Manualshelf

HP Comware 5 Debug Manual Vol 3

ManualsBrandsHP ManualsNetwork HardwareHP HSR6804 Router Chassis
291292293294295296297298299300
*Nov 24 15:57:46:32 2006 Sysname RM/6/RMDEBUG: AFI 2, dest 50.0.0.2/255.255.255.255,
nexthop 0.0.0.0, cost 1, tag 0
// The first route entry was output.
*Nov 24 15:57:46:32 2006 Sysname RM/6/RMDEBUG: AFI 2, dest 50.0.0.0/255.0.0.0, nexthop
0.0.0.0, cost 1, tag 0
// The second route entry was output.
*Nov 24 15:57:46:32 2006 Sysname RM/6/RMDEBUG: AFI 2, dest 110.0.0.1/255.255.255.255,
nexthop 0.0.0.0, cost 1, tag 0
// The third route entry was output.
*Nov 24 15:57:46:32 2006 Sysname RM/6/RMDEBUG: RIP 1 : Receive response from 40.0.0.1 on
Ethernet1/1
// RIP process 1 received a response packet from 40.0.0.1 on Ethernet 1/1.
*Nov 24 15:57:46:32 2006 Sysname RM/6/RMDEBUG: Packet : vers 2, cmd response, length
84
// The version of the received response packet is 2 and the packet length is 84 bytes.
*Nov 24 15:57:46:32 2006 Sysname RM/6/RMDEBUG: AFI 2, dest 50.0.0.1/255.255.255.255,
nexthop 0.0.0.0, cost 1, tag 0
// The first route entry was output.
*Nov 24 15:57:46:32 2006 Sysname RM/6/RMDEBUG: AFI 2, dest 50.0.0.0/255.0.0.0, nexthop
0.0.0.0, cost 1, tag 0
// The second route entry was output.
*Nov 24 15:57:46:86 2006 Sysname RM/6/RMDEBUG: AFI 2, dest 100.0.0.1/255.255.255.255,
nexthop 0.0.0.0, cost 1, tag 0
// The third route entry was output.
*Nov 24 15:57:46:86 2006 Sysname RM/6/RMDEBUG: AFI 2, dest 110.0.0.1/255.255.255.255,
nexthop 0.0.0.0, cost 16, tag 0
// The fourth route entry was output.
*Nov 24 15:57:46:102 2006 Sysname RM/3/RMDEBUG: RIP 1 : Ignoring this packet.
Authentication validation failed.
// Authentication failed. The received response packet was ignored.
# Clear the packet debugging information of the specified process, so no related debugging information
is displayed.
<Sysname> reset rip 1 process
Warning : Reset RIP process? [Y/N]:y
# Enable packet debugging if you want to view packet debugging information on Router A after the reset
operation.
<Sysname> debugging rip 1 packet
# Enable RIP packet debugging on Router A. The output in this example was created when the following
conditions exist:
•
Serial 2/0 of Router A is connected to Serial 2/0 of Router B.
•
RIP is enabled on Router A and Router B.
<Sysname> debugging rip 1 packet
*Nov 24 15:45:45:522 2006 Sysname RM/6/RMDEBUG: TRIP 1 : Sending request on interface
Serial2/0 to 224.0.0.9
// TRIP process 1 sent a request packet on Serial2/0 to 224.0.0.9.
292