl to use an ACL to control the device's access to TFTP servers in an IPv4 network. Use undo tftp-server acl to restore the default. Syntax tftp-server acl acl-number undo tftp-server acl Default No ACL is used to control the device's access to TFTP servers.
Default No ACL is used to control the device's access to TFTP servers. Views System view Predefined user roles network-admin Parameters acl-number: Specifies the number of a basic ACL, in the range of 2000 to 2999. Usages guidelines You can use an ACL to deny or permit the device's access to specific TFTP servers. Examples # Allow the device to access only the TFTP server at 2001::1.
File system management commands IMPORTANT: • Before managing storage media, files, and directories, make sure you know the possible impacts. • A file or directory whose name starts with a period (.) is considered a hidden file or directory. Do not give a common file or directory a name that starts with a period. • Some system files and directories are hidden. A file name must be specified in one of the file name formats allowed. For more information, see Fundamentals Configuration Guide.
Views User view Predefined user roles network-admin Parameters fileurl-source: Specifies the name or URL of the file to be copied. If the file resides on an FTP or TFTP server rather than on the device, specify the URL of the file. Whether a URL is case sensitive depends on the server. fileurl-dest: Specifies the name or URL of the destination file or directory. To copy the source file to an FTP or TFTP server, specify a URL.
# Copy the 1.cfg file from the Flash's test folder to the USB disk and save it to the testbackup folder on the first partition with the file name 1backup.cfg. copy flash:/test/1.cfg usb0:/testbackup/1backup.cfg Copy flash:/test/1.cfg to usb0:/testbackup/1backup.cfg?[Y/N]:y Copying file flash:/test/1.cfg to usb0:/testbackup/1backup.cfg...Done. # Copy test.cfg from the working directory on FTP server 1.1.1.1 and save it to the local current folder as testbackup.cfg.
delete Use delete to delete a file. Syntax delete [ /unreserved ] file-url Views User view Predefined user roles network-admin Parameters /unreserved: Permanently deletes the specified file. If you do not specify this keyword, the command moves the file to the recycle bin. file-url: Specifies the name of the file to be deleted. Asterisks (*) are acceptable as wildcards. For example, to remove files with the .txt extension in the current directory, enter delete *.txt.
dir Use dir to display files or folders. Syntax dir [ /all ] [ file-url | /all-filesystems ] Views User view Predefined user roles network-admin Parameters /all: Displays all files and folders in the current directory, visible or hidden. If you do not specify this option, only visible files and folders are displayed. file-url: Displays a specific file or folder. The file-url argument can use the asterisk (*) as a wildcard. For example, to display files with the .
Field Description File or folder information: • 0—File or folder number, which is automatically allocated by the system. • -rwh—Attributes of the file or folder. The first character is the folder indicator (d for folder and – for file). The second character indicates whether the file or folder is readable (r for readable). The third character indicates whether the file or directory is writable (w for writable).
Usb: will be divided into the following partitions: DeviceName Capacity usb0: 85MB usb1: 85MB usb2: 86MB All data on usb: will be lost, continue? [Y/N]:y Partitioning usb:...Done. # Divide the USB disk on the device into one partition in an interactive way. fdisk usb: The capacity of usb: : 256M bytes Partition 1 (32MB~224MB, 256MB. Press CTRL+C to quit or Enter to use all available space): // Press Enter or enter 256.
file prompt Use file prompt to set the operation mode for files and folders. Syntax file prompt { alert | quiet } undo file prompt Default The alert mode is activated and the system prompts for confirmation when you perform a destructive file or folder operation. Views System view Predefined user roles network-admin Parameters alert: Prompts for confirmation when a destructive file or folder operation is being performed. quiet: Gives no confirmation prompt for file or folder operations.
Examples # Restore the space of the Flash. fixdisk flash: Restoring flash: may take some time... Restoring flash:...Done. format Use format to format a storage medium. Syntax format medium-name Views User view Predefined user roles network-admin Parameters medium-name: Specifies the name of a storage medium. Usage guidelines Formatting a storage medium permanently deletes all files on the storage medium. If a startup configuration file exists on the storage medium, back it up if necessary.
Predefined user roles network-admin Parameters filename: Specifies the name of the file to be decompressed. This argument must have .gz as the extension. Usage guidelines This command deletes the specified file after decompressing it. Examples # Decompress the file system.bin.gz. 1. Before decompressing the file, you can display files whose names start with the system. string. dir system.* Directory of flash: 1 -rw- 20 Jun 14 2012 10:18:53 system.bin.gz 472972 KB total (472840 KB free) 2.
1 -rw- 0 May 30 2012 11:42:24 system.bin 472972 KB total (472844 KB free) 2. Compress the file system.bin. gzip system.bin 3. Verify the compress operation. dir system.* Directory of flash: 1 -rw- 20 Jun 14 2012 10:18:53 system.bin.gz 472972 KB total (472840 KB free) mkdir Use mkdir to create a folder in the current directory. Syntax mkdir directory Views User view Predefined user roles network-admin Parameters directory: Specifies the name of a folder.
Parameters file-url: Specifies a file name. Examples # Display the contents of the test.txt file. more test.txt Have a nice day. # Display the contents of the testcfg.cfg file. more testcfg.cfg # version 7.1.046, ESS 2405 # sysname Sysname # vlan 2 # return mount Use mount to mount a hot swappable storage medium.
move Use move to move a file. Syntax move fileurl-source fileurl-dest Views User view Predefined user roles network-admin Parameters fileurl-source: Specifies the name of the source file. fileurl-dest: Specifies the name of the destination file or folder. Usage guidelines If you specify a destination folder, the system moves the source file to the specified folder without changing the file name. Examples # Move the flash:/test/sample.txt file to flash:/, and save it as 1.txt.
rename Use rename to rename a file or folder. Syntax rename fileurl-source fileurl-dest Views User view Predefined user roles network-admin Parameters fileurl-source: Specifies the name of the source file or folder. fileurl-dest: Specifies the name of the destination file or folder. Usage guidelines If the destination file or folder name is the same as the name of an existing file or folder in the current working directory, this command is not executed. Examples # Rename the copy.cfg file as test.cfg.
Clear flash:/b.cfg?[Y/N]:y Clearing file flash:/b.cfg... Done. # Delete the b.cfg file from the recycle bin. (In this example there are two files in the recycle bin.) reset recycle-bin Clear flash:/a.cfg?[Y/N]:n Clear flash:/b.cfg?[Y/N]:y Clearing file flash:/b.cfg... Done. Related commands delete rmdir Use rmdir to remove a folder. Syntax rmdir directory Views User view Predefined user roles network-admin Parameters directory: Specifies a folder name.
Parameters file-url: Specifies the name of a file. Usage guidelines The digest can be used to verify the integrity of the file. For example, you can use this command to calculate the digest of a software image file and compare it with that provided on the HP website to verify whether the file has been tampered with. Examples # Use the SHA-256 algorithm to calculate the digest of file system.bin. sha256sum system.
undelete Use undelete to restore a file from the recycle bin. Syntax undelete file-url Views User view Predefined user roles network-admin Parameters file-url: Specifies the name of the file to be restored. Usage guidelines If another file that has the same name exists in the directory, the system prompts you about whether to overwrite the existing file. If you enter Y, the existing file is overwritten. If you enter N, the command is not executed. Examples # Restore the copy.
Configuration file management commands archive configuration Use archive configuration to manually archive the running configuration to the configuration archive directory. Syntax archive configuration Views User view Predefined user roles network-admin Usage guidelines Before manually archiving the running configuration, you must use the archive configuration location command to specify a directory as the configuration archive directory and specify an archive name prefix.
Syntax archive configuration interval minutes undo archive configuration interval Default The system does not automatically archive the running configuration. Views System view Predefined user roles network-admin Parameters minutes: Specifies the interval (in minutes) for automatically saving the running configuration. The value range is 10 to 525600 (365 days).
archive configuration location Use archive configuration location to configure the directory and file name prefix for archiving the running configuration. Use undo archive configuration location to restore the default. Syntax archive configuration location directory filename-prefix filename-prefix undo archive configuration location Default No configuration archive directory or configuration archive file name prefix has been set.
Related commands • archive configuration • archive configuration location • archive configuration max • display archive configuration archive configuration max Use archive configuration max to set the maximum number of configuration archives. Use undo archive configuration max to restore the default. Syntax archive configuration max file-number undo archive configuration max Default Up to five configuration archives can be saved.
• archive configuration interval • display archive configuration backup startup-configuration Use backup startup-configuration to back up the main next-startup configuration file to a TFTP server. Syntax backup startup-configuration to tftp-server [ dest-filename ] Views User view Predefined user roles network-admin Parameters tftp-server: Specifies a TFTP server by its IPv4 address or host name. The host name is a case-insensitive string of 1 to 253 characters.
Parameters private-key: Encrypts configuration with a private key. Any HP device running Comware V7 software can decrypt the encrypted configuration file. public-key: Encrypts configuration with a public key. Any HP device can decrypt the encrypted configuration file. Usage guidelines Configuration encryption enables the device to automatically encrypt a configuration file when saving the running configuration to the file. Examples # Enable the public-key method for configuration encryption.
display archive configuration Use display archive configuration to display configuration archive information, including the archive directory, archive prefix, archive interval, maximum number of archives, and saved archives. Syntax display archive configuration Views Any view Predefined user roles network-admin network-operator Examples # Display configuration archive information.
archive configuration max • display current-configuration Use display current-configuration to display the running configuration. Syntax display current-configuration [ configuration [ module-name ] | interface [ interface-type [ interface-number ] ] ] Views Any view Predefined user roles network-admin network-operator Parameters configuration [ module-name ]: Displays feature configuration. The module-name argument specifies a feature module.
interface FortyGigE1/0/1 port link-mode route # return display default-configuration Use display default-configuration to display the factory defaults. Syntax display default-configuration Views Any view Predefined user roles network-admin network-operator Usage guidelines Factory defaults are contained in the default configuration file. They are product-specific default settings that are different from initial settings.
Examples # Display the main next-startup configuration file. display saved-configuration # version 7.1.046, ESS 2405 # sysname Sysname # ftp server enable # telnet server enable # domain default enable system # vlan 1 # domain system # ---- More ---- Related commands • reset saved-configuration • save display startup Use display startup to display the current startup configuration file and the next-startup configuration files.
Table 19 Command output Field Description MainBoard Displays the startup configuration files on the master device. Current Startup saved-configuration file Configuration file that the device has started up with. Next main startup saved-configuration file Primary startup configuration file to be used at the next startup. Next backup startup saved-configuration file Backup startup configuration file to be used at the next startup.
# line aux 0 user-role network-operator # line con 0 user-role network-admin # line vty 0 64 authentication-mode none user-role network-admin # return reset saved-configuration Use reset saved-configuration to delete next-startup configuration files. Syntax reset saved-configuration [ backup | main ] Views User view Predefined user roles network-admin Parameters backup: Deletes the backup next-startup configuration file. main: Deletes the main next-startup configuration file.
MainBoard: Configuration file is cleared. Related commands display saved-configuration restore startup-configuration Use restore startup-configuration to download a configuration file from a TFTP server and specify it as the main next-startup configuration file. Syntax restore startup-configuration from tftp-server src-filename Views User view Predefined user roles network-admin Parameters tftp-server: Specifies a TFTP server's IPv4 address or host name.
save [ safely ] [ backup | main ] [ force ] Views Any view Predefined user roles network-admin Parameters file-url: Saves the running configuration to the specified file, without specifying the file as a next-startup configuration file. The file name must use the extension .cfg and can include path information. If the file path includes a folder name, the folder must already exist. all: Saves the running configuration to the device. slot slot-number: Saves the running configuration to the device.
Now saving current configuration to the device. Saving configuration flash:/backup.cfg. Please wait... Configuration is saved to flash successfully. # Save the running configuration to the main next-startup configuration file without any confirmation required. save force Validating file. Please wait.... Configuration is saved to device successfully.
Usage guidelines If neither backup nor main is specified, the startup saved-configuration command specifies the main next-startup configuration file. Even though the main and backup next-startup configuration files can be the same one, specify them as separate files for high availability. The undo startup saved-configuration command changes the file attribute of the main and backup next-startup configuration files to NULL, but it does not delete the two configuration files.
Software upgrade commands boot-loader file Use boot-loader file to specify startup software image files. Syntax boot-loader file boot boot-package system system-package [ feature feature-package&<1-30> ] slot slot-number { backup | main } boot-loader file ipe-filename slot slot-number { backup | main } Views User view Predefined user roles network-admin Parameters boot boot-package: Specifies a .bin boot image file, a case-insensitive string of 1 to 63 characters.
Examples # Specify flash:/all.ipe as the backup startup image file. boot-loader file flash:/all.ipe slot 1 backup Verifying image file...........................Done. Images in IPE: boot.bin system.bin This command will set the backup startup software images. Continue? [Y/N]:Y Add images to target slot. flash:/boot.bin already exists on slot 1. flash:/system.bin already exists on slot 1. Overwrite it? [Y/N]:y Decompressing file boot.bin to flash:/boot.bin........................Done.
This command will update the Boot ROM file on the specified board(s), Continue? [Y/N]:y Now updating the Boot ROM, please wait... .............Done. Related commands boot-loader file display boot-loader Use display boot-loader to display current software images and startup software images. Syntax display boot-loader [ slot slot-number ] Views Any view Predefined user roles network-admin network-operator Parameters slot slot-number: Specifies the device ID, which is fixed at 1.
display install active Use display install active to display active software images. Syntax display install active [ slot slot-number ] [ verbose ] Views Any view Predefined user roles network-admin network-operator Parameters slot slot-number: Specifies the device ID, which is fixed at 1. verbose: Displays detailed information about active software images. If you do not specify this keyword, the command displays only the names of the active software images.
Component: system Description: system package Table 21 Command output Field Description Active packages on slot 1 Active software images on the device. The device ID is fixed at 1. [Package] Detailed information about the software image. Image type: Service name • • • • boot—Boot image. system—System image. patch—Patch image. Any other value indicates a feature image. Supported board Types of cards supported by the software image.
flash:/system-a0201.bin # Display detailed information about the main startup software images. display install committed verbose Committed packages on slot 1: flash:/boot-a0201.bin [Package] Vendor: H3C Product: xxxx Service name: boot Platform version: 7.1 Product version: Beta 1330 Supported board: mpu [Component] Component: boot Description: boot package flash:/system-a0201.bin [Package] Vendor: H3C Product: xxxx Service name: system Platform version: 7.
verbose: Displays detailed information about inactive software images. If you do not specify this keyword, the command displays only image names. Usage guidelines This command displays all software image files that have not been activated in the root directory of the storage medium. Examples # Display brief information about inactive software images in the root directory of the storage medium. display install inactive Inactive packages on slot 1: flash:/patch.
Supported board: mpu # Display detailed information about system.bin. display install package flash:/system.bin verbose flash:/system.bin [Package] Vendor: H3C Product: xxxx Service name: system Platform version: 7.1.046 Product version: Beta 1330 Supported board: mpu [Component] Component: system Description: system package For more information about the fields in the command output, see Table 21. install activate Use install activate to install and activate software images.
install commit Use install commit to commit software changes. Syntax install commit Views User view Predefined user roles network-admin Usage guidelines The install activate or install activate command adds or removes patch images to or from the current software image list. For the patch images to run at the next startup, use the install commit command to commit the software change. The commit action adds the patch images to the startup software image list. Examples # Commit software changes.
Examples # Deactivate the patch image file route-patch.bin. install deactivate patch flash:/route-patch.bin slot 1 Related commands • display install active • display install inactive install remove Use install remove to delete inactive software images from the root directory of the storage medium. Syntax install remove [ slot slot-number ] { filename | inactive } Views User view Predefined user roles network-admin Parameters slot slot-number: Specifies the device ID, which is fixed at 1.
Device management commands clock datetime Use clock datetime to set the UTC time. Syntax clock datetime time date Default The UTC time is the factory-default time. Views User view Predefined user roles network-admin Parameters time: Specifies a time in the format hh:mm:ss. The hh value is in the range of 0 to 23, the mm value is in the range of 0 to 59, and the ss value is in the range of 0 to 59. The leading zero in a segment can be omitted. If the seconds segment is 0 (hh:mm:00), you can omit it.
clock protocol Use clock protocol to specify the system time source. Use undo clock protocol to restore the default. Syntax clock protocol { none | ntp } undo clock protocol Default The device uses the NTP time source. Views System view Predefined user roles network-admin Parameters none: Uses the local system time configured by using the clock datetime, clock timezone, and clock summer-time commands. ntp: Uses the NTP time source.
Parameters name: Specifies a name for the daylight saving time schedule, a case-sensitive string of 1 to 32 characters. start-time: Specifies the start time in the format hh:mm:ss. The hh value is in the range of 0 to 23, the mm value is in the range of 0 to 59, and the ss value is in the range of 0 to 59. The leading zero in a segment can be omitted. If the seconds segment is 0 (hh:mm:00), you can omit it. If both the minutes and seconds segments are 0 (hh:00:00), you can omit both of the segments.
system-view [Sysname] clock summer-time PDT 6 08/01 6 09/01 1 Related commands • clock datetime • clock protocol • clock timezone • display clock clock timezone Use clock timezone to set the local time zone. Use undo clock timezone to restore the default. Syntax clock timezone zone-name { add | minus } zone-offset undo clock timezone Default The local time zone is the UTC time zone.
Related commands • clock datetime • clock protocol • clock summer-time • display clock command Use command to assign a command to a job. Use undo command to revoke a command. Syntax command id command undo command id Default No command is assigned to a job. Views Job view Predefined user roles network-admin Parameters id: Specifies a command ID in the range of 0 to 4294967295. command: Specifies the command to be assigned to the job. Usage guidelines A job can have multiple commands.
copyright-info enable Use copyright-info enable to enable displaying the copyright statement. Use undo copyright-info enable to disable displaying the copyright statement. Syntax copyright-info enable undo copyright-info enable Default The copyright statement is displayed. Views System view Predefined user roles network-admin Examples # Enable displaying the copyright statement.
User interface aux0 is available. Press ENTER to get started. display clock Use display clock to display the system time, date, local time zone, and daylight saving time. Syntax display clock Views Any view Predefined user roles network-admin network-operator Examples # Display the system time and date when the local time zone is not specified. display clock 10:09:00 UTC Fri 03/16/2012 # Display the system time and date when the local time zone Z5 is specified.
Predefined user roles network-admin network-operator Examples # Display the copyright statement. display copyright ... display cpu-usage Use display cpu-usage to display CPU usage statistics. Syntax display cpu-usage [ slot slot-number [ cpu cpu-number ] ] Views Any view Predefined user roles network-admin network-operator Parameters slot slot-number: Specifies the device. The slot number must be 1. cpu cpu-number: Displays the CPU usage statistics for the specified CPU.
display cpu-usage configuration Use display cpu-usage configuration to display CPU usage monitoring settings. Syntax display cpu-usage configuration [ slot slot-number [ cpu cpu-number ] ] Views Any view Predefined user roles network-admin Parameters slot slot-number: Specifies the device. The slot number must be 1. cpu cpu-number: Displays the CPU usage monitoring settings for the specified CPU. The cpu number must be 0. Examples # Display the CPU usage monitoring settings.
• The vertical axis represents the CPU usage. If a statistic is not a multiple of the usage step, it is rounded up or down to the closest multiple of the usage step, whichever is closer. For example, if the CPU usage step is 5%, the statistic 53% is rounded up to 55%, and the statistic 52% is rounded down to 50%. • The horizontal axis represents the time. • Consecutive pound signs (#) indicate the CPU usage at a specific time.
100%| 95%| 90%| 85%| 80%| 75%| 70%| 65%| 60%| 55%| 50%| 45%| 40%| 35%| 30%| 25%| 20%| 15%| 10%| 5%| # -----------------------------------------------------------10 20 30 40 50 60 (minutes) cpu-usage (CPU 0) last 60 minutes (scmd) The output shows the historical CPU usage statistics of process 1 (with the process name scmd) in the last 60 minutes. A process name with square brackets ([ ]) means that the process is a kernel process.
Examples # Display device information. display device Slot 1 SubSNo PortNum PCBVer FPGAVer CPLDVer BootRomVer AddrLM Type State 0 NULL 001 001 202 Normal 35 Ver.A IVL MAIN Table 23 Command output Field Description Slot 1 Hardware information about the switch. The slot number is always 1. SubSNo Subslot number of the subcard. The switch does not support subcards. PortNum Maximum number of ports that the switch supports. PCBVer PCB version of the switch.
DEVICE_NAME : HP FlexFabric 5930-32QSFP+ Switch JG726A DEVICE_SERIAL_NUMBER : 210235A1AE0000001234 MAC_ADDRESS : 00E0-FC00-5800 MANUFACTURING_DATE : 2008-05-08 VENDOR_NAME : HP Fan 1 DEVICE_NAME Fan Tray JG552A : HP X711 Front (port side) to Back (power side) Airflow High Volume DEVICE_SERIAL_NUMBER : 210231A0WFH115000073 MANUFACTURING_DATE : 2011-11-12 VENDOR_NAME : HP Fan 2 DEVICE_NAME Fan Tray JG552A : HP X711 Front (port side) to Back (power side) Airflow High Volume DEVICE_SERIAL_NUMBER
Parameters slot slot-number: Specifies the device. The slot number must be 1. fan-id: Specifies a fan by its ID in the range of 1 to 2. Examples # Display the electronic label information of fan 2.
Views Any view Predefined user roles network-admin network-operator Parameters hardware: Displays hardware-related operating statistics. infrastructure: Displays operating statistics for the fundamental modules. l2: Displays operating statistics for the Layer 2 features. l3: Displays operating statistics for the Layer 3 features. service: Displays operating statistics for upper-layer features.
Parameters slot slot-number: Specifies the device. The slot number must be 1. Examples # Display the temperature statistics for all temperature sensors on the device.
fan-id: Specifies a fan by its ID in the range of 1 to 2. Examples # Display the operating states of all fans. display fan Slot 1 FAN 1 State : Normal Wind Direction :Port-to-Power Prefer Wind Direction FAN :Port-to-Power 2 State : Normal Wind Direction :Port-to-Power Prefer Wind Direction :Port-to-Power display memory Use display memory to display memory usage.
Field Description Total size of the physical memory space that can be allocated. Total The memory space is virtually divided into two parts. Part 1 is solely used for kernel codes, and kernel management. Part 2 can be allocated and used for such tasks as running service modules and storing files. The size of part 2 equals the total size minus the size of part 1. Used Used physical memory. Free Free physical memory. Shared Physical memory shared by processes.
Current memory state: Normal Event statistics: [Back to normal state] First notification: 0.0 Latest notification: 0.0 Total number of notifications sent: 0 [Enter minor low-memory state] First notification at: 0.0 Latest notification at: 0.0 Total number of notifications sent: 0 [Back to minor low-memory state] First notification at: 0.0 Latest notification at: 0.0 Total number of notifications sent: 0 [Enter severe low-memory state] First notification at: 0.0 Latest notification at: 0.
Input Power : 182(W) Power 1 State : Absent Power 2 State : Normal Type : AC display scheduler job Use display scheduler job to display job configuration information. Syntax display scheduler job [ job-name ] Views Any view Predefined user roles network-admin network-operator Parameters job-name: Specifies a job by its name, a case-sensitive string of 1 to 47 characters. Without this option, the command displays the configuration information of all jobs.
network-operator Examples # Display job execution log information. display scheduler logfile Logfile Size: 1902 Bytes. Job name : shutdown Schedule name : shutdown Execution time : Tue Dec 27 10:44:42 2011 Completion time : Tue Dec 27 10:44:47 2011 --------------------------------- Job output ----------------------------------system-view System View: return to User View with Ctrl+Z.
Related commands • scheduler reboot at • scheduler reboot delay display scheduler schedule Use display scheduler schedule to display schedule information. Syntax display scheduler schedule [ schedule-name ] Views Any view Predefined user roles network-admin network-operator Parameters schedule-name: Specifies a schedule by its name, a case-sensitive string of 1 to 47 characters. Without this option, the command displays information about all schedules.
Field Description Job name Name of a job under the schedule. Result of the most recent execution: Last execution status • • • • • Successful. Failed. Waiting—The device is executing the schedule and the job is waiting to be executed. In process—The job is being executed. -NA-—The execution time has not arrived yet. To view information about whether the commands in the job has been executed and the execution results, execute the display scheduler logfile command.
Usage guidelines Table 29 shows the common transceiver alarms. If no error occurs, "None" is displayed. Table 29 Common transceiver alarms Field Description QSFP+: RX signal loss in channel x Signal loss occurred in the inbound direction of the specified channel. TX fault in channel x Transmission error occurred in the specified channel. TX signal loss in channel x Transmitted signals were lost in the specified channel.
Parameters interface [ interface-type interface-number ]: Specifies an interface by its type and number. If no interface is specified, this command displays the current values of the digital diagnosis parameters on every transceiver module. Usage guidelines This command cannot display information about some transceiver modules. Examples # Display the current values of the digital diagnosis parameters on the transceiver module in interface FortyGigE1/0/2.
Examples # Display the key parameters of the transceiver module in interface FortyGigE 1/0/3. display transceiver interface fortygige 1/0/3 FortyGigE1/0/3 transceiver information: Transceiver Type : 40G_BASE_LR4_QSFP_PLUS Connector Type : LC Wavelength(nm) : 1301 Transfer Distance(m) : 10(SMF) Digital Diagnostic Monitoring : YES Vendor Name : HP Ordering Name : JG661A Table 31 Command output Field Description transceiver information Transceiver information.
Views Any view Predefined user roles network-admin network-operator Parameters interface [ interface-type interface-number ]: Specifies an interface by its type and number. If no interface is specified, this command displays the electronic label information of the transceiver modules on all interfaces. Usage guidelines This command displays only part of the electronic label information. Examples # Display the electronic label information of the transceiver module in interface FortyGigE1/0/4.
display version-update-record Use display version-update-record to display the startup software image upgrade history records. Syntax display version-update-record Views Any view Predefined user roles network-admin network-operator Usage guidelines The device records its current startup software version information and all subsequent version update information. Such information can survive reboots. The maximum number of records is 10.
Predefined user roles network-admin Parameters slot slot-number: Specifies the device. The slot number must be 1. power-to-port: Specifies the airflow direction from the power supply side to the port side. port-to-power: Specifies the airflow direction from the port side to the power supply side. Examples # Set the preferred airflow direction to port-to-power. system-view [Sysname] fan prefer-direction slot 1 port-to-power Related commands display fan header Use header to create a banner.
system-view [Sysname] header incoming Please input banner content, and quit with the character '%'. Welcome to incoming(header incoming)% [Sysname] header legal Please input banner content, and quit with the character '%'. Welcome to legal (header legal)% [Sysname] header login Please input banner content, and quit with the character '%'. Welcome to login(header login)% [Sysname] header motd Please input banner content, and quit with the character '%'.
Syntax job job-name undo job job-name Default No job is assigned to a schedule. Views Schedule view Predefined user roles network-admin Parameters job-name: Specifies the job name, a case-sensitive string of 1 to 47 characters. Usage guidelines You can assign multiple jobs to a schedule. The jobs in a schedule are executed concurrently. The jobs to be assigned to a schedule must already exist. To create a job, use the scheduler job command. Examples # Assign job save-job to schedule saveconfig.
Predefined user roles network-admin Parameters minor minor-value: Specifies the minor alarm threshold in the range of 0 to 2726. This threshold must be equal to or less than the total memory size. Setting this threshold to 0 disables the minor alarm function. severe severe-value: Specifies the severe alarm threshold in the range of 0 to 2726. This threshold must be equal to or less than the minor alarm threshold. Setting this threshold to 0 disables the severe alarm function.
Examples # Enable CPU usage recording. system-view [Sysname] monitor cpu-usage enable monitor cpu-usage interval Use monitor cpu-usage interval to set the CPU usage sampling interval. Syntax monitor cpu-usage interval interval-value [ slot slot-number] Default The CPU usage sampling interval is 1 minute. Views System view Predefined user roles network-admin Parameters interval-value: Specifies the CPU usage sampling interval.
Usage guidelines Password recovery capability controls console user access to the device configuration and SDRAM from Boot ROM menus. If password recovery capability is enabled, a console user can access the device configuration without authentication to configure new passwords. If password recovery capability is disabled, console users must restore the factory-default configuration before they can configure new passwords.
reboot Start to check configuration with next startup configuration file, please wait.........DONE! This command will reboot the device. Continue? [Y/N]:y Now rebooting, please wait... # If any configuration has changed, reboot the device and save the configuration. reboot Start to check configuration with next startup configuration file, please wait.........DONE! Current configuration will be lost after the reboot, save current configuration? [Y/N]:y Please input the file name(*.
Related commands display scheduler logfile reset version-update-record Use reset version-update-record to clear the startup software image upgrade history records. Syntax reset version-update-record Views System view Predefined user roles network-admin Examples # Clear the startup software image upgrade history records.
Examples # Restore the factory-default settings and states for the device. restore factory-default This command will restore the system to the factory default configuration and clear the operation data. Continue [Y/N]:y Restoring the factory default configuration. This process might take a few minutes. Please wait................................................................................. .........................Done.
Syntax scheduler logfile size value Default The size of the job execution log file is 16 KB. Views System view Predefined user roles network-admin Parameters value: Sets the size of the job execution log file, in KB. The value range is 16 to 1024. Usage guidelines The job execution log file saves the execution information of jobs. If the file is full, old records will be replaced by new records.
Usage guidelines CAUTION: Device reboot interrupts network services. When the date argument is not specified: • If the reboot time is later than the current time, a reboot occurs at the reboot time of the current day. • If the reboot time is earlier than the current time, a reboot occurs at the reboot time the next day. For data security, if you are performing file operations at the reboot time, the system does not reboot. The device supports only one device reboot schedule.
The device supports only one device reboot schedule. If you configure both the schedule reboot delay and schedule reboot delay commands or configure one of the commands multiple times, the most recent configuration takes effect. Examples # Configure the device to reboot after 88 minutes. This example assumes that the current time is 11:48 a.m. on June 6, 2011. scheduler reboot delay 88 Reboot system at 13:16 06/06/2011(in 1 hours and 28 minutes).
Related commands • job • time at • time once • time interval shutdown-interval Use shutdown-interval to set the detection timer. Use undo shutdown-interval to restore the default. Syntax shutdown-interval time undo shutdown-interval Default The detection interval is 30 seconds. Views System view Predefined user roles network-admin Parameters time: Specifies a detection timer (in seconds) in the range of 1 to 300.
Syntax switch-mode { 0 | 1 | 2 | 3 | 4 } undo switch-mode Default The device operates in mode 0: • 288 KB MAC address table. • 16 KB ARP table or 8 KB ND table. • 16 KB IPv4 routing table or 8 KB IPv6 routing table. Views System view Predefined user roles network-admin Parameters 0: Operates in mode 0. 1: Operates in mode 1. 2: Operates in mode 2. 3: Operates in mode 3. 4: Operates in mode 4.
Syntax sysname sysname undo sysname Default The default device name is HP. Views System view Predefined user roles network-admin Parameters sysname: Specifies a name for the device, a string of 1 to 64 characters. Usage guidelines A device name identifies a device in a network and is used as the user view prompt at the CLI. For example, if the device name is Sysname, the user view prompt is . Examples # Set the name of the device to R2000.
Examples # Set the operating mode to advanced. system-view [Sysname] system-working-mode advance The system working mode is changed, it will take effect after system restart. temperature-limit Use temperature-limit to set the temperature alarm thresholds for the device. Use undo temperature-limit to restore the default.
warninglimit: Specifies a warning temperature threshold in Celsius degrees, where warninglimit is in the range of 40°C to 99°C (104°F to 210.2°F). This threshold must be greater than the lower temperature threshold. alarmlimit: Specifies an alarming temperature threshold in Celsius degrees, where alarmlimit is in the range of 41°C to 100°C (105.8°F to 212°F). This threshold must be greater than the warning temperature threshold.
The time at command, the time once command, and the time repeating command overwrite one another. The most recently configured command takes effect. Examples # Configure the device to execute schedule saveconfig at 01:01 a.m. on May 11, 2011. system-view [Sysname] scheduler schedule saveconfig [Sysname-schedule-saveconfig] time at 1:1 2011/05/11 Related commands scheduler schedule time once Use time once to specify one or more execution days and the execution time for a one-time schedule.
Examples # Configure the device to execute schedule saveconfig once at 15:00. system-view [Sysname] scheduler schedule saveconfig [Sysname-schedule-saveconfig] time once at 15:00 Schedule starts at 15:00 5/11/2011. # Configure the device to execute schedule saveconfig once at 15:00 on the coming 15th day in a month.
range for DD depends on the month value. If you do not specify this argument, the execution start date is the first day when the specified time arrives. interval interval-time: Specifies the execution time interval in the format hh:mm or mm. This argument can consist up to 6 characters. When in the format hh:mm, mm must be in the range of 0 to 59. When in the format mm, this argument must be at least 1 minute. month-date [ month-day | last ]: Specifies a day in a month, in the range 1 to 31.
usb disable Use usb disable to disable all USB interfaces. Use undo usb disable to enable all USB interfaces. Syntax usb disable undo usb disable Default All USB interfaces are enabled. Views System view Predefined user roles network-admin Usage guidelines You can use USB interfaces to upload or download files. By default, all USB interfaces are enabled. Before executing this command, use the umount command to unmount all USB partitions.
Support and other resources Contacting HP For worldwide technical support information, see the HP support website: http://www.hp.
Conventions This section describes the conventions used in this documentation set. Command conventions Convention Description Boldface Bold text represents commands and keywords that you enter literally as shown. Italic Italic text represents arguments that you replace with actual values. [] Square brackets enclose syntax choices (keywords or arguments) that are optional. { x | y | ... } Braces enclose a set of required syntax choices separated by vertical bars, from which you select one.
Network topology icons Represents a generic network device, such as a router, switch, or firewall. Represents a routing-capable device, such as a router or Layer 3 switch. Represents a generic switch, such as a Layer 2 or Layer 3 switch, or a router that supports Layer 2 forwarding and other Layer 2 features. Represents an access controller, a unified wired-WLAN module, or the switching engine on a unified wired-WLAN switch. Represents an access point.
Index ABCDEFGHIJLMNOPQRSTUVW debug,81 A delete,82 activation-key,12 delete,117 append,76 description,47 archive configuration,131 dir,82 archive configuration interval,131 dir,118 archive configuration location,133 disconnect,83 archive configuration max,134 display | { begin | exclude | include },2 ascii,77 display | by-linenum,3 authentication-mode,13 display >,4 auto-execute command,14 display >>,4 B display archive configuration,137 backup startup-configuration,135 display boot-l
ftp server acl,73 display line,18 display memory,173 ftp server dscp,73 display memory-threshold,174 ftp server enable,74 display power,175 ftp server ipv6 dscp,74 display role,47 ftp server ssl-server-policy,75 display role feature,49 ftp timeout,76 display role feature-group,52 G display saved-configuration,139 get,88 display scheduler job,176 gunzip,122 display scheduler logfile,176 gzip,123 display scheduler reboot,177 display scheduler schedule,178 H display startup,140 header,185
scheduler reboot at,194 O scheduler reboot delay,195 open,93 scheduler schedule,196 P screen-length,32 parity,31 screen-length disable,10 passive,94 send,33 password-recovery enable,189 set authentication password,34 permit interface,55 sha256sum,128 permit vlan,56 shell,35 permit vpn-instance,58 shutdown-interval,197 protocol inbound,31 speed,36 put,94 startup saved-configuration,145 pwd,126 status,103 pwd,95 stopbits,36 Q Subscription service,206 quit,9 super,64 super authent
umount,129 V undelete,130 verbose,105 usb disable,205 vlan policy deny,67 user,104 vpn-instance policy deny,68 user-interface,43 W user-interface class,44 Websites,206 user-role,46 212
