® HP 9000 HSC Systems J2468A, J3573A, J2469A & J2499A HP-HSC ATM/622 & ATM/155 Adapters Hardware Installation Guide
J2468A, J3573A, J2469A & J2499A HP-HSC ATM/622 & ATM/155 Adapters Hardware Installation Guide Edition E0198 Customer order number 5966-8702 HP manufacturing part number 5966-8702
Copyright and trademark information This document contains proprietary information which is protected by copyright. All rights reserved. No part of this document may be photocopied, reproduced or translated into another language without the prior written consent of Hewlett-Packard company. © Hewlett-Packard Company, 1998. All rights reserved. UNIX is a registered trademark in the United States and other countries, licensed exclusively through X/Open Company Limited.
Contents 1 Before you install the ATM adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Check that you have received the following items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Check that your configuration is supported . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Check the computer requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents 6
1 Before you install the ATM adapter Check that you have received the following items • • • • • the ATM Adapter ATM software on CD-ROM the Codeword to Install Software Certificate to unlock the J2806CA product ATM/622 & ATM/155 Adapters Configuration and Troubleshooting Guide the appropriate Release Notes for your product Check that your configuration is supported Consult the Release Notes you received with the ATM software for a list of the HP 9000 systems supported, together with information about the
1 Check that you have the necessary addresses Check that you have the necessary addresses • For all installations you need the ATM adapter’s IP address. • For installations where the local network uses subnets you need the subnet mask of the local network. • For installations where you intend to use LAN emulation you need: • an IP address for each emulated LAN • the IP address of the LECS (LAN emulation configuration server) • For installations where you are connecting to a non-UNI 3.
Check you have the correct cables Check you have the correct cables Note Product description Cable suppliers include SC to SC cable SC to ST cable (duplex adapter) SC loopback connector AMP, Amphenol Socapex, 3M UTP Cat 5 direct cable (1.5 m) UTP Cat 5 direct cable (3.0 m) UTP Cat 5 direct cable (7.6 m) HP, INMAC, BLACK BOX, AMP Ensure that you have the correct quality (SMF, MMF or UTP Cat5) of cable or loopback connector for your adapter. • Multi Mode Fibre.
1 ATM adapter specifications ATM adapter specifications Power consumption These ATM adapters are powered from the HSC connector and have the following maximum power consumption requirements: Adapter Power Consumption 3.3 V 5V 12 V J2468A & J3573A 3.7 W 15.8 W 0W J2469A & J2499A 2.2 W 9W 2W Environmental specifications Temperature Operating: 0 to 55˚C with 1 m/s of air flow Non-operating: -20 to 70˚C Humidity Operating: 15 to 95% at 40˚C Altitude Operating: 4600 m (15000 ft.
2 Installing the ATM hardware HP 9000 B, C, D and J-Class systems WARNING Electric shock hazard. Switch off the system, disconnect the power cable and all telecommunications network cables before opening the system or accessing the slots. Cleaning precautions Hewlett-Packard strongly recommends that you keep the fiber optic cable plugs clean by always covering the ends of the cable with the protective dust caps when the cables are not connected to the ATM adapter.
2 HP 9000 B, C, D and J-Class systems 5 Install the ATM adapter in your system, referring to the system documentation for installation instructions: • • • Note Class B: “Owner’s Guide” Class C and J: “Owner’s Guide” Class D: “I/O Card Upgrade Guide” If you have problems when installing the UTP Cat5 J2499A ATM adapter, Hewlett-Packard recommends that you remove the cards in the adjacent slots, install the ATM adapter and then reinstall the other cards.
HP 9000 B, C, D and J-Class systems Summary of LED behavior Rx LED Tx LED Successful hardware installation, cable not connected or incorrectly connected Yellow Off Successful hardware installation and cables corrected connected Off Off Data transmission on the ATM adapter Green Green Installing the ATM software The hardware installation is now complete. You are now ready to install the software as described in the Configuration and Troubleshooting Guide.
2 HP 9000 K-Class systems HP 9000 K-Class systems WARNING Electric shock hazard. Switch off the system, disconnect the power cable and all telecommunications network cables before opening the system or accessing the slots. Cleaning precautions Hewlett-Packard strongly recommends that you keep the fiber optic cable plugs clean by always covering the ends of the cable with the protective dust caps when the cables are not connected to the ATM adapter.
HP 9000 K-Class systems 6 Unscrew the two retaining screws of the host board. 7 Remove the host board from the system. 8 Put the two hooks on the face plate of the ATM adapter into the slots on the face plate of the host board and press the connector firmly into the socket on the host board. ➁ ➀ 9 Screw the two face plates together. 10 CAREFULLY and SLOWLY replace the host board in the system. 11 Fasten the host board in place using the two retaining hooks, and replace the two screws.
2 HP 9000 K-Class systems 12 If you are connecting to an ATM switch, consult your switch documentation. 13 To connect the ATM adapter to an ATM switch, or back-to-back with another ATM adapter, you must: Note • Connect the ATM cable to the ATM adapter and to a free port on other device in such a way that the cables are “crossed over” so that the transmit of one device connects to the receive of the other device. With UTP Cat 5 cables, you must use a cross-over cable.
HP 9000 K-Class systems Summary of LED behavior Rx LED Tx LED Successful hardware installation, cable not connected or incorrectly connected Yellow Off Successful hardware installation and cables corrected connected Off Off Data transmission on the ATM adapter Green Green Installing the ATM software The hardware installation is now complete. You are now ready to install the software as described in the Configuration and Troubleshooting Guide.
2 HP 9000 T-Class Corporate Business Server, Model T600 HP 9000 T-Class Corporate Business Server, Model T600 Note Only qualified Hewlett-Packard personnel can install ATM adapters in the HP 9000 T-Class Corporate Business Server, Model T600. Cleaning precautions Hewlett-Packard strongly recommends that you keep the fiber optic cable plugs clean by always covering the ends of the cable with the protective dust caps when the cables are not connected to the ATM adapter.
HP 9000 T-Class Corporate Business Server, Model T600 3 Choose the slot you are going to use for each ATM adapter.
2 HP 9000 T-Class Corporate Business Server, Model T600 7 To connect the ATM adapter to an ATM switch or back-to-back with another ATM adapter you must: Note • Connect the ATM cable to the ATM adapter and to a free port on other device in such a way that the cables are “crossed over” so that the transmit of one device connects to the receive of the other device. With UTP Cat 5 cables, you must use a cross-over cable. See the Configuration and Troubleshooting Guide.
HP 9000 T-Class Corporate Business Server, Model T600 Summary of LED behavior Rx LED Tx LED Successful hardware installation, cable not connected or incorrectly connected Yellow Off Successful hardware installation and cables corrected connected Off Off Data transmission on the ATM adapter Green Green Installing the ATM software The hardware installation is now complete. You are now ready to install the software as described in the Configuration and Troubleshooting Guide.
2 HP 9000 T-Class Corporate Business Server, Model T600 22
Regulatory information, cautions and warnings Safety information Regulatory information Warning Optic module All inputs/outputs are Safety Extra Low Voltage (SELV) circuits. The optic module provided in the HP J2468A, J3573A, J2469A, and J2499A ATM adapters conforms to the ITU-T recommendation G.957 cat I-1 or I-4. Warning For the United States Electrical Shock Hazard. Do not remove system covers.
Regulatory information, cautions and warnings For Europe This is a Class A product. In a domestic environment this product may cause radio interference, in which case the user may be required to take adequate measures. For Canada Canadian regulations ICES-003 Complies with Canadian Electromagnetic compatibility (EMC) Class A requirements. Conforme à la Classe A des normes Canadiennes de compatibilité éléctromagnetique (CEM).
Regulatory information, cautions and warnings DECLARATION OF CONFORMITY according to ISO/IEC Guide 22 and EN 45014 Manufacturer’s name: Manufacturer’s address: Hewlett-Packard 5 Raymond Chanas - Eybens 38053 Grenoble Cedex 09 France Declares that the products: Product Name: Product Number HP-HSC ATM/622 Adapter HP-HSC ATM/155 Adapter HP-HSC ATM/155 Adapter HP-HSC ATM/622 Adapter J2468A J2469A J2499A J3573A Conform to the following product specifications: SAFETY: EMC: IEC 950: 1991 + A1 +A2 +A3 / EN
® Printed in Europe - E0198 Order Number 5966-8702 Manufacturing Part Number
