R3303-HP HSR6800 Routers IP Multicast Configuration Guide
155
Device Interface IP address
Device
Interface
IP address
Router A GE2/1/0 192.168.1.1/24 Router D GE2/1/1 10.110.4.2/24
GE2/1/1 10.110.1.1
/
24
GE2/1/3 10.110.7.1
/
24
Router B GE2/1/0 192.168.2.1/24
GE2/1/2 10.110.8.1
/
24
GE2/1/1 10.110.1.2/24 Router E GE2/1/0 192.168.4.1/24
GE2/1/2 10.110.2.1
/
24
GE2/1/1 10.110.5.2
/
24
GE2/1/4 10.110.3.1
/
24
GE2/1/3 10.110.7.2
/
24
Router C GE2/1/0 192.168.3.1/24 Router F GE2/1/1 10.110.9.1/24
GE2/1/1 10.110.4.1
/
24
GE2/1/2 10.110.8.2
/
24
GE2/1/3 10.110.5.1
/
24
GE2/1/4 10.110.3.2
/
24
GE2/1/2 10.110.2.2/24 Router G GE2/1/0 192.168.5.1/24
GE2/1/4 10.110.6.1
/
24
GE2/1/1 10.110.9.2
/
24
Router H GE2/1/1 10.110.10.1
/
24
Source 1
—
192.168.2.10/24
GE2/1/2 10.110.6.2/24 Source 2 — 192.168.3.10/24
Router I GE2/1/0 192.168.6.1/24
Source 3
—
192.168.5.10/24
GE2/1/1 10.110.10.2
/
24
Configuration procedure
1. Assign an IP address and subnet mask to each interface according to Figure 47. (Details not
shown.)
2. Configure OSPF on the routers in the PIM-SM domain to make sure they are interoperable at the
network layer. (Details not shown.)
3. Enable IP multicast routing, administrative scoping, PIM-SM, and IGMP:
# Enable IP multicast routing and administrative scoping on Router A, enable PIM-SM on each
interface, and enable IGMP on the host-side interface GigabitEthernet 2/1/0.
<RouterA> system-view
[RouterA] multicast routing-enable
[RouterA] pim
[RouterA-pim] c-bsr admin-scope
[RouterA-pim] quit
[RouterA] interface gigabitethernet 2/1/0
[RouterA-GigabitEthernet2/1/0] igmp enable
[RouterA-GigabitEthernet2/1/0] pim sm
[RouterA-GigabitEthernet2/1/0] quit
[RouterA] interface gigabitethernet 2/1/1
[RouterA-GigabitEthernet2/1/1] pim sm
[RouterA-GigabitEthernet2/1/1] quit
# Enable IP multicast routing, administrative scoping, PIM-SM, and IGMP on Router E and Router
I in the same way. (Details not shown.)
# On Router B, enable IP multicast routing and administrative scoping, and enable PIM-SM on
each interface.
<RouterB> system-view
[RouterB] multicast routing-enable
[RouterB] pim
[RouterB-pim] c-bsr admin-scope
[RouterB-pim] quit