HP FlexFabric 7900 Switch Series Fundamentals Command Reference Part number: 5998-4289 Software version: Release 2109 Document version: 6W100-20140122
Legal and notice information © Copyright 2014 Hewlett-Packard Development Company, L.P. No part of this documentation may be reproduced or transmitted in any form or by any means without prior written consent of Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice.
Contents Basic CLI commands ···················································································································································· 1 command-alias enable ············································································································································· 1 command-alias mapping ········································································································································· 1 displa
terminal type ·························································································································································· 41 user-interface ·························································································································································· 42 user-interface class ················································································································································ 4
passive ···································································································································································· 87 put ··········································································································································································· 88 pwd ·························································································································································
display this ··························································································································································· 132 reset saved-configuration ···································································································································· 133 restore startup-configuration ······························································································································· 134 save ·········
reset scheduler logfile ········································································································································· 191 reset version-update-record ································································································································ 192 scheduler job ······················································································································································· 192 scheduler logfi
Basic CLI commands command-alias enable Use command-alias enable to enable the command keyword alias function. Use undo command-alias enable to disable the command keyword alias function. Syntax command-alias enable undo command-alias enable Default The command keyword alias function is disabled. Views System view Predefined user roles network-admin Usage guidelines Configured command keyword aliases take effect only when the command keyword alias function is enabled.
Views System view Predefined user roles network-admin Parameters cmdkey: Specifies the first keyword of a non-undo command or the second keyword of an undo command. You must enter the keyword in its complete form. alias: Specifies an alias for the keyword, a string of 1 to 20 characters. It must be different from the first keyword of any non-undo command and the second keyword of any undo command.
include: Displays all lines matching the specified regular expression. regular-expression: Specifies a regular expression, a case-sensitive string of 1 to 256 characters. Usage guidelines Use the | { begin | exclude | include } regular-expression option with a display command to filter the command output. For more information about regular expressions, see Fundamentals Configuration Guide. Examples # Display the lines that contain "vlan" in the running configuration.
9: Untagged ports: 10: FortyGigE1/0/1 # Display the first line that begins with "user-group" in the running configuration and all of the following lines. display current-configuration | by-linenum begin user-group 114: user-group system 115- # 116- return display > Use display > to save the output from a display command to a separate file.
display >> Use display >> to append the output from a display command to the end of a file. Syntax display command >> filename Views Any view Predefined user roles network-admin network-operator Parameters command: Specifies the keywords and arguments of a display command. To display available keywords and arguments, enter display ?. filename: Specifies the name of the file that is used to save the output, a string of 1 to 63 characters.
FortyGigE1/0/1 display command-alias Use display command-alias to display the status of the command keyword alias function and the configured command keyword alias. Syntax display command-alias Views Any view Predefined user roles network-admin network-operator Examples # Display command keyword alias information.
Examples # Display all commands saved in the command history buffer for the current CLI session. display history-command system-view vlan 2 quit Related commands history-command max-size display history-command all Use display history-command all to display all commands saved in the command history buffer for all CLI sessions.
Views Any view Predefined user roles network-admin network-operator Examples # Display hotkey information. display hotkey ----------------- Hotkeys -----------------Defined command hotkeysCTRL_G display current-configuration CTRL_L display ip routing-table CTRL_O undo debugging all -Undefined command hotkeysCTRL_T NULL CTRL_U NULL -System-reserved hotkeysCTRL_A Move the cursor to the beginning of the line. CTRL_B Move the cursor one character to the left. CTRL_C Stop the current command.
hotkey Use hotkey to assign a command to a configurable hotkey. Use undo hotkey to restore the default. Syntax hotkey { CTRL_G | CTRL_L | CTRL_O | CTRL_T | CTRL_U } command undo hotkey { CTRL_G | CTRL_L | CTRL_O | CTRL_T | CTRL_U } Default • Ctrl_G: display current-configuration (display the running configuration). • Ctrl_L: display ip routing-table (display the IPv4 routing table information). • Ctrl_O: undo debugging all (disable all debugging functions).
Syntax quit Views Any view Predefined user roles network-admin network-operator Usage guidelines Executing this command in user view disconnects you from the device. Examples # Return from FortyGigE 1/0/1 interface view to system view and then to user view. [Sysname-FortyGigE1/0/1] quit [Sysname] quit return Use return to return to user view from any other view.
Default The default depends on the configuration of the screen-length command in user line view. The following are default settings for the screen-length command: • Pausing between screens of output. • Displaying up to 24 lines on a screen. Views User view Predefined user roles network-admin Usage guidelines If you disable pausing between screens of output, all output is displayed. The screen is refreshed continuously until the final screen is displayed.
Login management commands The device supports the FIPS mode that complies with NIST FIPS 140-2 requirements. Support for features, commands, and parameters might differ in FIPS mode and non-FIPS mode. For more information about FIPS mode, see Security Configuration Guide. Some login management commands are available in both user line view and user line class view: • A setting in user line view is applied only to the user line. A setting in user line class view is applied to all user lines of the class.
• If the setting in user line view is the default setting but the setting in user line class view is not, the setting in user line class view takes effect. To display the shortcut key you have defined, use the display current-configuration | include activation-key command. Examples # Configure character s as the shortcut key for starting a terminal session on the user line AUX 0. system-view [Sysname] line aux 0 [Sysname-line-aux0] activation-key s To verify the configuration: 1.
Parameters none: Disables authentication. password: Performs local password authentication. scheme: Performs AAA authentication. For more information about AAA, see Security Configuration Guide. Usage guidelines When the authentication mode is none, any user can log in without authentication. To improve device security, use the password or scheme authentication mode. In VTY line view, this command is associated with the protocol inbound command.
Syntax auto-execute command command undo auto-execute command Default Command auto-execution is disabled. Views User line view, user line class view Predefined user roles network-admin Parameters command: Specifies the command to be automatically executed. Usage guidelines This command is not supported in AUX line view or AUX line class view.
Trying 192.168.1.41 ... Press CTRL+K to abort Connected to 192.168.1.41 ... ****************************************************************************** * Copyright (c) 2010-2013 Hewlett-Packard Development Company, L.P. * * Without the owner's prior written consent, * * no decompiling or reverse-engineering shall be allowed. * ****************************************************************************** This operation is the same as directly logging in to the device at 192.168.1.
databits Use databits to specify the number of data bits for each character. Use undo databits to restore the default. Syntax databits { 5 | 6 | 7 | 8 } undo databits Default Eight data bits are used for each character. Views User line view Predefined user roles network-admin Parameters 5: Uses five data bits for each character. 6: Uses six data bits for each character. 7: Uses seven data bits for each character. 8: Uses eight data bits for each character.
Parameters number1: Specifies the absolute number of a user line. The value range is 0 to 64 in standalone mode and 0 to 67 in IRF mode. aux: Specifies the AUX line. vty: Specifies the VTY line. number2: Specifies the relative number of a user line. The value ranges are as follows: • AUX line—0 in standalone mode and 0 to 3 in IRF mode. • VTY line—0 to 63. summary: Displays summary information about user lines. If you do not specify this keyword, the detailed information is displayed.
Table 2 Command output Fields Description number:status The number indicates the absolute number of the first user line of the user line class. The status indicates whether or not the user lines are being used (X for unused and U for used). For example, if "0:X" is displayed, the user line class has one user line. The user line uses the absolute number 0 and is being used.
Parameters number1: Specifies the absolute number of a user line. The value range is 0 to 64 in standalone mode and 0 to 67 in IRF mode. aux: Specifies the AUX line. vty: Specifies the VTY line. number2: Specifies the relative number of a user line. The value ranges are as follows: • AUX line—0 in standalone mode and 0 to 3 in IRF mode. • VTY line—0 to 63. summary: Displays summary information about user lines. If you do not specify this keyword, the detailed information is displayed.
1 lines used. (U) 64 lines not used. (X) Table 4 Command output Fields Description number:status The number indicates the absolute number of the first user line of the user line class. The status indicates whether or not the user lines are being used (X for unused and U for used). For example, if "0:X" is displayed, the user line class has one user line. The user line uses the absolute number 0, and is being used. display users Use display users to display online CLI user information.
Table 5 Command output Field Description Idx Absolute number of the user line. Line Type and relative number of the user line. Idle Time elapsed after the user's most recent input, in the format hh:mm:ss. Time Login time of the user. Pid Process ID of the user session. Type User type, such as Telnet, SSH. + Indicates the user line you are using. Location IP address of the user. escape-key Use escape-key to define a shortcut key for terminating a task.
• If you are managing the local device, pressing the key enters the character as a common character. • If you Telnet to another device and manage the remote device, pressing the key does nothing. You can execute this command multiple times, but only the most recent configuration takes effect. To view the current shortcut key definition, use the display current-configuration command.
Parameters hardware: Performs hardware flow control. none: Disables flow control. software: Performs software flow control. Usage guidelines This command is not supported in VTY line view. The device supports flow control in both the inbound and outbound directions: • For flow control in the inbound direction, the local device listens to flow control information from the remote device. • For flow control in the outbound direction, the local device sends flow control information to the remote device.
Examples # Release user line VTY 1: 1. Display online users. display users Idx Line Idle Time Pid Type 10 VTY 0 00:10:49 Jun 11 11:27:32 320 TEL + 11 VTY 1 00:00:00 Jun 11 11:39:40 334 TEL Following are more details. VTY 0 : Location: 192.168.1.12 VTY 1 : Location: 192.168.1.26 2. + : Current operation user. F : Current operation user works in async mode. If the operations of the user on VTY 1 impact your operations, log out the user.
Examples # Release user line VTY 1: 1. Display online users. display users Idx LINE Idle Time Pid Type 10 VTY 0 00:10:49 Jun 11 11:27:32 320 TEL + 11 VTY 1 00:00:00 Jun 11 11:39:40 334 TEL Following are more details. VTY 0 : Location: 192.168.1.12 VTY 1 : Location: 192.168.1.26 2. + : Current operation user. F : Current operation user works in async mode. If the operations of the user on VTY 1 impact your operations, log out the user.
• If the setting in user line view is not the default setting, the setting in user line view takes effect. • If the setting in user line view is the default setting but the setting in user line class view is not, the setting in user line class view takes effect. Examples # Set the size of the command history buffer to 20 for user line AUX 0. system-view [Sysname] line aux 0 [Sysname-line-aux0] history-command max-size 20 idle-timeout Use idle-timeout to set the session idle timeout.
line Use line to enter one or multiple user line views. Syntax line { first-number1 [ last-number1 ] | { aux | vty } first-number2 [ last-number2 ] } Views System view Predefined user roles network-admin Parameters first-number1: Specifies the absolute number of the first user line. The value range is 0 to 64 in standalone mode and 0 to 67 in IRF mode. last-number1: Specifies the absolute number of the last user line. This number cannot be smaller than first-number1. aux: Specifies the AUX line.
Syntax line class { aux | vty } Views System view Predefined user roles network-admin Parameters aux: Specifies the AUX line class view. vty: Specifies the VTY line class view. Usage guidelines To configure the same settings for all user lines of a line class, use this command to enter the user line class view. Some login management commands are available in both user line view and user line class view: • A setting in user line view is applied only to the user line.
Press ENTER to get started. 3. Press Enter. Pressing Enter does not start a session. 4. Enter s. A terminal session is started. Related commands line lock Use lock to lock the current user line. This method prevents unauthorized users from using the user line. Syntax lock Default By default, the system does not lock any user line. Views User view Predefined user roles network-admin Usage guidelines This command is not supported in FIPS mode.
parity Use parity to specify a parity check mode. Use undo parity to restore the default. Syntax parity { even | mark | none | odd | space } undo parity Default The setting is none, and no parity check is performed. Views User line view Predefined user roles network-admin Parameters even: Performs even parity check. mark: Performs mark parity check. none: Disables parity check. odd: Performs odd parity check. space: Performs space parity check.
protocol inbound ssh undo protocol inbound Default In non-FIPS mode, both protocols are supported. In FIPS mode, SSH is supported. Views VTY line view, VTY line class view Predefined user roles network-admin Parameters all: Supports both protocols. ssh: Supports SSH only. telnet: Supports Telnet only. Usage guidelines This configuration is effective only for a user who logs in through the user line after the configuration is completed.
Syntax screen-length screen-length undo screen-length Default Up to 24 lines are displayed on a screen. Views User line view, user line class view Predefined user roles network-admin Parameters screen-length: Specifies the maximum number of lines to be displayed on a screen, in the range of 0 to 512. Setting this argument to 0 disables pausing between screens of output.
Views User view Predefined user roles network-admin Parameters all: Specifies all user lines. number1: Specifies the absolute number of a user line. The value range is 0 to 64 in standalone mode and 0 to 67 in IRF mode. aux: Specifies the AUX line. vty: Specifies the VTY line. number2: Specifies the relative number of a user line. The value ranges are as follows: • AUX line—0 in standalone mode and 0 to 3 in IRF mode. • VTY line—0 to 63. Usage guidelines To end a message, press Enter.
Views User line view, user line class view Predefined user roles network-admin Parameters hash: Sets a hashed password. simple: Sets a plaintext password. password: Specifies the password string. This argument is case sensitive. If simple is specified, it must be a string of 1 to 16 characters. If hash is specified, it must be a string of 1 to 110 characters. Usage guidelines This command is not supported in FIPS mode.
Predefined user roles network-admin Usage guidelines The undo shell command is not supported in AUX line view or AUX line class view. You cannot disable the terminal service on the user line you are using. When the device operates as a Telnet or SSH server, you cannot configure the undo shell command. If the undo shell command is configured in user line class view, you cannot configure the shell command in the view of a user line in the class.
system-view [Sysname] line aux 0 [Sysname-line-aux0] speed 19200 stopbits Use stopbits to specify the number of stop bits for a character. Use undo stopbits to restore the default. Syntax stopbits { 1 | 1.5 | 2 } undo stopbits Default One stop bit is used. Views User line view Predefined user roles network-admin Parameters 1: Uses one stop bit. 1.5: Uses one and a half stop bits. The device does not support using one and a half stop bits. If you specify this keyword, two stop bits are used.
Predefined user roles network-admin Parameters remote-host: Specifies the IPv4 address or host name of a remote host. A host name can be a case-insensitive string of 1 to 253 characters. Valid characters for a host name include letters, digits, hyphens (-), underscores (_), and dots (.). service-port: Specifies the TCP port number for the Telnet service on the remote host. The value range is 0 to 65535 and the default is 23.
Parameters interface interface-type interface-number: Specifies a source interface. The primary IPv4 address of the interface will be used as the source IPv4 address for outgoing Telnet packets. ip ip-address: Specifies a source IPv4 address. Usage guidelines This command is not supported in FIPS mode. The source IPv4 address or source interface that is specified by this command applies to all Telnet connections.
This command does not take effect on existing Telnet connections. You can specify an ACL that has not been created yet in this command. The command takes effect after the ACL is created. For more information about ACL, see ACL and QoS Configuration Guide. Examples # Permit only the user at 1.1.1.1 to Telnet to the device. system-view [Sysname] acl number 2001 [Sysname-acl-basic-2001] rule permit source 1.1.1.
Syntax telnet server enable undo telnet server enable Default The Telnet server function is disabled. Views System view Predefined user roles network-admin Usage guidelines This command is not supported in FIPS mode. Administrators can Telnet to the device only when the Telnet server function is enabled. Examples # Enable the Telnet server function. system-view [Sysname] telnet server enable terminal type Use terminal type to specify the terminal display type.
Examples # Set the terminal display type to VT100. system-view [Sysname] line vty 0 [Sysname-line-vty0] terminal type vt100 user-interface Use user-interface to enter one or multiple user line views. Syntax user-interface { first-number1 [ last-number1 ] | { aux | vty } first-number2 [ last-number2 ] } Views System view Predefined user roles network-admin Parameters first-number1: Specifies the absolute number of the first user line.
[Sysname] user-interface vty 0 4 [Sysname-line-vty0-4] Related commands user-interface class user-interface class Use user-interface class to enter user line class view. Syntax user-interface class { aux | vty } Views System view Predefined user roles network-admin Parameters aux: Specifies the AUX line class view. vty: Specifies the VTY line class view. Usage guidelines To configure the same settings for all user lines of a line class, use this command to enter the user line class view.
# In AUX 0 line view, restore the default shortcut key for starting a terminal session. [Sysname] user-interface aux 0 [Sysname-line-aux0] undo activation-key Alternatively: [Sysname-line-aux0] activation-key 13 To verify the configuration: 1. Exit the console session. [Sysname-line-aux0] return quit 2. Log in again through the AUX line. The following message appears: Press ENTER to get started. 3. Press Enter. Pressing Enter does not start a session. 4. Enter s.
You can assign up to 64 user roles to a user line. A user logged in through the user line gets all the user roles. For more information about user roles, see "Configuring RBAC." Examples # Assign user role network-admin through the user line VTY 0.
RBAC commands The device supports the FIPS mode that complies with NIST FIPS 140-2 requirements. Support for features, commands, and parameters might differ in FIPS mode and non-FIPS mode. For more information about FIPS mode, see Security Configuration Guide. description Use description to configure a description for a user role. Use undo description to delete the description of a user role. Syntax description text undo description Default A user role has no description.
Predefined user roles network-admin network-operator Parameters name role-name: Specifies a user role name, a case-sensitive string of 1 to 63 characters. Usage guidelines If no user role name is specified, the command displays information about all user roles, including the predefined user roles. Examples # Display information about the user role 123.
Field Description User role rule number. Rule A user role rule specifies the permission to access a command or a set of commands. Predefined user role rules are identified by sys-n, where n represents an integer. Access to the command: Perm • permit—User role has access to the command. • deny—User role has no access to the command. Command type: Type • R—Read-only. • W—Write. • X—Execute. Rule control scope: • command—Controls access to the command or commands, as specified in the Entity field.
Usage guidelines If neither name feature-name nor verbose is specified, the display role feature command displays only the list of features available in the system. Examples # Display the list of feature names. display role feature Feature: device (Device configuration related commands) Feature: interface (Interface related commands) Feature: syslog (Syslog related commands) Feature: process (Process related commands) … # Display the commands of each feature.
system-view ; transceiver * (W) system-view ; system-working-mode * (W) system-view ; archive configuration * (W) system-view ; configuration encrypt * (W) system-view ; version check ignore (W) system-view ; version auto-update enable (W) system-view ; bootrom-update security-check enable system-view ; clock protocol * (W) (W) system-view ; password-recovery * (W) system-view ; switch-fabric removal-signal-suppression system-view ; rtm * (W) system-view ; rtm * ; action * (W) system-vi
super * (X) display password-control * reset password-control * (R) (W) system-view ; password-control * (W) Table 7 Command output (display role feature name aaa) Field Description Feature Displays the name and brief function description of the feature. system-view ; domain * All the commands that start with domain in system view and all the commands in ISP domain view. system-view ; header * All the commands that start with header in system view.
Predefined user roles network-admin network-operator Parameters name feature-group-name: Specifies a feature group. The feature-group-name argument represents the feature group name, a case-sensitive string of 1 to 31 characters. If no feature group is specified, the command displays information about all feature groups. verbose: Displays the commands of each feature in the specified feature group.
Parameters feature-name: Specifies a feature name. You must enter the feature name exactly as it is displayed, including the case. Usage guidelines Repeat the feature command to add multiple features to a feature group. Examples # Add the security features AAA and ACL to the security group security-features.
The create and remove operations are available only to logical interfaces. Any change to a user role interface policy takes effect only on users who log in with the user role after the change. Examples # Deny the user role role1 to access any interface. system-view [Sysname] role name role1 [Sysname-role-role1] interface policy deny [Sysname-role-role1-ifpolicy] quit # Deny the user role role1 to access any interface but FortyGigE 1/0/1 to FortyGigE 1/0/5.
Usage guidelines To permit a user role to access an interface after you configure the interface policy deny command, you must add the interface to the permitted interface list of the policy. With the user role, you can perform the following operations to the interfaces in the permitted interface list: • Create, remove, configure them (only interfaces in the permitted interface list). • Enter their views. • Specify them in a feature command.
permit vlan Use permit vlan to configure a list of VLANs accessible to a user role. Use undo permit vlan to remove the permission for a user role to access specific VLANs. Syntax permit vlan vlan-id-list undo permit vlan [ vlan-id-list ] Default No permitted VLANs are configured in user role interface policy view. Views User role VLAN policy view Predefined user roles network-admin Parameters vlan-id-list: Specifies a space-separated list of up to 10 VLAN items.
system-view [Sysname] interface fortygige 1/0/1 [Sysname-FortyGigE1/0/1] port access vlan 100 # Verify that you cannot create VLAN 101 or enter its view. system-view [Sysname] vlan 101 Permission denied. Related commands • display role • role • vlan policy deny role Use role to create a user role and enter user role view. If the user role has been created, you directly enter the user role view. Use undo role to delete a user role.
[Sysname-role-role1] Related commands • display role • interface policy deny • rule • vlan policy deny role default-role enable Use role default-role enable to enable the default user role feature for remote AAA users. Use undo role default-role enable to restore the default. Syntax role default-role enable undo role default-role enable Default The default user role function is disabled. AAA users who do not have a user role cannot log in to the device.
Syntax role feature-group name feature-group-name undo role feature-group name feature-group-name Default Two user role feature groups, L2 and L3, are created. Views System view Predefined user roles network-admin Parameters name feature-group-name: Specifies a feature group name. The feature-group-name argument is a case-sensitive string of 1 to 31 characters. Usage guidelines Assign a set of features to a user role feature group for easy permission assignment management.
Views User role view Predefined user roles network-admin Parameters number: Specifies a rule number in the range of 1 to 256. deny: Denies access to any specified command. permit: Permits access to any specified command. command command-string: Specifies a command string. The command-string argument is a case-sensitive string of 1 to 128 characters, including the wildcard asterisk (*), the delimiters space and tab, and all printable characters.
Access to the file system commands is controlled by both the file system command rules and the file system feature rule. A command with output redirection to the file system is permitted only when the command type write is assigned to the file system feature. When you specify a command string, follow the guidelines in Table 8.
Rule To control the access to a command, you must specify the command immediately after the view that has the command. Do not include the vertical bar (|), greater-than sign (>), or double greater-than sign (>>) when you specify display commands in a user role command rule. Guidelines To control access to a command, you must specify the command immediately behind the view to which the command is assigned. The rules that control command access for any subview do not apply to the command.
Syntax super [ rolename ] Views User view Predefined user roles network-admin Parameters rolename: Specifies a user role, a case-sensitive string of 1 to 63 characters. The user role must exist in the system. If no user role is specified, this command authorizes the user role network-admin to the user. Usage guidelines To enable users to obtain the user role that you are not logged in with, you must configure user role authentication.
Views System view Predefined user roles network-admin Parameters local: Enables local password authentication. scheme: Enables remote AAA authentication. Usage guidelines For local password authentication, use the super password command to set a password. For remote AAA authentication, set the username and password on the RADIUS or HWTACACS server.
super password [ role rolename ] undo super password [ role rolename ] Default No password is set for a user role. Views System view Predefined user roles network-admin Parameters role rolename: Specifies a user role, a case-sensitive string of 1 to 63 characters. The user role must exist in the system. If you do not specify a user role, this command sets a password for the user role network-admin. hash: Sets a hashed password. simple: Sets a plaintext password.
Syntax vlan policy deny undo vlan policy deny Default A user role has no access to any VLAN. Views User role view Predefined user roles network-admin Usage guidelines The vlan policy deny command denies the access of a user role to any VLAN. To restrict the VLAN access of a user role to only a set of VLANs: 1. Use vlan policy deny to deny access to any VLAN. 2. Use permit vlan to specify accessible VLANs.
FTP commands The device supports the FIPS mode that complies with NIST FIPS 140-2 requirements. Support for features, commands, and parameters might differ in FIPS mode and non-FIPS mode. For more information about FIPS mode, see Security Configuration Guide. FTP is not supported in FIPS mode. The switch has one built-in MPU. The slot number of this MPU is fixed at 0. FTP server commands display ftp-server Use display ftp-server to display FTP server configuration and status information.
display ftp-user Use display ftp-user to display detailed information about logged-in FTP users. Syntax display ftp-user Views Any view Predefined user roles network-admin network-operator Examples # Display detailed information about logged-in FTP users. display ftp-user UserName HostIP Port HomeDir root 192.168.20.
Predefined user roles network-admin Parameters username: Specifies a username. You can use the display ftp-user command to display FTP user information. Examples # Release the FTP connections established by using the user account ftpuser. free ftp user ftpuser Are you sure to free FTP connection? [Y/N]:y free ftp user-ip Use free ftp user-ip to manually release the FTP connections established from a specific IPv4 address.
Views System view Predefined user roles network-admin Parameters acl-number: Specifies an IPv4 ACL number in the range of 2000 to 3999. Usage guidelines You can use this command to permit only FTP requests from specific FTP clients. This configuration takes effect only for FTP connections to be established. It does not impact existing FTP connections. If you execute the command multiple times, the most recently specified ACL takes effect. Examples # Use ACL 2001 to allow only client 1.1.1.
[Sysname] ftp server dscp 30 ftp server enable Use ftp server enable to enable the FTP server. Use undo ftp server enable to disable the FTP server. Syntax ftp server enable undo ftp server enable Default The FTP server is disabled. Views System view Predefined user roles network-admin Examples # Enable the FTP server. system-view [Sysname] ftp server enable ftp timeout Use ftp timeout to set the idle-timeout interval for FTP connections. Use undo ftp timeout to restore the default.
Examples # Set the idle-timeout interval to 36 minutes. system-view [Sysname] ftp timeout 36 FTP client commands Before executing FTP client configuration commands, make sure you have configured authorization settings for users on the FTP server. Authorized operations include viewing the files in the working directory, reading/downloading/uploading/renaming/removing files, and creating directories.
Default The file transfer mode is binary. Views FTP client view Predefined user roles network-admin Usage guidelines You can perform this operation only after you log in to the FTP server. The carriage return characters vary with operating systems. For example, HP and Windows use /r/n, and Linux uses /n. To transfer files between two systems that use different carriage return characters, select the FTP transfer mode according to the file type.
• ASCII mode—Transfers text files. Examples # Set the file transfer mode to binary. ftp> binary 200 TYPE is now 8-bit binary Related commands ascii bye Use bye to terminate the connection to the FTP server and return to user view. If no connection is established between the device and the remote FTP server, use this command to return to user view. Syntax bye Views FTP client view Predefined user roles network-admin Examples # Terminate the connection to the FTP server and return to user view.
does not change the current working directory. If no drive information is provided, the argument represents a folder or subfolder in the current directory. For more information about the drive and path arguments, see Fundamentals Configuration Guide. ..: Returns to the upper directory. Executing the cd .. command is the same as executing the cdup command. If the current working directory is the FTP root directory, the cd .. command does not change the current working directory.
Examples # Change the working directory to the upper directory. ftp> pwd 257 "/ftp/subdir" is your current location ftp> cdup 250 OK. Current directory is /ftp ftp> pwd 257 "/ftp" is your current location Related commands • cd • pwd close Use close to terminate the connection to the FTP server without exiting FTP client view. Syntax close Views FTP client view Predefined user roles network-admin Usage guidelines You can perform this operation only after you log in to the FTP server.
Predefined user roles network-admin Usage guidelines When FTP client debugging is enabled, executing this command disables FTP client debugging. When FTP client debugging is disabled, executing this command enables FTP client debugging. Examples # Enable and then disable FTP client debugging. ftp> debug Debugging on (debug=1). ftp> debug Debugging off (debug=0). delete Use delete to permanently delete a file on the FTP server.
Views FTP client view Predefined user roles network-admin Parameters remotefile: Specifies the name of a file or directory on the FTP server. localfile: Specifies the name of the local file used for saving the displayed information. Usage guidelines You can perform this operation only after you log in to the FTP server. In FTP client view, executing the dir command is the same as executing the ls command.
disconnect Use disconnect to terminate the connection to the FTP server without exiting FTP client view. Syntax disconnect Views FTP client view Predefined user roles network-admin Usage guidelines You can perform this operation only after you log in to the FTP server. Examples # Terminate the connection to the FTP server without exiting the FTP client view. ftp> disconnect 221-Goodbye. You uploaded 0 and downloaded 0 kbytes. 221 Logout.
Syntax ftp [ ftp-server [ service-port ] [ dscp dscp-value | source { interface interface-type interface-number | ip source-ip-address } ] ] * Views User view Parameters ftp-server: Specifies the IPv4 address or host name of an FTP server. A host name can be a case-insensitive string of 1 to 253 characters. Valid characters for a host name include letters, digits, hyphens (-), underscores (_), and dots (.). service-port: Specifies the TCP port number of the FTP server, in the range of 0 to 65535.
ftp client source Use ftp client source to specify the source IPv4 address for outgoing FTP packets. Use undo ftp client source to restore the default. Syntax ftp client source { interface interface-type interface-number | ip source-ip-address } undo ftp client source Default No source IPv4 address is configured for outgoing FTP packets. The device uses the primary IPv4 address of the output interface for the route to the server as the source IP address.
Views FTP client view Predefined user roles network-admin Parameters remotefile: Specifies the name of the file to be downloaded. localfile: Specifies a name for the downloaded file. Usage guidelines You can perform this operation only after you log in to the FTP server. To save the downloaded file to the working directory accessed by the ftp command, the localfile argument must specify a file name such as a.cfg. If you do not provide the localfile argument, the downloaded file uses its original name.
Syntax help [ command-name ] Views FTP client view Predefined user roles network-admin Parameters command-name: Specifies a command supported by the FTP client. Usage guidelines In FTP client view, executing the help command is the same as entering?. Examples # Display all commands supported by the FTP client. ftp> help Commands may be abbreviated.
Parameters directory: Specifies a local directory of the FTP client. There must be a slash sign (/) before the name of the storage medium, for example, /flash:/logfile. /: Specifies the root directory of the FTP client. Examples # Display the local working directory. ftp> lcd Local directory now /flash: # Change the local working directory to flash:/logfile.
drwxr-xr-x 2 0 0 8192 Jul 5 09:15 logfile drwxr-xr-x 2 0 0 8192 Jul 2 14:33 seclog -rwxr-xr-x 1 0 0 40808448 Jul -rwxr-xr-x 1 0 0 3050 Jul 7 12:26 startup.cfg -rwxr-xr-x 1 0 0 54674 Jul 4 09:24 startup.mdb -rwxr-xr-x 1 0 0 1481 Jul 2 14:33 simware-cmw710-sys tem-a1801.bin 7 12:34 x.cfg 226 11 matches total # Save detailed information about file a.txt to s.txt. ftp> ls a.txt s.txt output to local-file: s.txt ? [Y/N]y 150 Connecting to port 50203 226-Glob: a.
newer Use newer to update a local file by using a remote file on the FTP server. Syntax newer remotefile [ localfile ] Views FTP client view Predefined user roles network-admin Parameters remotefile: Specifies the name of the remote file on the FTP server. localfile: Specifies the name of the local file to be updated. Usage guidelines You can perform this operation only after you log in to the FTP server.
Usage guidelines After you issue this command, the system will prompt you to enter the username and password. After you log in to one FTP server, you must disconnect from the server before you can use the open command to log in to another server. Examples # In FTP client view, log in to the FTP server 192.168.40.7. ftp ftp> open 192.168.40.7 Press CTRL+C to abort. Connected to 192.168.40.7 (192.168.40.7). 220 FTP service ready. User (192.168.40.7:(none)): root 331 Password required for root.
put Use put to upload a file on the client to the remote FTP server. Syntax put localfile [ remotefile ] Views FTP client view Predefined user roles network-admin Parameters localfile: Specifies the name of the local file to be uploaded. remotefile: Specifies the file name for saving the uploaded file on the FTP server. Usage guidelines You can perform this operation only after you log in to the FTP server.
pwd Use pwd to display the currently accessed directory on the FTP server. Syntax pwd Views FTP client view Predefined user roles network-admin Usage guidelines You can perform this operation only after you log in to the FTP server. Examples # Display the currently accessed directory on the remote FTP server. ftp> cd subdir 250 OK. Current directory is /subdir ftp> pwd 257 "/subdir" is your current location quit Use quit to terminate the connection to the FTP server and return to user view.
Syntax reget remotefile [ localfile ] Views FTP client view Predefined user roles network-admin network-operator Parameters remotefile: Specifies the name of the file on the FTP server. localfile: Specifies the name of the local file. Usage guidelines You can perform this operation only after you log in to the FTP server.
Examples # Rename the file a.txt as b.txt: • Method 1 ftp> rename (from-name) a.txt (to-name) b.txt 350 RNFR accepted - file exists, ready for destination 250 File successfully renamed or moved • Method 2 ftp> rename a.txt (to-name) b.txt 350 RNFR accepted - file exists, ready for destination 250 File successfully renamed or moved • Method 3 ftp> rename a.txt b.
Parameters marker: Specifies the retransmit marker. Usage guidelines You can perform this operation only after you log in to the FTP server. Support for this command varies with FTP servers. Examples # Retransmit the file h.c (82 bytes) from 2 bytes. ftp> restart 2 restarting at 2. execute get, put or append to initiate transfer ftp> put h.c h.c local: h.c remote: h.c 350 Restart position accepted (2). 150 Ok to send data. 226 File receive OK. 80 bytes sent in 0.000445 seconds (175.
DELE MKD XMKD RMD XRMD ABOR SIZE RNFR RNTO 4 UNIX Type: L8 Table 11 Command output Field Description USER Username, corresponding to the xx command in FTP client view. PASS Password. NOOP Null operation. SYST System parameters. TYPE Request type. CWD Changes the current working directory. XCWD Extended command with the meaning of CWD. PWD Prints the working directory. CDUP Changes the directory to the upper directory. XCUP Extended command with the meaning of CDUP.
rmdir Use rmdir to permanently delete a directory on the FTP server. Syntax rmdir directory Views FTP client view Predefined user roles network-admin Parameters directory: Specifies the name of a directory on the remote FTP server. Usage guidelines You can perform this operation only after you log in to the FTP server. To perform this operation, you must have delete permission on the FTP server. Delete all files and subdirectories in a directory before you delete the directory.
Support for this command varies with FTP servers. Examples # Display FTP server status. ftp> rstatus 211-FTP server status: Connected to 192.168.20.177 Logged in as root TYPE: ASCII No session bandwidth limit Session timeout in seconds is 300 Control connection is plain text Data connections will be plain text At session startup, client count was 1 vsFTPd 2.0.
Field Description The first bit specifies the file type: -rw-r--r-- • • • • • • • -—Common. B—Block. c—Character. d—Directory. l—Symbol connection file. p—Pipe. s—socket. The second bit through the tenth bit are divided into three groups. Each group contains three characters, representing the access permission of the owner, group, and other users. • • • • -—No permission. r—Read permission. w—Write permission. x—Execution permission. 1 Number of connections. 0 Name of the file owner.
Case: off; CR stripping: on Ntrans: off Nmap: off Hash mark printing: off; Use of PORT cmds: on Table 14 Command output Field Description Connected to 192.168.1.56. IP address of the FTP server that is connected to the FTP client. Verbose: on; Bell: off; Prompting: on; Globbing: off Displays debugging information. Store unique: off; Receive unique: off The name of the file on the FTP server is unique and the name of the local file is unique.
Views FTP client view Predefined user roles network-admin Parameters username: Specifies the username of the target user account. password: Specifies the password of the target user account. Usage guidelines You can perform this operation only after you log in to the FTP server. The username and password of the target user account must have been configured. Otherwise, the user account change operation fails and the FTP connection is closed.
ftp> verbose Verbose mode off. # Execute the get command. ftp> verbose Verbose mode off. ftp> get a.txt # Enable the device to display detailed information about FTP operations. ftp> verbose Verbose mode on. # Execute the get command. ftp> get a.txt local: a.txt remote: a.txt 150 Connecting to port 47455 226 File successfully transferred 1569 bytes received in 0.0117 seconds (130.8 kbyte/s) ? Use ? to display all commands supported by an FTP client.
# Display the help information for the dir command.
TFTP commands The device supports the FIPS mode that complies with NIST FIPS 140-2 requirements. Support for features, commands, and parameters might differ in FIPS mode and non-FIPS mode. For more information about FIPS mode, see Security Configuration Guide. TFTP is not supported in FIPS mode. tftp Use tftp to download a file from the TFTP server to the local device or upload a local file to the TFTP server in an IPv4 network.
• interface interface-type interface-number: Specifies an interface by its type and number. The primary IPv4 address of this interface will be used as the source IPv4 address for outgoing TFTP packets. Make sure the interface is up and has the primary IPv4 address configured. Otherwise, the transmission fails. • ip source-ip-address: Specifies an IPv4 address. This address must be the IPv4 address of an interface in up state. Otherwise, the transmission fails.
Default No source IPv4 address is configured for outgoing TFTP packets. The device uses the primary IPv4 address of the output interface for the route to the server as the source IP address. Views System view Predefined user roles network-admin Parameters interface interface-type interface-number: Specifies the source interface for establishing TFTP connections. The primary IPv4 address of the source interface is used as the source IPv4 address for packets sent to a TFTP server.
Parameters acl-number: Specifies the number of a basic ACL, in the range of 2000 to 2999. Usages guidelines You can use an ACL to deny or permit the device's access to specific TFTP servers. Examples # Allow the device to access only the TFTP server at 1.1.1.1. System-view [Sysname] acl number 2000 [Sysname-acl-basic-2000] rule permit source 1.1.1.
File system management commands IMPORTANT: • Before managing storage media, files, and directories, make sure you know the possible impacts. • A file or directory whose name starts with a period (.) is considered a hidden file or directory. Do not give a common file or directory a name that starts with a period. • Some system files and directories are hidden. A file name must be specified in one of the file name formats allowed. For more information, see Fundamentals Configuration Guide.
# In IRF mode, change to the Flash root directory of the global standby MPU that resides in member device 2. cd chassis2#slot0#flash:/ # In IRF mode, change back to the Flash root directory of the global active MPU. cd flash:/ copy Use copy to copy a file. Syntax copy fileurl-source fileurl-dest Views User view Predefined user roles network-admin Parameters fileurl-source: Specifies the name or URL of the file to be copied.
Examples # Copy the test.cfg file in the current folder and save it to the current folder as testbackup.cfg. copy test.cfg testbackup.cfg Copy flash:/test.cfg to flash:/testbackup.cfg?[Y/N]:y Copying file flash:/test.cfg to flash:/testbackup.cfg...Done. # Copy 1.cfg from the Flash's test folder to the USB disk's first partition, and save it to the testbackup folder as 1backup.cfg. copy flash:/test/1.cfg usb0:/testbackup/1backup.cfg Copy flash:/test/1.cfg to usb0:/testbackup/1backup.
Views User view Predefined user roles network-admin Parameters /unreserved: Permanently deletes the specified file. If you do not specify this keyword, the command moves the file to the recycle bin. file-url: Specifies the name of the file to be deleted. Asterisks (*) are acceptable as wildcards. For example, to remove files with the .txt extension in the current directory, enter delete *.txt. Usage guidelines Use the delete /unreserved file-url command with caution.
• Method 1 delete chassis2#slot0#flash:/1.cfg Delete chassis2#slot0#flash:/1.cfg?[Y/N]:y Deleting file chassis2#slot0#flash:/1.cfg...Done. • Method 2 cd chassis2#slot0#flash:/ delete 1.cfg Delete chassis2#slot0#flash:/1.cfg?[Y/N]:y Deleting file chassis2#slot0#flash:/1.cfg...Done. Related commands • reset recycle-bin • undelete dir Use dir to display files or folders.
Directory of flash:/ ... Directory of usb0:/ ... # In IRF mode, display information about all files and folders in the storage media of the master. dir /all Directory of flash:/ ... # In IRF mode, display files and folders in the root directory of every storage medium in the IRF fabric. dir /all-filesystems Directory of flash:/ ... Directory of chassis2#slot0#flash:/ ...
Syntax fdisk medium-name [ partition-number ] Views User view Predefined user roles network-admin Parameters medium-name: Specifies the name of the storage medium to be partitioned. partition-number: Specifies the number of partitions, in the range of 1 to 4. Usage guidelines The Flash cannot be partitioned. If the partition-number argument is specified, the storage medium is divided into the specified number of partitions. Otherwise, partitioning is performed in an interactive way.
# Divide the USB disk on the device into three partitions and specify the size for each partition: fdisk usb: The capacity of usb: : 256M bytes Partition 1 (32MB~224MB, 256MB, Press CTRL+C to quit or Enter to use all available space):128 // Enter 128 to set the size of the first partition to 128 MB. Partition 2 (32MB~96MB, 128MB, Press CTRL+C to quit or Enter to use all available space):31 // Enter 31 to set the size of the second partition to 31 MB.
quiet: Gives no confirmation prompt for file or folder operations. Usage guidelines In quiet mode, the system does not prompt for confirmation when a user performs a file or folder operation. The alert mode provides an opportunity to cancel a disruptive operation. Examples # Set the file and folder operation mode to alert. system-view [Sysname] file prompt alert fixdisk Use fixdisk to check a storage medium for damage and repair any damage.
Parameters medium-name: Specifies the name of a storage medium. Usage guidelines Formatting a storage medium permanently deletes all files on the storage medium. If a startup configuration file exists on the storage medium, back it up if necessary. To format a partitioned storage medium, you must format the partitions individually. You cannot use the format usb command to format the medium as a whole. You can format a storage medium only when no one is accessing the medium. Examples # Format the Flash.
Decompressing file system.bin.gz... Done. 3. Verify the decompress operation. dir system.* Directory of flash: 1 -rw- 0 May 30 2012 11:42:25 system.bin 472972 KB total (472844 KB free) gzip Use gzip to compress a file. Syntax gzip filename Views User view Predefined user roles network-admin Parameters filename: Specifies the name of the file to be compressed. The compressed file will be saved to file filename.gz.
Views User view Predefined user roles network-admin network-operator Parameters file-url: Specifies the name of a file. Usage guidelines The digest can be used to verify the integrity of the file. For example, you can use this command to calculate the digest of a software image file and compare it with that provided on the HP website to identify whether the file has been tampered with. Examples # Use the MD5 algorithm to calculate the digest of file system.bin. md5sum system.
Creating directory flash:/test/subtest... Done. # In standalone mode, create the test folder. mkdir test Creating directory flash:/test... Done. # In IRF mode, create the test folder on the master. mkdir test Creating directory flash:/test... Done. # In IRF mode, create the test folder on the global standby MPU that resides in member device 2. mkdir chassis2#slot0#flash:/test Creating directory chassis2#slot0#flash:/test... Done.
telnet server enable # ---- More ---- # In IRF mode, display the contents of the testcfg.cfg file on the master. more testcfg.cfg # version 7.1.045, Ess 2106 # sysname Sysname # telnet server enable # ---- More ---- # In IRF mode, display the contents of the testcfg.cfg file on the global standby MPU that resides in member device 2. more chassis2#slot0#flash:/testcfg.cfg # version 7.1.
To mount a partitioned storage medium, you must mount all the partitions individually, instead of mounting the storage medium as a whole. Examples # In standalone mode, mount a USB disk. mount usb0: # In IRF mode, mount a USB disk on the master. mount usb0: # In IRF mode, mount a USB disk on the MPU that resides in member device 2. mount chassis2#slot0#usb0: Related commands umount move Use move to move a file.
Syntax pwd Views User view Predefined user roles network-admin Examples # Display the current working directory. pwd flash: rename Use rename to rename a file or folder. Syntax rename fileurl-source fileurl-dest Views User view Predefined user roles network-admin Parameters fileurl-source: Specifies the name of the source file or folder. fileurl-dest: Specifies the name of the destination file or folder.
Parameters /force: Deletes all files in the recycle bin without prompting for confirmation. If you do not specify this option, the command prompts you to confirm the deletion. Usage guidelines The delete file-url command only moves a file to the recycle bin. To permanently delete the file, use the reset recycle-bin command to clear the recycle bin. If a file is corrupted, you might not be able to delete the file by using the reset recycle-bin command. In this case, use the reset recycle-bin /force command.
Remove directory flash:/test/subtest and the files in the recycle-bin under this directory will be deleted permanently. Continue?[Y/N]:y Removing directory flash:/test/subtest... Done. sha256sum Use sha256sum to use the SHA-256 algorithm to calculate the digest of a file. Syntax sha256sum file-url Views User view Predefined user roles network-admin Parameters file-url: Specifies the name of a file. Usage guidelines The digest can be used to verify the integrity of the file.
verbose: Displays the names of the successfully archived files and folders. source fileurl-source-list&<1-5>: Specifies the files and folders to be archived. The fileurl-source-list argument can be a space-separated list of up to five items. Each item can be a file or folder name. Examples # Archive file a.cfg to file a.tar. tar create archive-file a.tar source a.cfg Creating archive a.tar …… Done. # Compress file a.cfg and archive the file to a.tar.gz. tar create gz archive-file a.
# Extract files and folders, and display their content on the screen. tar extract archive-file a.tar.gz verbose screen a.cfg # version 7.1.045, Ess 2106 # sysname Sysname # # Extract files and folders, save them to the same folder as the archive file, and display the names of the archived files and folders. tar extract archive-file a.tar.gz verbose a.txt # Extract files and folders, and save them to the path flash:/a. tar extract archive-file a.tar.
Syntax umount medium-name Default A storage medium is automatically mounted and placed in mounted state. Views User view Predefined user roles network-admin Parameters medium-name: Specifies the name of a storage medium. Usage guidelines Before you remove a mounted storage medium from the system, first unmount it to avoid damaging the medium. Before you unmount a storage medium, make sure no other users are accessing the medium. Otherwise, the unmount operation fails.
Parameters file-url: Specifies the name of the file to be restored. Usage guidelines If another file that has the same name exists in the directory, the system prompts you about whether to overwrite the existing file. If you enter Y, the existing file is overwritten. If you enter N, the command is not executed. Examples # Restore the copy.cfg file, which was moved from the flash: directory to the recycle bin. undelete copy.cfg Undelete flash:/copy.cfg?[Y/N]:y Undeleting file flash:/copy.cfg...
Configuration file management commands The device supports the FIPS mode that complies with NIST FIPS 140-2 requirements. Support for features, commands, and parameters might differ in FIPS mode and non-FIPS mode. For more information about FIPS mode, see Security Configuration Guide. backup startup-configuration Use backup startup-configuration to back up the main next-startup configuration file to a TFTP server.
Default Configuration encryption is disabled. The running configuration is saved to a configuration file without encryption. Views System view Predefined user roles network-admin Parameters private-key: Encrypts configuration with a private key. Any HP device running Comware V7 software can decrypt the encrypted configuration file. public-key: Encrypts configuration with a public key. Any HP device can decrypt the encrypted configuration file.
Typically, this command does not display parameters that are set to their default settings. If the system has automatically changed the setting you have made for a parameter, for example, due to a system restriction, this command displays the effective setting rather than the configured one. Examples # Display local user configuration.
display saved-configuration Use display saved-configuration to display the contents of the configuration file for the next system startup. Syntax display saved-configuration Views Any view Predefined user roles network-admin network-operator Usage guidelines Use this command to verify that important settings have been saved to the configuration file for the next system startup. This command selects the configuration file to display in the following order: 1.
Views Any view Predefined user roles network-admin network-operator Usage guidelines Current startup configuration file is the configuration file that has been loaded. Next-startup configuration file is the configuration file used at the next startup. In IRF mode, the standby MPUs in the IRF fabric always use the same current startup configuration file as the global active MPU. Examples # In standalone mode, display startup configuration files.
Field Description Next backup startup saved-configuration file Backup configuration file to be used at the next startup. (This file does not exist.) If the specified next-startup configuration file has been deleted, this comment appears next to the file name. Chassis x Slot n Displays the startup configuration files on the MPU in slot n of IRF member x. Related commands startup saved-configuration display this Use display this to display the running configuration in the current view.
line aux 0 user-role network-operator # line vty 0 63 authentication-mode none user-role network-admin user-role network-operator # return reset saved-configuration Use reset saved-configuration to delete next-startup configuration files. Syntax reset saved-configuration [ backup | main ] Views User view Predefined user roles network-admin Parameters backup: Deletes the backup next-startup configuration file. main: Deletes the main next-startup configuration file.
Configuration file in flash is being cleared. Please wait ... .. MainBoard: Configuration file is cleared. # In IRF mode, delete the backup next-startup configuration file. reset saved-configuration backup The saved configuration file will be erased. Are you sure? [Y/N]:y Configuration file in flash is being cleared. Please wait ... .. MainBoard: Configuration file is cleared.
Examples # In standalone mode, download the configuration file config.cfg from the TFTP server at 2.2.2.2, and specify the file as the main next-startup configuration file. restore startup-configuration from 2.2.2.2 config.cfg Restoring the next startup-configuration file from 2.2.2.2. Please wait...finished. Now restoring the next startup-configuration file from main board to backup board. Please wait...finished. # In IRF mode, download the configuration file config.
slot slot-number: Saves the running configuration to the MPU. (In standalone mode.) chassis chassis-number slot slot-number: Saves the running configuration to an MPU. To save the running configuration only to the global active MPU, do not specify this option or the all keyword. (In IRF mode.) safely: Saves the configuration file in safe mode. If this keyword is not specified, the device saves the configuration file in fast mode. Safe mode is slower than fast mode, but more secure.
# In standalone mode, save the running configuration to a file in the root directory of the flash memory, and specify the file as the main next-startup configuration file. save The current configuration will be written to the device. Are you sure? [Y/N]:y Please input the file name(*.cfg)[flash:/startup.cfg] (To leave the existing filename unchanged, press the enter key): Validating file. Please wait... Saved the current configuration to mainboard device successfully.
Predefined user roles network-admin Parameters cfgfile: Specifies the name of a .cfg file. This .cfg file must already exist in the root directory of storage medium. backup: Specifies the configuration file as the backup next-startup configuration file. main: Specifies the configuration file as the main next-startup configuration file. This is the primary configuration file that the device attempts to load at startup.
Software upgrade commands The switch has one built-in MPU. The slot number of this MPU is fixed at 0. Unless otherwise stated, the term "card" in this document refers to both the MPU and LPUs. boot-loader file Use boot-loader file to specify startup software image files.
backup: Specifies the files as backup startup files. Backup startup images are used only when main images are not available. main: Specifies the files as main startup files. The device always first attempts to start up with main startup files. Usage guidelines In standalone mode, use this command to upgrade the startup software images on the MPU. Before you execute this command, you must save the upgrade files to the root directory of a storage medium on the MPU.
system.bin ssh.bin This command will set the backup startup software images. Continue? [Y/N]:Y Add images to target slot. flash:/boot.bin already exists on chassis 1 slot 0. flash:/system.bin already exists on chassis 1 slot 0. flash:/ssh.bin already exists on chassis 1 slot 0. Overwrite it? [Y/N]:y Decompressing file boot.bin to flash:/boot.bin....................................Done. Decompressing file system.bin to flash:/system.bin................................Done.
Startup image synchronization fails if any software image being synchronized is not available or is corrupted. Examples # In IRF mode, synchronize startup images from the global active MPU to the MPU in slot 0 on IRF member device 1. boot-loader update chassis 1 slot 0 This command will update the specified standby MPU. Continue? [Y/N]:y Updating. Please wait... Copying main startup software images to chassis 1 slot 0. Please wait... Done.
If the BootWare image in the Normal area is corrupted or requires a version rollback, use the bootrom restore command to copy the BootWare image in the Backup area to the Normal area. Examples # Back up the entire BootWare image from the Normal area to the Backup area. bootrom backup all Now backuping the Boot ROM, please wait... ......Done.
Related commands bootrom backup bootrom update Use bootrom update to load the BootWare image in a storage medium to the Normal area of BootWare. Syntax In standalone mode: bootrom update file file-url slot slot-number-list In IRF mode: bootrom update file file-url chassis chassis-number slot slot-number-list Views User view Predefined user roles network-admin Parameters file file-url: Specifies a .bin BootWare image file path, a string of 1 to 63 characters.
bootrom update file flash:/boot.bin chassis 1 slot 0 This command will update the Boot ROM file on the specified board(s), Continue? [Y/N]:y Now updating the Boot ROM, please wait... .............Done. Related commands boot-loader file bootrom-update security-check enable Use bootrom-update security-check enable to enable BootWare image validity check. Use undo bootrom-update security-check enable to disable BootWare image validity check.
Predefined user roles network-admin network-operator Parameters slot slot-number: Specifies the slot number of the MPU. (In standalone mode.) chassis chassis-number [slot slot-number ]: Specifies an IRF member device or the MPU on an IRF member device. The chassis-number argument represents the IRF member ID of the device, and the slot-number argument represents the slot number of the MPU on the device.
Field Description Main startup software images Main Comware images for the next startup. Backup startup software images Backup Comware images for the next startup.
Device management commands The switch has one built-in MPU. The slot number of this MPU is fixed at 0. Unless otherwise stated, the term "card" in this document refers to both the MPU and LPUs. clock datetime Use clock datetime to set the UTC time. Syntax clock datetime time date Default The factory default UTC time is used. Views User view Predefined user roles network-admin Parameters time: Specifies a time in the format hh:mm:ss.
• clock timezone • display clock clock protocol Use clock protocol to specify the system time source. Use undo clock protocol to restore the default. Syntax clock protocol { none | ntp } undo clock protocol Default The device uses NTP to get the system time. Views System view Predefined user roles network-admin Parameters none: Uses the local clock. After you specify this keyword, you can use the clock datetime, clock timezone, or clock summer-time command to change the system time.
Views System view Pre-defined user roles network-admin Parameters name: Specifies a name for the daylight saving time schedule, a case-sensitive string of 1 to 32 characters. start-time: Specifies the start time in the format hh:mm:ss. The hh value is in the range of 0 to 23, the mm value is in the range of 0 to 59, and the ss value is in the range of 0 to 59. The leading zero in a segment can be omitted. If the seconds segment is 0 (hh:mm:00), you can omit it.
A correct system time setting is essential to network management and communication. Set the system time correctly or use NTP to synchronize your device with a trusted time source before you run it on the network. Examples # Set the system time ahead 1 hour for the period between 06:00:00 on 08/01 and 06:00:00 on 09/01.
Examples # Set the name of the local time zone to Z5, and add 5 hours to the UTC time. system-view [Sysname] clock timezone Z5 add 5 Related commands • clock datetime • clock protocol • clock summer-time • display clock command Use command to assign a command to a job. Use undo command to revoke a command. Syntax command id command undo command id Default No command is assigned to a job.
[Sysname-job-backupconfig] command 2 tftp 192.168.100.11 put flash:/startup.cfg backup.cfg Related commands scheduler job copyright-info enable Use copyright-info enable to enable displaying the copyright statement. Use undo copyright-info enable to disable displaying the copyright statement. Syntax copyright-info enable undo copyright-info enable Default The copyright statement is displayed. Views System view Predefined user roles network-admin Examples # Enable displaying the copyright statement.
# Disable displaying the copyright statement. system-view [Sysname] undo copyright-info enable • When a Telnet user logs in, the user view prompt appears: • When a console user quits user view, the following message appears (the device automatically tries to restart the console session): User interface aux0 is available. Press ENTER to get started. display alarm Use display alarm to display alarm information.
Table 20 Command output Field Description Slot Slot number of the card with an alarm. If the value is a hyphen (-), the alarm was generated by the chassis. (In standalone mode.) Level Alarm severity. Possible values include ERROR, WARNING, NOTICE, and INFO, in descending order. Info Detailed alarm information. faulty The card is starting up or is faulty. # In IRF mode, display alarm information.
Time Zone : Z5 add 05:00:00 # Display the system time and date when the local time zone Z5 and daylight saving time PDT are specified. display clock 15:11:00 Z5 Fri 03/16/2012 Time Zone : Z5 add 05:00:00 Summer Time : PDT 06:00:00 08/01 06:00:00 09/01 01:00:00 Related commands • clock datetime • clock summer-time • clock timezone display copyright Use display copyright to display the copyright statement, including software and hardware copyright statements.
Parameters slot slot-number: Specifies a card by its slot number. Without this option, the command displays the CPU usage statistics for all cards. (In standalone mode.) chassis chassis-number slot slot-number: Specifies a card on an IRF member device by its slot number and the member ID. Without this option, the command displays the CPU usage statistics for all cards in the IRF fabric. (In IRF mode.) cpu cpu-number: Displays the CPU usage statistics. The cpu-number argument can only be 0.
Table 22 Command output Field Description 1% in last 5 seconds Average CPU usage during the last 5 seconds. 1% in last 1 minute Average CPU usage during the last minute. 1% in last 5 minutes Average CPU usage during the last 5 minutes. Slot x CPU y CPU usage Usage statistics for CPU y of the card in slot x. (In standalone mode.) Chassis x Slot y CPU z CPU usage Usage statistics for CPU z of the card in slot y on member device x. (In IRF mode.
In IRF mode: display cpu-usage history [ job job-id ] [ chassis chassis-number slot slot-number [ cpu cpu-number ] ] Views Any view Predefined user roles network-admin network-operator Parameters job job-id: Specifies a process by its ID. Without this option, the command displays the historical CPU usage statistics for the entire system, which is the sum of the historical CPU usage statistics for all processes in the system.
40%| 35%| 30%| 25%| 20%| 15%| # 10%| 5%| ### # ######## -----------------------------------------------------------10 20 30 40 50 60 (minutes) cpu-usage (CPU 0) last 60 minutes (SYSTEM) The output shows the historical CPU usage statistics for the entire system (with the name SYSTEM) in the last 60 minutes: • 5%: 12 minutes ago • 10%: 13 minutes ago • 15%: 14 minutes ago • 10%: 15 minutes ago • 5%: 16 and 17 minutes ago • 10%: 18 minutes ago • 5%: 19 minutes ago • 2% or lower tha
The output shows the historical CPU usage statistics of process 1 (with the process name scmd) in the last 60 minutes. A process name with square brackets ([ ]) means that the process is a kernel process. • 5%: 20 minutes ago • 2% or lower than 2%: Other time display device Use display device to display device information.
Table 23 Command output Field Description Slot No. Slot number of the card. Brd Type Hardware type of the card. Card status: • • • • Brd Status Master—The card is the MPU. Absent—The slot is not installed with a card. Fault—The card is faulty and cannot start up. Normal—The card is an interface card and is operating correctly. Subslot Maximum number of subcards that the card supports. The switch does not support subcards. Sft Ver Software version of the card.
Field Description Patch Ver Patch version of the card. If no patch is installed, the value of this field is None. display device manuinfo Use display device manuinfo to display the electronic label information of the device.
VENDOR_NAME : HP Fan 1 DEVICE_NAME : HP FF 7904 Bck(Pwr)-Frt(Prt) Fan Tray JG839A DEVICE_SERIAL_NUMBER : 210231A2L1 MAC_ADDRESS : NONE MANUFACTURING_DATE : 2013-08-10 VENDOR_NAME : HP Fan 2 DEVICE_NAME : HP FF 7904 Bck(Pwr)-Frt(Prt) Fan Tray JG839A DEVICE_SERIAL_NUMBER : 21H1380011 MAC_ADDRESS : NONE MANUFACTURING_DATE : 2013-08-10 VENDOR_NAME : HP Power 2 DEVICE_NAME : HP FF 7900 1800w AC Frt(Prt)-Bck PSU JG840A DEVICE_SERIAL_NUMBER : 21A2KXH138 MAC_ADDRESS : NONE MANUFACTURING_DATE
DEVICE_SERIAL_NUMBER : 210231A2KV MAC_ADDRESS : 7425-8AC7-2DC4 MANUFACTURING_DATE : 2013-08-24 VENDOR_NAME : HP Fan 1 DEVICE_NAME : HP FF 7904 Bck(Pwr)-Frt(Prt) Fan Tray JG839A DEVICE_SERIAL_NUMBER : 210231A201 MAC_ADDRESS : NONE MANUFACTURING_DATE : 2013-08-10 VENDOR_NAME : HP Fan 2 DEVICE_NAME : HP FF 7904 Bck(Pwr)-Frt(Prt) Fan Tray JG839A DEVICE_SERIAL_NUMBER : 210231A2L1 MAC_ADDRESS : NONE MANUFACTURING_DATE : 2013-08-10 VENDOR_NAME : HP Power 2 DEVICE_NAME : HP FF 7900 1800w AC F
Views Any view Predefined user roles network-admin network-operator Parameters chassis chassis-number: Specifies an IRF member device by its member ID. (In IRF mode.) fan-id: Specifies a fan by its ID. The value range for the ID depends on the device model. Examples # In standalone mode, display the electronic label information of fan 2.
Parameters chassis chassis-number: Specifies an IRF member device by its member ID. (In IRF mode.) power-id: Specifies a power supply by its ID. Examples # In standalone mode, display the electronic label information of power supply 2.
This display command does not support the | by-linenum option, the > filename option, or the >> filename option. However, this command asks you whether you want to save the output to a file or display the output on the screen. The file used to save the output is automatically compressed to save storage space. Examples # Display the operating statistics for multiple feature modules in the system.
System temperature information (degree centigrade): ---------------------------------------------------------------------Slot Sensor Lower Warning Alarm Shutdown 0 hotspot 1 31 Temperature 0 75 85 90 0 hotspot 2 29 0 75 85 90 0 hotspot 3 40 0 65 80 85 0 hotspot 4 31 0 65 80 85 1 hotspot 1 26 0 80 95 98 1 hotspot 2 47 0 80 95 98 1 hotspot 3 44 0 80 95 98 # In IRF mode, display the temperature statistics for all temperature sensors in the IRF fabric.
display fan Use display fan to display the operating states of fans. Syntax In standalone mode: display fan [ fan-id ] In IRF mode: display fan [ chassis chassis-number [ fan-id ] ] Views Any view Predefined user roles network-admin network-operator Parameters chassis chassis-number: Specifies an IRF member device by its member ID. Without this option, the command displays the operating states of fans on all IRF member devices. (In IRF mode.) fan-id: Specifies a fan by its ID.
Airflow Direction: Unknown Fan Status Speed(rpm) --- ---------- ---------- 1 Normal 8051 2 Normal 6890 3 Normal 6854 4 Normal 7944 5 Normal 6868 6 Normal 7905 7 Normal 8019 8 Normal 6832 9 Normal 6885 10 Normal 7980 display memory Use display memory to display memory usage.
Slot 1: Total Used Free Shared Buffers Cached FreeRatio 3415304 679428 2735876 0 0 13024 80.1% -/+ Buffers/Cache: 666404 2748900 Mem: Swap: 0 0 0 # In IRF mode, display memory usage. display memory The statistics about memory is measured in KB: Chassis 1 Slot 0: Total Used Free Shared Buffers Cached FreeRatio 4037264 771628 3265636 0 68 173812 80.
display memory-threshold Use display memory-threshold to display memory alarm thresholds and statistics. Syntax In standalone mode: display memory-threshold [ slot slot-number ] In IRF mode: display memory-threshold [ chassis chassis-number slot slot-number ] Views Any view Predefined user roles network-admin Parameters slot slot-number: Specifies a card by its slot number. Without this option, the command displays the memory alarm thresholds and statistics for the MPU. (In standalone mode.
[Enter severe low-memory state] First notification at: 0.0 Latest notification at: 0.0 Total number of notifications sent: 0 [Back to severe low-memory state] First notification at: 0.0 Latest notification at: 0.0 Total number of notifications sent: 0 [Enter critical low-memory state] First notification at: 0.0 Latest notification at: 0.0 Total number of notifications sent: 0 display power Use display power to display power supply information.
Syntax display scheduler job [ job-name ] Views Any view Predefined user roles network-admin network-operator Parameters job-name: Specifies a job by its name, a case-sensitive string of 1 to 47 characters. Without this option, the command displays the configuration information of all jobs. Examples # Display the configuration information of all jobs. display scheduler job Job name: saveconfig copy startup.cfg backup.
Completion time : Tue Dec 27 10:44:47 2013 --------------------------------- Job output ----------------------------------system-view System View: return to User View with Ctrl+Z. [Sysname]interface range fortygige 1/0/1 to fortygige 1/0/3 [Sysname-if-range]shutdown Table 29 Command output Field Description Logfile Size Size of the log file, in bytes. Schedule name Schedule to which the job belongs. Execution time Time when the job was started.
Syntax display scheduler schedule [ schedule-name ] Views Any view Predefined user roles network-admin network-operator Parameters schedule-name: Specifies a schedule by its name, a case-sensitive string of 1 to 47 characters. Without this option, the command displays information about all schedules. Examples # Display information about all schedules.
Field Description Result of the most recent execution: Last execution status • • • • • Successful. Failed. Waiting—The device is executing the schedule and the job is waiting to be executed. In process—The job is being executed. -NA-—The execution time has not arrived yet. To view information about whether the commands in the job has been executed and the execution results, execute the display scheduler logfile command.
Field Remarks Voltage low The voltage is low. Transceiver info I/O error Transceiver information read/write error. Transceiver info checksum error Transceiver information checksum error. Transceiver type and port configuration mismatch The type of the transceiver module does not match the port configuration. Transceiver type not supported by port hardware The port does not support this type of transceiver modules.
Parameters interface [ interface-type interface-number ]: Specifies an interface by its type and number. If no interface is specified, this command displays the current values of the digital diagnosis parameters on every transceiver module. Usage guidelines This command cannot display information about some transceiver modules. Examples # Display the current values of the digital diagnosis parameters on the transceiver module in interface FortyGigE 1/0/1.
network-operator Parameters interface-type interface-number: Specifies an interface by its type and number. Without this option, the command displays the key parameters of every transceiver module. Examples # Display the key parameters of the transceiver module in interface FortyGigE 1/0/1.
Syntax display transceiver manuinfo interface [ interface-type interface-number ] Views Any view Predefined user roles network-admin network-operator Parameters interface [ interface-type interface-number ]: Specifies an interface by its type and number. If no interface is specified, this command displays the electronic label information of the transceiver modules on all interfaces. Usage guidelines This command displays only part of the electronic label information.
display version-update-record Use display version-update-record to display the startup software image upgrade history records of the MPU. (In standalone mode.) Use display version-update-record to display the startup software image upgrade history records of the global active MPU. (In IRF mode.
undo header { legal | login | motd | shell } Default The default settings depend on the device model. Views System view Predefined user roles network-admin Parameters legal: Configures the banner to be displayed before a user inputs the username and password to access the CLI. login: Configures the banner displayed to be before password or scheme authentication is performed for a login user. motd: Configures the greeting banner to be displayed before the legal banner appears.
Welcome to legal (header legal) Press Y or ENTER to continue, N to exit. Welcome to motd(header motd) Welcome to login(header login) Login authentication Password: Welcome to shell(header shell) job Use job to assign a job to a schedule. Use undo job to revoke a job. Syntax job job-name undo job job-name Default No job is assigned to a schedule. Views Schedule view Predefined user roles network-admin Parameters job-name: Specifies the job name, a case-sensitive string of 1 to 47 characters.
memory-threshold Use memory-threshold to set memory alarm thresholds. Use undo memory-threshold to restore the defaults.
For more information about the conditions and rules for generating alarm notifications and alarm-removed notifications, see Fundamentals Configuration Guide. Examples # Set the minor alarm, severe alarm, critical alarm, and normal state thresholds to 64 MB, 48 MB, 32 MB, and 96 MB, respectively. system-view [Sysname] memory-threshold minor 64 severe 48 critical 32 normal 96 monitor cpu-usage enable Use monitor cpu-usage enable to enable CPU usage monitoring.
monitor cpu-usage interval Use monitor cpu-usage interval to configure the interval at which the device samples CPU usage statistics. Syntax In standalone mode: monitor cpu-usage interval interval-value [ slot slot-number ] In IRF mode: monitor cpu-usage interval interval-value [ chassis chassis-number slot slot-number ] Default The sampling interval is 1 minute. Views System view Predefined user roles network-admin Parameters interval-value: Specifies the CPU usage statistics sampling interval.
undo password-recovery enable Default Password recovery capability is enabled. Views System view Predefined user roles network-admin Usage guidelines Password recovery capability controls console user access to the device configuration and SDRAM from BootWare menus. If password recovery capability is enabled, a console user can access the device configuration without authentication to configure new passwords.
force: Reboots the device immediately without performing any software check. If this keyword is not specified, the system checks, for example, whether the main system software image file exists and whether the hard disk is not being written. If any circumstance might affect data protection, the system does not reboot the device. Usage guidelines CAUTION: • Device reboot interrupts network services.
reboot Start to check configuration with next startup configuration file, please wait.........DONE! Current configuration will be lost after the reboot, save current configuration? [Y/N]:n This command will reboot the device. Continue? [Y/N]:y Now rebooting, please wait... # Reboot the device immediately without performing any software check. reboot force This command will reboot the device. Continue? [Y/N]:y Now rebooting, please wait...
Predefined user roles network-admin Examples # Clear job execution log information. reset scheduler logfile Related commands display scheduler logfile reset version-update-record Use reset version-update-record to clear the startup software image upgrade history records of the MPU. (In standalone mode.) Use reset version-update-record to clear the startup software image upgrade history records of the global active MPU. (In IRF mode.
Predefined user roles network-admin Parameters job-name: Specifies the job name, a case-sensitive string of 1 to 47 characters. Usage guidelines A job can be referenced by multiple schedules. In job view, you can assign commands to the job. Examples # Create a job named backupconfig and enter job view.
scheduler reboot at Use scheduler reboot at to specify the reboot date and time. Use undo scheduler reboot to remove the reboot schedule configuration. Syntax scheduler reboot at time [ date ] undo scheduler reboot Default No reboot date or time is specified. Views User view Predefined user roles network-admin Parameters time: Specifies the reboot time in the format hh:mm, where hh is in the range of 0 to 23, and mm is in the range of 0 to 59.
scheduler reboot delay Use scheduler reboot delay to specify the reboot delay time. Use undo scheduler reboot to remove the reboot schedule configuration. Syntax scheduler reboot delay time undo scheduler reboot Default No reboot delay time is specified. Views User view Predefined user roles network-admin Parameters time: Specifies the reboot delay time in the format hh:mm or mm. This argument can consist up to 6 characters. When in the format hh:mm, mm must be in the range of 0 to 59.
Views System view Predefined user roles network-admin Parameters schedule-name: Specifies the schedule name, a case-sensitive string of 1 to 47 characters. Usage guidelines You can schedule a job to have the device automatically run a command or a set of commands without administrative interference. To configure a schedule: 1. Use the scheduler job command to create a job. 2. In job view, use the command command to assign commands to the job. 3.
Predefined user roles network-admin Parameters time: Specifies a detection timer (in seconds) in the range of 1 to 300. Usage guidelines The device starts a detection timer when a port is shut down by a protocol. If the port is still down when the detection timer expires, the device automatically brings up the port so the port status reflects the port's actual physical status.
[R2000] temperature-limit Use temperature-limit to set the temperature alarm thresholds for the device. Use undo temperature-limit to restore the default.
alarmlimit: Specifies the high-temperature alarming threshold in Celsius degrees. The value range depends on the device model. This threshold must be greater than the high-temperature warning threshold.
undo time Default No execution time or date is specified for a schedule. Views Schedule view Predefined user roles network-admin Parameters time: Specifies the schedule execution time in the format hh:mm, where hh is in the range of 0 to 23, and mm is in the range of 0 to 59. date: Specifies the schedule execution date in the format MM/DD/YYYY or YYYY/MM/DD. The YYYY value is in the range of 2000 to 2035, the MM value is in the range of 1 to 12, and the value range for DD depends on the month value.
Parameters at time: Specifies the execution time in the format hh:mm, where hh is in the range of 0 to 23, and mm is in the range of 0 to 59. month-date month-day: Specifies a day in the current month, in the range of 1 to 31. If you specify a day that does not exist in the current month, the configuration takes effect on that day in the next month. week-day week-day&<1-7>: Specifies one or more week days for the schedule. Valid values include Mon, Tue, Wed, Thu, Fri, Sat, and Sun.
Syntax time repeating [ at time [ date ] ] interval interval-time time repeating at time [ month-date [ month-day | last ] | week-day week-day&<1-7> ] undo time Default No execution time table is specified for a schedule. Views Schedule view Predefined user roles network-admin Parameters at time: Specifies the execution time in the format hh:mm, where hh is in the range of 0 to 23, and mm is in the range of 0 to 59.
[Sysname] scheduler schedule saveconfig [Sysname-schedule-saveconfig] time repeating at 12:00 # Configure the device to execute schedule saveconfig at 8:00 a.m. on the 5th of every month. system-view [Sysname] scheduler schedule saveconfig [Sysname-schedule-saveconfig] time repeating at 8:00 month-date 5 # Configure the device to execute schedule saveconfig at 8:00 a.m. on the last day of every month.
For more information about user roles, see the RBAC configuration in Fundamentals Configuration Guide. Examples # Assign user role rolename to schedule test.
Python commands python Use python to enter the Python shell. Syntax python Views User view Predefined user roles network-admin Usage guidelines In the Python shell, you can use the following items: • Python 2.7 commands. • Python 2.7 standard API. • Comware V7 extended API. To return to user view from the Python shell, enter exit(). Examples # Enter the Python shell. python Python 2.7.3 (default, Dec 22 2012, 11:39:05) [GCC 4.4.
Parameters filename: Specifies the name of a Python script on a storage medium (flash memory or USB disk) of the device. The script name is case sensitive and must use the extension .py. The extension .py is case insensitive. param: Specifies the parameters to be passed to the script. To enter multiple parameters, use spaces as the delimiter. Usage guidelines You cannot perform any operation while a Python script is being executed by your command.
Support and other resources Contacting HP For worldwide technical support information, see the HP support website: http://www.hp.
Conventions This section describes the conventions used in this documentation set. Command conventions Convention Description Boldface Bold text represents commands and keywords that you enter literally as shown. Italic Italic text represents arguments that you replace with actual values. [] Square brackets enclose syntax choices (keywords or arguments) that are optional. { x | y | ... } Braces enclose a set of required syntax choices separated by vertical bars, from which you select one.
Network topology icons Represents a generic network device, such as a router, switch, or firewall. Represents a routing-capable device, such as a router or Layer 3 switch. Represents a generic switch, such as a Layer 2 or Layer 3 switch, or a router that supports Layer 2 forwarding and other Layer 2 features. Represents an access controller, a unified wired-WLAN module, or the switching engine on a unified wired-WLAN switch. Represents an access point.
Index ABCDEFGHIJLMNOPQRSTUVW delete,77 A description,46 activation-key,12 dir,77 append,72 dir,109 ascii,72 disconnect,79 authentication-mode,13 display | { begin | exclude | include },2 auto-execute command,14 display | by-linenum,3 B display >,4 backup startup-configuration,127 display >>,5 binary,73 display alarm,154 boot-loader file,139 display boot-loader,145 boot-loader update,141 display clock,155 bootrom backup,142 display command-alias,6 bootrom restore,143 display copyrig
display role feature-group,51 help,82 display saved-configuration,130 history-command max-size,26 display scheduler job,174 hotkey,9 display scheduler logfile,175 I display scheduler reboot,176 idle-timeout,27 display scheduler schedule,176 interface policy deny,53 display startup,130 display telnet client,19 J display this,132 job,185 display transceiver alarm,178 L display transceiver diagnosis,179 lcd,83 display transceiver interface,180 line,28 display transceiver manuinfo,181 lin
stopbits,37 quit,9 quit,89 Subscription service,207 R super,62 super authentication-mode,63 reboot,189 super password,64 reget,89 sysname,197 rename,90 system,97 rename,120 system-view,11 reset,91 reset recycle-bin,120 T reset saved-configuration,133 tar create,122 reset scheduler logfile,191 tar extract,123 reset version-update-record,192 tar list,124 restart,91 telnet,37 restore startup-configuration,134 telnet client source,38 return,10 telnet server acl,39 rhelp,92 telnet ser
