R3303-HP HSR6800 Routers High Availability Configuration Guide

101
[RouterD-GigabitEthernet3/0/3] link-delay 0
[RouterD-GigabitEthernet3/0/3] undo stp enable
[RouterD-GigabitEthernet3/0/3] port link-type trunk
[RouterD-GigabitEthernet3/0/3] port trunk permit vlan 1 to 30
[RouterD-GigabitEthernet3/0/3] quit
[RouterD] interface gigabitethernet 3/0/4
[RouterD-GigabitEthernet3/0/4] link-delay 0
[RouterD-GigabitEthernet3/0/4] undo stp enable
[RouterD-GigabitEthernet3/0/4] port link-type trunk
[RouterD-GigabitEthernet3/0/4] port trunk permit vlan 1 to 30
[RouterD-GigabitEthernet3/0/4] quit
# Create RRPP domain 1, configure VLAN 4092 as the primary control VLAN of RRPP domain 1,
and configure the VLANs mapped to MSTI 1 as the protected VLANs of RRPP domain 1.
[RouterD] rrpp domain 1
[RouterD-rrpp-domain1] control-vlan 4092
[RouterD-rrpp-domain1] protected-vlan reference-instance 1
# Configure Router D as the transit node of primary ring 1, with GigabitEthernet 3/0/1 as the
primary port and GigabitEthernet 3/0/2 as the secondary port, and enable ring 1.
[RouterD-rrpp-domain1] ring 1 node-mode transit primary-port gigabitethernet 3/0/1
secondary-port gigabitethernet 3/0/2 level 0
[RouterD-rrpp-domain1] ring 1 enable
# Configure Router D as the edge node of subring 4, with GigabitEthernet 3/0/3 as the edge port,
and enable subring 4.
[RouterD-rrpp-domain1] ring 4 node-mode edge edge-port gigabitethernet 3/0/3
[RouterD-rrpp-domain1] ring 4 enable
# Configure Router D as the edge node of subring 5, with GigabitEthernet 3/0/4 as the edge port,
and enable subring 5.
[RouterD-rrpp-domain1] ring 5 node-mode edge edge-port gigabitethernet 3/0/4
[RouterD-rrpp-domain1] ring 5 enable
[RouterD-rrpp-domain1] quit
# Enable RRPP.
[RouterD] rrpp enable
5. Configure Router E:
# Create VLANs 1 through 30, map these VLANs to MSTI 1, and activate the MST region
configuration.
<RouterE> system-view
[RouterE] vlan 1 to 30
[RouterE] stp region-configuration
[RouterE-mst-region] instance 1 vlan 1 to 30
[RouterE-mst-region] active region-configuration
[RouterE-mst-region] quit
# Set the physical state change suppression interval to 0 seconds on GigabitEthernet 3/0/1 and
GigabitEthernet 3/0/2. Disable the spanning tree feature, configure the two ports as trunk ports,
and assign them to VLANs 1 through 30.
[RouterE] interface gigabitethernet 3/0/1
[RouterE-GigabitEthernet3/0/1] link-delay 0
[RouterE-GigabitEthernet3/0/1] undo stp enable