HP X.25/9000 Release Notes HP-UX 11i v1 Manufacturing Part Number: J2793-90070 September 2008 © Copyright 2008 Hewlett-Packard Development Company, L.P.
Legal Notices Copyright 2008 Hewlett-Packard Development Company, L.P. Confidential computer software. Valid license required from HP for po session, use or copying. Consistent with FAR 12.211 and 12.212, Commercial Computer Software, Computer Software Documentation, and Technical Data for Commercial Items are licensed to the U.S. Government under vendor’s standard commercial license. The information contained herein is subject to change without notice.
1 HP X.25 Release Notes The information in this document applies to the release of X.25 version B.11.11.02 for HP-UX 11i v1.
HP X.25 Release Notes What Is in This Version What Is in This Version This release of X.25 includes only defect fixes and does not contain any new feature. For information on the defect fixes included in this version of X.25, see “Defect Fixes in This Version” on page 11.
HP X.25 Release Notes Known Problems and Workarounds Known Problems and Workarounds This section describes known problems and workarounds for version B.11.11.02 of the J2793B X.25 product. • Coexistence between the X.25 PSI cards and the ACC (Advanced Communication Controller) cards on the same system is not supported. You can use PSI cards supported by the J2793B product or ACC cards supported by the Z7476AA product, but do not install both cards on the same system. If the X.
HP X.25 Release Notes Known Problems and Workarounds Table 1-1 • Recommended Window Sizes (Continued) Level 3 Packet Size Level 2 Window Size 128 1 - 127 64 1 - 127 32 1 - 127 16 1 - 127 nettl sequence numbering in traces may be incorrect with modulo-128. Workaround. You may disregard the sequence numbering information, or use strace to see Level 3 packet sequence numbers.
HP X.25 Release Notes Known Problems and Workarounds • When configuring the J3525 card using SAM the following error message maybe seen on the SAM screen: Configuration information has been downloaded to x25_0p1. With out connection to the network, the x25card cannot be enabled. The above error message can be ignored if the SAM screen indicates that the card is enabled.
HP X.25 Release Notes Compatibility Information and Installation Requirements Compatibility Information and Installation Requirements The following section lists the hardware and software requirements for the J2793B X.25 product. Installation Requirements Version B.11.11.02 of J2793B requires the HP-UX 11i software to be installed and correctly configured. To use the OLAR feature, your system must be running HP-UX 11i.
HP X.25 Release Notes Compatibility Information and Installation Requirements Table 1-2 Supported Adapters (Continued) Supported Adapters Number of Ports J3526A Table 1-3 Adapters HP-UX 11i OS Bus Type 4 PCI 32- or 64-bit Supported Interfaces RS-232 V.35/V.36 X.21 RS-449 RS-530 J2792A 64 Kbps 64 Kbps 256 Kbps 256 Kbps NA J2794A 64 Kbps 64 Kbps NA 1.
HP X.
HP X.25 Release Notes Defect Fixes in This Version Defect Fixes in This Version The following defect fix is included in this version: QXCR1000819808 J2793B 11.11.01 0706 Bundle :Filesets in SYNC-WAN product are of incorrect version. NOTE Chapter 1 The defects fixed in X.25 version 11.11.01 are also applicable to this version of X.25.11.11.02.
HP X.25 Release Notes Software Availability in Native Languages Software Availability in Native Languages This version of the J2793B software is available only in English. Also, the documentation for version B.11.11.02 of the J2793B X.25 software is available only in English. However, Appendix A of the X.25/9000 User's Guide provides instructions for using French, Italian and German Subscription forms when configuring the X.25 software.
