R3303-HP HSR6800 Routers High Availability Configuration Guide

ManualsBrandsHP ManualsNetwork HardwareHP HSR68xx Configure-to-Order Router Solution

100

[RouterB-rrpp-domain1] ring 2 node-mode edge edge-port gigabitethernet 3/0/3

[RouterB-rrpp-domain1] ring 2 enable

[RouterB-rrpp-domain1] quit

# Enable RRPP.

[RouterB] rrpp enable

3. Configure Router C:

# Create VLANs 1 through 30, map these VLANs to MSTI 1, and activate the MST region

configuration.

<RouterC> system-view

[RouterC] vlan 1 to 30

[RouterC] stp region-configuration

[RouterC-mst-region] instance 1 vlan 1 to 30

[RouterC-mst-region] active region-configuration

[RouterC-mst-region] quit

# Set the physical state change suppression interval to 0 seconds on GigabitEthernet 3/0/1,

GigabitEthernet 3/0/2, and GigabitEthernet 3/0/3. Disable the spanning tree feature, configure

the ports as trunk ports, and assign them to VLANs 1 through 30.

[RouterC] interface gigabitethernet 3/0/1

[RouterC-GigabitEthernet3/0/1] link-delay 0

[RouterC-GigabitEthernet3/0/1] undo stp enable

[RouterC-GigabitEthernet3/0/1] port link-type trunk

[RouterC-GigabitEthernet3/0/1] port trunk permit vlan 1 to 30

[RouterC-GigabitEthernet3/0/1] quit

[RouterC] interface gigabitethernet 3/0/2

[RouterC-GigabitEthernet3/0/2] link-delay 0

[RouterC-GigabitEthernet3/0/2] undo stp enable

[RouterC-GigabitEthernet3/0/2] port link-type trunk

[RouterC-GigabitEthernet3/0/2] port trunk permit vlan 1 to 30

[RouterC-GigabitEthernet3/0/2] quit

[RouterC] interface gigabitethernet 3/0/3

[RouterC-GigabitEthernet3/0/3] link-delay 0

[RouterC-GigabitEthernet3/0/3] undo stp enable

[RouterC-GigabitEthernet3/0/3] port link-type trunk

[RouterC-GigabitEthernet3/0/3] port trunk permit vlan 1 to 30

[RouterC-GigabitEthernet3/0/3] quit

# Create RRPP domain 1, configure VLAN 4092 as the primary control VLAN of RRPP domain 1,

and configure VLANs mapped to MSTI 1 as the protected VLANs of RRPP domain 1.

[RouterC] rrpp domain 1

[RouterC-rrpp-domain1] control-vlan 4092

[RouterC-rrpp-domain1] protected-vlan reference-instance 1

# Configure Router C as a transit node of primary ring 1, with GigabitEthernet 3/0/1 as the

primary port and GigabitEthernet 3/0/2 as the secondary port, and enable ring 1.

[RouterC-rrpp-domain1] ring 1 node-mode transit primary-port gigabitethernet 3/0/1

secondary-port gigabitethernet 3/0/2 level 0

[RouterC-rrpp-domain1] ring 1 enable

# Configure Router C as the assistant-edge node of subring 2, with GigabitEthernet 3/0/3 as the

edge port, and enable ring 2.