R3303-HP HSR6800 Routers High Availability Configuration Guide

106
[RouterA-mst-region] quit
# Set the physical state change suppression interval to 0 seconds on GigabitEthernet 3/0/1 and
GigabitEthernet 3/0/2, disable the spanning tree feature, and configure the two ports as trunk
ports. Remove the two ports from VLAN 1, assign them to VLANs 11 and 12, and configure VLAN
11 as their default VLAN.
[RouterA] interface gigabitethernet 3/0/1
[RouterA-GigabitEthernet3/0/1] link-delay 0
[RouterA-GigabitEthernet3/0/1] undo stp enable
[RouterA-GigabitEthernet3/0/1] port link-type trunk
[RouterA-GigabitEthernet3/0/1] undo port trunk permit vlan 1
[RouterA-GigabitEthernet3/0/1] port trunk permit vlan 11 12
[RouterA-GigabitEthernet3/0/1] port trunk pvid vlan 11
[RouterA-GigabitEthernet3/0/1] quit
[RouterA] interface gigabitethernet 3/0/2
[RouterA-GigabitEthernet3/0/2] link-delay 0
[RouterA-GigabitEthernet3/0/2] undo stp enable
[RouterA-GigabitEthernet3/0/2] port link-type trunk
[RouterA-GigabitEthernet3/0/2] undo port trunk permit vlan 1
[RouterA-GigabitEthernet3/0/2] port trunk permit vlan 11 12
[RouterA-GigabitEthernet3/0/2] port trunk pvid vlan 11
[RouterA-GigabitEthernet3/0/2] quit
# Create RRPP domain 1, configure VLAN 100 as the primary control VLAN of RRPP domain 1,
and configure the VLAN mapped to MSTI 1 as the protected VLAN of RRPP domain 1.
[RouterA] rrpp domain 1
[RouterA-rrpp-domain1] control-vlan 100
[RouterA-rrpp-domain1] protected-vlan reference-instance 1
# Configure Router A as the master node of primary ring 1, with GigabitEthernet 3/0/1 as the
primary port and GigabitEthernet 3/0/2 as the secondary port, and enable ring 1.
[RouterA-rrpp-domain1] ring 1 node-mode master primary-port gigabitethernet 3/0/1
secondary-port gigabitethernet 3/0/2 level 0
[RouterA-rrpp-domain1] ring 1 enable
[RouterA-rrpp-domain1] quit
# Create RRPP domain 2, configure VLAN 105 as the primary control VLAN of RRPP domain 2,
and configure the VLAN mapped to MSTI 2 as the protected VLAN of RRPP domain 2.
[RouterA] rrpp domain 2
[RouterA-rrpp-domain2] control-vlan 105
[RouterA-rrpp-domain2] protected-vlan reference-instance 2
# Configure Router A as the master node of primary ring 1, with GigabitEthernet 3/0/2 as the
master port and GigabitEthernet 3/0/1 as the secondary port, and enable ring 1.
[RouterA-rrpp-domain2] ring 1 node-mode master primary-port gigabitethernet 3/0/2
secondary-port gigabitethernet 3/0/1 level 0
[RouterA-rrpp-domain2] ring 1 enable
[RouterA-rrpp-domain2] quit
# Enable RRPP.
[RouterA] rrpp enable
2. Configure Router B: