HP Integrity cx2600 Operations and Maintenance Guide

Booting the Server
To boot the server, press the power switch located on the front panel.
If the autoboot function is enabled, the system will boot to the installed operating system. If
autoboot is not enabled, the system will enter the EFI boot manager. The EFI boot manager allows
you to control the server’s booting environment. For more information about the EFI boot
manager, review “Utilities” (page 73).
Fibre Channel (FC) Boot Configuration
The following procedure describes how to restore a Fibre Channel (FC) disk to the boot
environment.
NOTE: You must be able to navigate in the EFI Shell environment to perform the following
procedure.
The screen output shown in this procedure and the bold type that is selected in each of the steps
is from a hypothetical test setup; only your screen output shows the actual configuration of your
server.
1. Find the driver number for the FC disks. At the EFI Shell, enter the following command to
display all devices and their associated drivers:
Shell> drivers
T D
D Y C I
R P F A
V VERSION E G G #D #C DRIVER NAME IMAGE NAME
== ======== = = = == == =================================== ===================
12 00000010 B - - 6 20 PCI Bus Driver PciBus
1D 01020000 B X X 2 3 LSI Logic Ultra160 SCSI Driver PciRom Seg=00000000
1E 01020000 B X X 1 2 LSI Logic Ultra160 SCSI Driver PciRom Seg=00000000
23 00000109 D X X 1 - HP Tachyon XL2 Fibre Channel Mass S PciRom Seg=00000000
2A 00000110 D X X 1 - HP Tachyon XL2 Fibre Channel Mass S PciRom Seg=00000000
2E 00000029 D - - 2 - Usb Ohci Driver UsbOhci
2F 00000010 B - - 2 3 USB Bus Driver UsbBus
30 00001010 D X - 1 - Usb Keyboard Driver UsbKb
31 00000010 D - - 2 - Usb Mouse Driver UsbMouse
32 00000010 ? - - - - Usb Bot Mass Storage Driver UsbBot
33 00000010 ? - - - - Usb Cbi0 Mass Storage Driver UsbCbi0
34 00000010 ? - - - - <UNKNOWN> UsbCbi1
35 00000010 ? - - - - Generic USB Mass Storage Driver UsbMassStorage
36 00000010 ? - - - - UGA Console Driver GraphicsConsole
37 00000000 D - - 1 - PCI VGA Mini Port Driver PciVgaMiniPort
38 00000010 D - - 1 - VGA Class Driver VgaClassDriver
39 00000010 B - - 1 1 Serial 16550 UART Driver Serial16550
3A 00000010 B - - 1 1 Serial Terminal Driver Terminal
3B 00000010 D - - 2 - Platform Console Management Driver ConPlatform
3C 00000010 D - - 2 - Platform Console Management Driver ConPlatform
3D 00000010 B - - 2 2 Console Splitter Driver ConSplitter
3E 00000010 B - - 2 2 Console Splitter Driver ConSplitter
3F 00000010 B - - 2 2 Console Splitter Driver ConSplitter
40 00000010 B - - 2 2 Console Splitter Driver ConSplitter
49 00000010 D - - 14 - Generic Disk I/O Driver DiskIo
4A 00000010 B - - 3 10 Partition Driver(MBR/GPT/El Torito) Partition
4B 00000010 D - - 3 - FAT File System Driver Fat
4C 00000010 B X X 1 1 PCI IDE/ATAPI Bus Driver Ide
4D 00000010 ? - - - - Intel(R) PRO 100 UNDI Driver Undi
4E 00030007 B X X 3 3 Broadcom Gigabit Ethernet Driver b75Undi64
4F 00000010 D - - 3 - Simple Network Protocol Driver Snp3264
50 00000010 D - - 3 - PXE Base Code Driver PxeBc
51 00000010 D - - 3 - PXE DHCPv4 Driver PxeDhcp4
2. Determine the controller handle associated with each of the two listed drivers (23 and 2A).
Enter the following command:
Shell> drvcfg -c 23
108 Utilities