R3102-R3103-HP 6600/HSR6600 Routers High Availability Configuration Guide

137
[RouterC] cfd service-instance 1 md MD ma MA_A
# Create a MEP list in service instance 1. Create and enable outward-facing MEP 1001, and
enable CCM sending in service instance 1 on GigabitEthernet 3/0/1.
[RouterC] cfd meplist 1001 1002 service-instance 1
[RouterC] interface gigabitethernet 3/0/1
[RouterC-GigabitEthernet3/0/1] cfd mep 1001 service-instance 1 outbound
[RouterC-GigabitEthernet3/0/1] cfd mep service-instance 1 mep 1001 enable
[RouterC-GigabitEthernet3/0/1] cfd cc service-instance 1 mep 1001 enable
[RouterC-GigabitEthernet3/0/1] quit
# Create MA MA_B for the MD and configure the MA to serve VLAN 110. Create service
instance 2 for the MD and MA.
[RouterC] cfd ma MA_B md MD vlan 110
[RouterC] cfd service-instance 2 md MD ma MA_B
# Create a MEP list in service instance 2. Create and enable outward-facing MEP 2001. Enable
CCM sending in service instance 2 on GigabitEthernet 3/0/2.
[RouterC] cfd meplist 2001 2002 service-instance 2
[RouterC] interface gigabitethernet 3/0/2
[RouterC-GigabitEthernet3/0/2] cfd mep 2001 service-instance 2 outbound
[RouterC-GigabitEthernet3/0/2] cfd mep service-instance 2 mep 2001 enable
[RouterC-GigabitEthernet3/0/2] cfd cc service-instance 2 mep 2001 enable
[RouterC-GigabitEthernet3/0/2] quit
# Configure the collaboration between the primary port GigabitEthernet 3/0/1 of smart link
group 1 and the CC function of CFD, and bring up the port.
[RouterC] interface gigabitethernet 3/0/1
[RouterC-GigabitEthernet3/0/1] port smart-link group 1 track cfd cc
[RouterC-GigabitEthernet3/0/1] undo shutdown
[RouterC-GigabitEthernet3/0/1] quit
# Configure the collaboration between the primary port GigabitEthernet 3/0/2 of smart link
group 2 and the CC function of CFD, and bring up the port.
[RouterC] interface gigabitethernet 3/0/2
[RouterC-GigabitEthernet3/0/2] port smart-link group 2 track cfd cc
[RouterC-GigabitEthernet3/0/2] undo shutdown
[RouterC-GigabitEthernet3/0/2] quit
4. Configure Router D:
# Create VLAN 1 through VLAN 200.
<RouterD> system-view
[RouterD] vlan 1 to 200
# Configure GigabitEthernet 3/0/1 as a trunk port and assign it to VLANs 1 through 200.
Enable flush message receiving and configure VLAN 10 and VLAN 110 as the receive control
VLANs on GigabitEthernet 3/0/1.
[RouterD] interface gigabitethernet 3/0/1
[RouterD-GigabitEthernet3/0/1] port link-type trunk
[RouterD-GigabitEthernet3/0/1] port trunk permit vlan 1 to 200
[RouterD-GigabitEthernet3/0/1] smart-link flush enable control-vlan 10 110
[RouterD-GigabitEthernet3/0/1] quit