R3102-R3103-HP 6600/HSR6600 Routers High Availability Configuration Guide

135
[RouterA-GigabitEthernet3/0/1] cfd mep 1002 service-instance 1 outbound
[RouterA-GigabitEthernet3/0/1] cfd mep service-instance 1 mep 1002 enable
[RouterA-GigabitEthernet3/0/1] cfd cc service-instance 1 mep 1002 enable
[RouterA-GigabitEthernet3/0/1] quit
# Create MA MA_B for the MD and configure the MA to serve VLAN 110. Create service
instance 2 for the MD and MA.
[RouterA] cfd ma MA_B md MD vlan 110
[RouterA] cfd service-instance 2 md MD ma MA_B
# Create a MEP list in service instance 2, create and enable outward-facing MEP 1002, and
enable CCM sending in service instance 2 on GigabitEthernet 3/0/2.
[RouterA] cfd meplist 2001 2002 service-instance 2
[RouterA] interface gigabitethernet 3/0/2
[RouterA-GigabitEthernet3/0/2] cfd mep 2002 service-instance 2 outbound
[RouterA-GigabitEthernet3/0/2] cfd mep service-instance 2 mep 2002 enable
[RouterA-GigabitEthernet3/0/2] cfd cc service-instance 2 mep 2002 enable
[RouterA-GigabitEthernet3/0/2] quit
2. Configure Router B:
# Create VLAN 1 through VLAN 200.
<RouterB> system-view
[RouterB] vlan 1 to 200
# Configure GigabitEthernet 3/0/1 as a trunk port and assign it to VLANs 1 through 200.
Enable flush message receiving and configure VLAN 10 and VLAN 110 as the receive control
VLANs on GigabitEthernet 3/0/1.
[RouterB] interface gigabitethernet 3/0/1
[RouterB-GigabitEthernet3/0/1] port link-type trunk
[RouterB-GigabitEthernet3/0/1] port trunk permit vlan 1 to 200
[RouterB-GigabitEthernet3/0/1] smart-link flush enable control-vlan 10 110
[RouterB-GigabitEthernet3/0/1] quit
# Configure GigabitEthernet 3/0/2 as a trunk port and assign it to VLANs 1 through 200.
Disable the spanning tree feature and enable flush message receiving on it. Configure VLAN 10
and VLAN 110 as the receive control VLANs.
[RouterB] interface gigabitethernet 3/0/2
[RouterB-GigabitEthernet3/0/2] port link-type trunk
[RouterB-GigabitEthernet3/0/2] port trunk permit vlan 1 to 200
[RouterB-GigabitEthernet3/0/2] undo stp enable
[RouterB-GigabitEthernet3/0/2] smart-link flush enable control-vlan 10 110
[RouterB-GigabitEthernet3/0/2] quit
3. Configure Router C:
# Create VLAN 1 through VLAN 200, map VLANs 1 through 100 to MSTI 1 and VLANs 101
through 200 to MSTI 2, and activate MST region configuration.
<RouterC> system-view
[RouterC] vlan 1 to 200
[RouterC] stp region-configuration
[RouterC-mst-region] instance 1 vlan 1 to 100
[RouterC-mst-region] instance 2 vlan 101 to 200
[RouterC-mst-region] active region-configuration
[RouterC-mst-region] quit