HP Comware 5 Debug Manual Vol 2

// The LNS address in Radius is 100.1.1.2.
*0.3139156 lac L2TP/7/L2TDBG: L2TP::VPDN Group Number in Radius = 1
// The VPDN group number in Radius is 1.
*0.3139156 lac L2TP/7/L2TDBG: L2TP::LNS Address = 100.1.1.2
// The LNS address is 100.1.1.2.
*0.3139156 lac L2TP/7/L2TDBG: L2TP::Add New Call 27585 to Tunnel 1 call list(total 1)
// L2TP added new call 27585 to the call list of Tunnel 1.
*0.3139156 lac L2TP/7/L2TDBG: L2TP::Get udp port successfully : port 1701
// L2TP got UDP port 1701 successfully.
*0.3139172 lac L2TP/7/L2TDBG: L2TP::Receive message with message type: 2
// L2TP received a message with message type 2.
*0.3139172 lac L2TP/7/L2TDBG: L2TP::Board 0 recv from SOCK CallID=0 TunnelID=1 MsgType
= 2 Length = 117
// Board 0 received a call with the ID 0, tunnel ID 1, message type 2 and length 117.
# Enable debugging for hidden AVP. Output similar to the following example is generated when the
following conditions exist:
•
Two devices act as LAC and LNS.
•
L2TP is enabled on the two devices.
•
Hidden AVP is configured on the LAC side.
<Sysname> debugging l2tp hidden
*0.423360 lac L2TP/7/L2TDBG:
First digest when build hidden avp. 50 ffffffdb b 5c 35 ffffffe9 ffffff 8a 3f
25 41 7b 3d 6c 1 6c ffffffc5
*0.423360 lac L2TP/7/L2TDBG:
// The output above shows the first digest when L2TP is building hidden AVP.
Hidden AVP value put . 50 ffffffc8 67 6e 41 ffffff99 ffffffff 4c 40 33 3b 55 19
60 1b ffffffa0 ffffff93 ffffffde a 49 ffffffe2 60 43 ffffffb3
7c ffffffc4 1f ffffffc0 ffffff86 ffffffeb ffffff84 40
// The output above shows the hidden AVP value.
*0.425344 lac L2TP/7/L2TDBG: First digest when build hidden avp.ffffffe1 13 ffffffe3
ffffffe2 ffffffcb ffffffe4 3e ffffffc7 ffffffab 19 ffffffab 2b 6d 70 ffffff82
ffffffbf
// The output above shows the first digest when L2TP is building hidden AVP.
*0.425344 lac L2TP/7/L2TDBG:Hidden AVP value put .ffffffe1 19 ffffff96 ffffff91 ffffffae
ffffff96 56 ffff
ffb2 ffffffca 6e ffffffce 42 6d 70 ffffff82 ffffffbf 0 0 0 0 0 00 0 0
0 0 0 0 0 0 0
// The output above shows the hidden AVP value.
# Enable debugging for L2TP data packets. Output similar to the following example is generated when
the following conditions exist:
•
Two devices act as LAC and LNS.
•
L2TP is enabled on the two devices.
•
PAP and flow control are configured on the two devices.
303