R3102-R3103-HP 6600/HSR6600 Routers High Availability Configuration Guide

192
Configuration procedure
1. Configure Router A:
<RouterA> system-view
[RouterA] ipv6
[RouterA] interface gigabitethernet 1/0/1
[RouterA-GigabitEthernet1/0/1] ipv6 address fe80::1 link-local
[RouterA-GigabitEthernet1/0/1] ipv6 address 1::1 64
# Create VRRP group 1 and set its virtual IPv6 addresses to FE80::10 and 1::10.
[RouterA-GigabitEthernet1/0/1] vrrp ipv6 vrid 1 virtual-ip fe80::10 link-local
[RouterA-GigabitEthernet1/0/1] vrrp ipv6 vrid 1 virtual-ip 1::10
# Set the priority of Router A in VRRP group 1 to 110, which is higher than that of Router B
(100), so that Router A can become the master in VRRP group 1.
[RouterA-GigabitEthernet1/0/1] vrrp ipv6 vrid 1 priority 110
# Create VRRP group 2 set its virtual IPv6 addresses to FE80::20 and 1::20.
[RouterA-GigabitEthernet1/0/1] vrrp ipv6 vrid 2 virtual-ip fe80::20 link-local
[RouterA-GigabitEthernet1/0/1] vrrp ipv6 vrid 2 virtual-ip 1::20
2. Configure Router B:
<RouterB> system-view
[RouterB] ipv6
[RouterB] interface gigabitethernet 1/0/1
[RouterB-GigabitEthernet1/0/1] ipv6 address fe80::2 link-local
[RouterB-GigabitEthernet1/0/1] ipv6 address 1::2 64
# Create VRRP group 1 and set its virtual IPv6 addresses to FE80::10 and 1::10.
[RouterB-GigabitEthernet1/0/1] vrrp ipv6 vrid 1 virtual-ip fe80::10 link-local
[RouterB-GigabitEthernet1/0/1] vrrp ipv6 vrid 1 virtual-ip 1::10
# Create VRRP group 2 set its virtual IPv6 addresses to FE80::20 and 1::20.
[RouterB-GigabitEthernet1/0/1] vrrp ipv6 vrid 2 virtual-ip fe80::20 link-local
[RouterB-GigabitEthernet1/0/1] vrrp ipv6 vrid 2 virtual-ip 1::20
# Set the priority of Router B in VRRP group 2 to 110, which is higher than that of Router A
(100), so that Router B can become the master in VRRP group 2.
[RouterB-GigabitEthernet1/0/1] vrrp ipv6 vrid 2 priority 110
3. Verify the configuration:
To verify your configuration, use the display vrrp ipv6 verbose command.
# Display the detailed information about the VRRP group on Router A.
[RouterA] display vrrp ipv6 verbose
IPv6 Standby Information:
Run Mode : Standard
Run Method : Virtual MAC
Total number of virtual routers : 2
Interface GigabitEthernet1/0/1
VRID : 1 Adver Timer : 100
Admin Status : Up State : Master
Config Pri : 110 Running Pri : 110
Preempt Mode : Yes Delay Time : 0
Auth Type : None
Virtual IP : FE80::10