R3303-HP HSR6800 Routers MPLS Configuration Guide

327
[Spoke-PE2-LoopBack0] quit
[Spoke-PE2] interface pos 5/1/1
[Spoke-PE2-POS5/1/1] ip address 172.2.1.1 24
[Spoke-PE2-POS5/1/1] quit
[Spoke-PE2] ospf
[Spoke-PE2-ospf-1] area 0
[Spoke-PE2-ospf-1-area-0.0.0.0] network 172.2.1.0 0.0.0.255
[Spoke-PE2-ospf-1-area-0.0.0.0] network 3.3.3.9 0.0.0.0
[Spoke-PE2-ospf-1-area-0.0.0.0] quit
[Spoke-PE2-ospf-1] quit
# Configure the Hub-PE.
<Hub-PE> system-view
[Hub-PE] interface loopback 0
[Hub-PE-LoopBack0] ip address 2.2.2.9 32
[Hub-PE-LoopBack0] quit
[Hub-PE] interface pos 5/1/1
[Hub-PE-POS5/1/1] ip address 172.1.1.2 24
[Hub-PE-POS5/1/1] quit
[Hub-PE] interface pos 5/1/2/2
[Hub-PE-POS5/1/2] ip address 172.2.1.2 24
[Hub-PE-POS5/1/2] quit
[Hub-PE] ospf
[Hub-PE-ospf-1] area 0
[Hub-PE-ospf-1-area-0.0.0.0] network 172.1.1.0 0.0.0.255
[Hub-PE-ospf-1-area-0.0.0.0] network 172.2.1.0 0.0.0.255
[Hub-PE-ospf-1-area-0.0.0.0] network 2.2.2.9 0.0.0.0
[Hub-PE-ospf-1-area-0.0.0.0] quit
[Hub-PE-ospf-1] quit
After the configuration, OSPF adjacencies are established between Spoke-PE 1 and Hub-PE, and
between Spoke-PE 2 and Hub-PE. Execute the display ospf peer command. The output shows that
the adjacency status is Full. Execute the display ip routing-table command. The output shows that
the PEs have learned the routes to the loopback interfaces of each other.
Take Spoke-PE 1 as an example:
[Spoke-PE1] display ip routing-table
Routing Tables: Public
Destinations : 10 Routes : 10
Destination/Mask Proto Pre Cost NextHop Interface
1.1.1.9/32 Direct 0 0 127.0.0.1 InLoop0
2.2.2.9/32 OSPF 10 1 172.1.1.2 POS5/1/1
3.3.3.9/32 OSPF 10 2 172.1.1.2 POS5/1/1
10.1.1.0/24 Direct 0 0 10.1.1.2 GE2/1/1
10.1.1.2/32 Direct 0 0 127.0.0.1 InLoop0
127.0.0.0/8 Direct 0 0 127.0.0.1 InLoop0
127.0.0.1/32 Direct 0 0 127.0.0.1 InLoop0
172.1.1.0/24 Direct 0 0 172.1.1.1 POS5/1/1
172.1.1.1/32 Direct 0 0 127.0.0.1 InLoop0