HP Integrity cx2620 Installation Guide HP Part Number: AB587-96010 Published: January 2007
© Copyright 2007 Hewlett-Packard Development Company, L.P Legal Notices The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
Table of Contents About This Document.......................................................................................................11 Intended Audience...................................................................................................................................11 New and Changed Information in This Edition..........................................................................................11 Publishing History................................................................
Installing a PCI-X Card..................................................................................................................31 Installing the PCI-X Card Cage Assembly.......................................................................................31 Installing Single-Core Processors.........................................................................................................32 Installing Dual-Core Processors.......................................................................
Troubleshooting Methodology.............................................................................................................71 Server Does Not Power On..................................................................................................................72 Troubleshooting Using the Front Panel Power Button............................................................................72 EFI Menu is Not Available..............................................................................
List of Figures 1-1 1-2 1-3 1-4 1-5 1-6 1-7 1-8 1-9 1-10 1-11 1-12 1-13 1-14 1-15 1-16 1-17 1-18 1-19 1-20 1-21 1-22 1-23 1-24 1-25 1-26 1-27 1-28 1-29 1-30 1-31 1-32 Server Top View.............................................................................................................................15 Server Front View..........................................................................................................................16 Server Rear View...........................................
List of Tables 1 Publishing History Details.................................................................................................................11 2 HP-UX 11i Releases............................................................................................................................12 1-1 Server Dimensions and Weights....................................................................................................17 1-2 Installation Sequence Checklist...................................
About This Document This document provides information and instructions on how to install the HP Integrity cx2620 server. The document printing date and part number indicate the document’s current edition. The printing date changes when a new edition is printed. Minor changes may be made at reprint without changing the printing date. The document part number changes when extensive changes are made. Document updates may be issued between editions to correct errors or document product changes.
Powering on the Server Booting the Operating System Troubleshooting Provides instructions on how to power on the server. Use this section to learn about booting the server to the operating system. Provides information that helps you diagnose common issues that can occur during server installation. Typographic Conventions This document uses the following conventions. WARNING! A warning lists requirements that you must meet to avoid personal injury.
Related Documents You can find other information on HP server hardware management and diagnostic support tools in the following publications. Web Site for HP Technical Documentation: Server Hardware Information: http://www.docs.hp.com http://www.docs.hp.com/hpux/hw/ Diagnostics and Event Monitoring: Hardware Support Tools Complete information about HP’s hardware support tools, including online and offline diagnostics and event monitoring tools, is at the http://docs.hp.com/hpux/diag/ Web site.
1 Installing the System Introduction The HP Integrity cx2620 server (Regulatory Model Number RSVLA-0303-DC) is a 64-bit, carrier grade server based on the Itanium® processor family architecture. This server is Network Equipment Building System (NEBS) level-3 compliant and is intended for telco users. The server accommodates one or two single-core or dual-core processors, from four to twelve DIMMs (providing 1 to 32 GB of memory), and internal peripherals including up to three disks and a CD/DVD.
Figure 1-2 Server Front View hp integrity cx2600 1 2 3 4 LAN System chasfront Figure 1-3 Server Rear View Fault DC Out Fault DC In DC Out DC In rearview Detailed Server Description The following sections provide information on the main subsystems within the HP Integrity cx2620 server. I/O Subsystem The I/O subsystem provides four hot-swappable 64-bit/133 MHz PCI-X slots. Processors The server accommodates one or two single-core or dual-core Itanium CPUs processors.
Front Display Panel, DVD, and Diagnostic Panel The LED status display is in the front of the unit directly above the DVD drive. The slimline DVD drive is also in the front of the unit. It is center-mounted in the unit and below the LED status display. Mass Storage The server has three hot-pluggable disk drives located in the front of the unit. Firmware Firmware consists of many individually linked binary images that are bound together by a single framework at run time.
Safety Information Use care to prevent injury and equipment damage when performing removal and replacement procedures. Voltages might be present within the server. Many assemblies are sensitive to damage by electrostatic discharge. Follow the safety conventions listed below to ensure safe handling of components, to prevent injury, and to prevent damage to the server: • • • • When removing or installing any server component, follow the instructions provided in this guide.
Table 1-2 Installation Sequence Checklist (continued) Step Description 8 Boot the operating system. 9 Verify the server configuration. Completed Unpacking and Inspecting the Server This section describes procedures you perform before installation. Ensure that you have adequately prepared your environment for the new server, received the components that you ordered, and verified that the server and its containers are in good condition after shipment.
IMPORTANT: Inspect each carton for shipping damage as you unpack the server. Checking the Inventory The sales order packing slip lists all of the equipment shipped from HP. Use this packing slip to verify that all of the equipment has arrived. NOTE: To identify each item by part number, see the sales order packing slip. Returning Damaged Equipment If the equipment is damaged, contact your HP customer service representative immediately.
Required Service Tools The HP Integrity cx2620 server may require one or more of the following tools for service: • • • • • Electrically Conductive Field Service Kit (P/N 9300-1609) 1/4 inch flat blade screwdriver ACX-15 Torx screwdriver ACX-10 Torx screwdriver IPF CPU install tool (P/N 5069-4551) Accessing a Rack-Mounted Server The HP Integrity cx2620 server is designed to be rack-mounted. The following procedure explains how to gain access to a server that is mounted in an approved rack.
1. 2. 3. 4. Turn off and disconnect system power. Disconnect power at the dc source end of the power cables, using the disconnect device that is part of the rack or facility power system. Label and disconnect all cables from the unit rear panel connectors. Remove or loosen (as appropriate) the screws that fasten the server to the rack. Label and disconnect the rack or facility ground cable from the chassis rear panel (Figure 1-4). Figure 1-4 Chassis Ground Lug Chassis Ground Lug chasgndlug 5. 6.
Hot-pluggable disk drives are located at the front of the server (Figure 1-5). The following sections describe how to install a hot-pluggable disk drive. Figure 1-5 Hot-pluggable Disk Drive Slots hp integrity cx2600 1 chasfront 2 3 4 LAN System Disk Slot 2 Disk Slot 1 Disk Slot 0 CAUTION: A hot-pluggable device can require interaction with the operating system before you can safely remove or install the device into the server.
NOTE: A hot-swappable device does not require interaction with the operating system before the device is removed from or installed into the server. If the second power supply is functioning correctly, you can power off and remove a power supply with no effect on server operations. Installing a Hot-Swappable Power Supply You can install a power supply while the server is installed in a rack. To install a hot-swappable power supply, follow these steps: 1. 2.
Figure 1-7 dc Power Supply Wire Connectors Fault DC Out Fault DC In DC Out DC In rearview dc Power Supply Wire 6. 7. 8. dc Power Supply Wire dc Power Supply Wire dc Power Supply Wire Install the terminal barrier strip cover. Hang the cover on the upper tabs and snap the cover into place. Route the power cable through the power supply cable clamp and tighten the two knurled knobs to secure the cable in place. Connect the power cable to the dc power source.
Figure 1-8 Installing the Front Grill chasfrntoff Captive Screws Removing the Front Grill NOTE: If you have an air filter assembly installed, remove the air filter assembly before removing the front grill. To remove the air filter assembly, see the HP Integrity cx2620 User Service Guide. To remove the front grill, follow these steps: 1. 2. Use the ACX-15 Torx screwdriver to loosen the five captive screws that secure the grill to the chassis. Pull the grill from the front of the server chassis.
WARNING! Voltages are present within the server when power is applied. Do not remove the server top cover without first turning off and disconnecting power. Always replace the top cover before turning the system on. 1. 2. 3. 4. 5. Power off and disconnect system power. Disconnect power at the dc source end of the power cables, using the disconnect device that is part of the rack or facility power system. Slide the server out from the rack until it stops.
3. 4. 5. Using the extractor handle, pull the fan from the server chassis. Orient the replacement fan so that the extractor handle is on the left. Insert the fan into the chassis opening and press it firmly into place. Tighten the two captive screws that secure the fan in place.
Figure 1-10 Removing a Rear Panel Hot-Swappable Fan Fan 5 Captive Screws chasfan5xtnd PCI-X Card Installation The server has four 64-bit, 133 MHz PCI-X accessory card sockets located in a removable card cage. You must remove the PCI-X card cage before you can remove or install PCI-X cards. The following sections describes how to remove and open the card cage, install PCI-X cards, and reinstall the PCI-X card cage.
3. If desired, remove the server from the rack and place it on an ESD protected work surface. See “Removing the Server from a Rack” (page 21). WARNING! Ensure that the system is powered off and all power sources are disconnected from the server prior to removing or installing server hardware unless you are removing or installing a hot-swappable or hot-pluggable component. Voltages are present at various locations within the server whenever a dc power source is connected.
NOTE: The four connectors within the card cage are identical and have the same capabilities. You can install a compatible PCI-X card in any slot. Installing a PCI-X Card NOTE: You must remove the PCI-X card cage from the server chassis to enable installation of PCI-X cards. The four connectors in the PCI-X card cage are identical and have the same capabilities. You can install a compatible PCI-X card in any slot. You can remove cards by lifting them from the sockets.
Figure 1-12 Installing the PCI-X Card Cage PCI Card Cage Release Lever chaspciccup 3. 4. 5. 6. Press the release lever down to lock the card cage into place in the chassis. Install the chassis top cover. See “Installing the Top Cover” (page 26). Reconnect rear panel cables, and turn on the system. Run the info io command at the EFI Shell to verify that you have correctly installed the PCI-X card.
Figure 1-13 Processors in Server Chassis (Top Cover Removed) CPU 0 CPU 1 F R O N T B A C K chastop2cpus The following procedure is applicable to installation of processor 0 or processor 1. You must install processor 0 before installing processor 1. NOTE: Installation instructions are provided with replacement processors. Read those instructions carefully. Changes in processor design and installation may have occurred since this procedure was written.
5. Remove the chassis top cover. See “Removing the Top Cover” (page 26). CAUTION: Observe all ESD safety precautions while performing processor installation. Failure to follow ESD safety precautions can result in damage to the server. 6. 7. Remove the processor airflow guide by lifting it up and out of the server. Ensure that the processor locking mechanism is rotated to the unlocked position (Figure 1-14). Figure 1-14 Processor Locking Mechanism Unlocked Locked Front of Chassis 8. 9.
CAUTION: Do not press the processor module into the socket. When properly aligned, the processor pins seat into the socket by themselves. No additional pressure is required. You can damage the pins if you apply pressure. Figure 1-15 Aligning the Processor Power Module When properly aligned, the connector of the processor and heatsink assembly face the rear of the chassis 11. Use the Allen side of the IPF-CPU tool to lock the processor in place on the system board.
Figure 1-16 Securing Heatsink Captive Screws Screw 1 (not shown) (Tighten first) Insert IPF-CPU Tool Here Screw 3 (Tighten third) Screw 4 (Tighten last) Screw 2 (Tighten second Locator Post Locator Post Locator Hole Locator Hole cpu1noppm3 14. Connect the power cable for the processor turbo fan to its connector on the system board. 15. Slide the CPU power module on the system board metal mounting bracket so that the power module connector aligns with the connector on the processor.
Figure 1-17 Sliding the Processor Power Module Front of Chassis 16. Align the two mounting screw holes on the power module with their screw holes on the system board’s metal mounting bracket. Screw in the power module mounting screws (M3 x 23mm long pan T15 crest cup stainless steel, two per CPU). Figure 1-18 Installing the Power Module Mounting Screws Front of Chassis 17. Connect the processor module turbo fan power cable to the connector on the system board.
Figure 1-19 Connect the Turbo Fan Cable Front of Chassis 18. Connect the CPU power module power cable to the connector on the system board. Figure 1-20 Connect the Power Module Cable Front of Chassis 19. 20. 21. 22. 23. 24. Place the processor airflow guide in position. Install the chassis top cover. See “Installing the Top Cover” (page 26). If necessary, reinstall the chassis in the rack. See “Install the Server into a Rack” (page 22). Reconnect power and system cables to rear panel connectors.
The server may be delivered with one or two dual-core processors installed. You can install the second processor, or replace the processors with newer, compatible processors. The following sections provide detailed procedures for processor installation. A tool kit is provided with replacement processors. An IPF-CPU tool kit is required for successful completion of these procedures.
4. 5. 6. 7. 8. 9. Remove the chassis top cover. See “Removing the Top Cover” (page 26). Remove the processor airflow guide by lifting it up and out of the server. Ensure that the processor locking mechanism is rotated to the unlocked position. Inspect the pins of the processor you are installing. Verify that processor pins are not bent.
Figure 1-23 Connecting the Power Cable and Turbo Fan Cable 16. 17. 18. 19. 20. 21. Place the processor airflow guide in position. Install the chassis top cover. If necessary, reinstall the chassis in the rack. Reconnect power and system cables to rear panel connectors. Power on the server. Run the info cpu command at the EFI Shell prompt to verify that the processor has been installed correctly. Installing Memory The server comes with four, eight, or twelve DIMMs installed.
DIMMs in the first quad. If you install DIMMs in the third quad, they must be equal to or smaller than the DIMMs in the second quad. WARNING! Ensure that the system is powered off and all power sources are disconnected from the server prior to removing or installing server hardware unless you are removing or installing a hot-swappable or hot-pluggable component. Voltages are present at various locations within the server whenever a dc power source is connected.
NOTE: 9. DIMM connectors are keyed so they can only be installed in the correct orientation. Firmly and evenly push on each side of the DIMM until it seats in the socket. The socket retainer clips return to the upright position when the DIMM is fully inserted. Figure 1-25 Inserting a DIMM into a DIMM Socket dimm_sokt 10. Snap the socket retainer clips into place, ensuring that the DIMM is locked into the socket. 11. Repeat steps 7 through 10 for each DIMM to be installed. 12.
The guide is located on the Web at: http://www.hp.com/racksolutions Select mounting information from the menu, then select the guide titled Mounting in non-HP racks. Connecting Cables This section provides information on cables and cable connections. This section addresses the following topics: • • “DC Input Power” (page 44) “Core I/O Connections” (page 48) DC Input Power The server comes with two power supplies installed each powered from its own power cable.
Figure 1-26 Power Supply Rear View Negative Positive + + – – Fault DC Out DC In psrearpnl2 WARNING! Ensure that the system is powered off and all power sources are disconnected from the server prior to removing or installing server hardware unless you are removing or installing a hot-swappable or hot-pluggable component. Voltages are present at various locations within the server whenever a dc power source is connected. This voltage is present even when the main power switch is turned off.
• • • Standby power Full power Off Plug the power cord into the appropriate receptacle on the rear of the chassis to achieve the standby power state; the front panel Power button is not turned on. Full power occurs when the power cord is plugged into the appropriate receptacle, and the Power button is activated. In the off state, the power cords are not plugged in. Table 1-3 lists the server power states.
Figure 1-27 dc Power Supply Wire Connectors Fault DC Out Fault DC In DC Out DC In rearview dc Power Supply Wire 2. dc Power Supply Wire dc Power Supply Wire dc Power Supply Wire Connect the dc power plugs into the outlet. The server goes into standby power mode as soon as the power cable is connected to the power inlet. NOTE: If the fans turn on, the system may be in full power-on mode.
Interval Two Approximately 30 seconds later, the bulk power supplies flash green and the amber light is still present on the hard disk drives. Standby power is now on. Core I/O Connections The server has one core I/O card installed. Each core I/O card has an ilO MP. Each core I/O card is oriented vertically and accessed from the back of the server.
• • • • One 1 Gb LAN-RJ45 SCSI LVD/SE connector Four PCI-X connections (0 to 4 PCI-X cards can be used) Two console serial ports (A and B) Console Setup Setting up the console involves the following: • Determining the physical access method to connect cables. There are two physical connections to the Integrity iLO MP: RS-232 and LAN. • Configuring the Integrity iLO MP and assigning an IP address if necessary. Though there are several methods to configuring the LAN, DHCP with DNS is the preferred one.
Table 1-4 Setup Checklist (continued) Step Action Advanced 1 Activate Advanced Pack Activate advanced features by entering a license key. Features Setup Flowchart Use this flowchart as a guide to assist in the setup process.
Figure 1-29 Setup Flowchart Preparation There are several tasks to perform before you can configure the iLO MP LAN.
• • Determine the physical access method to select and connect cables. Determine the iLO MP LAN configuration method and assign an IP address if necessary. Determining the Physical iLO MP Access Method Before you can access the iLO MP, you must first determine the correct physical connection method. The iLO MP has a separate LAN port from the system LAN port. It requires a separate LAN drop, IP address, and networking information from that of the port used by the operating system.
Table 1-5 Console Connection Matrix (continued) Operating System Console Connection Method Required Connection Components Linux Local RS-232 serial console port remote/modem port 1. M-cable: DB25 connector on one end, and three DB-9F connectors on the other end: • Console (ilO MP) • Remote • UPS 2. RS-232 DB-9F to DB-9F cable (modem eliminator cable) 3.
HP recommends using the DHCP and DNS method to simplify access to the iLO MP. When you use DHCP and DNS, you can connect to the iLO MP by typing the default host name in your browser rather than an IP address only if the following applies: • • • • DHCP must be enabled (DHCP is enabled by default). You are using a DHCP server that provides the domain name and the primary DNS server IP address. The primary DNS server accepts dynamic DNS (DDNS) updates.
1. 2. Connect a PC to the network that is on the same physical subnet as the server and run the ARP Ping commands from the PC. Locate an existing server on the network, log into it, and run the ARP Ping commands from the server. Table 1-7 lists the ARP Ping commands. Table 1-7 ARP Ping Commands ARP Command Description arp -s This command assign the IP address to the iLO MP MAC address.
IMPORTANT: Ensure you have a console connection through the RS-232 serial console port or a network connection through the LAN to access the iLO MP and use the LC command. To assign a static IP address using the LC command, follow these steps: 1. Ensure the emulation software device is properly configured. The terminal emulation device runs software that interfaces with the server.
Logging In to the iLO MP To log in to the iLO MP, follow these steps: 1. 2. Access the iLO MP using the LAN, RS-232 serial console port, telnet, SSH, or Web method. The iLO MP login prompt displays. Log in using the default the iLO MP user name and password (Admin/Admin). The MP Main Menu screen displays. TIP: For security reasons, HP strongly recommends you modify the default settings during the initial login session. See “Modifying User Accounts and Default Password” (page 57).
a. b. c. 3. Access the MP Main Menu. Enter CM at the MP> prompt. Enter UC at the MP:CM> prompt and follow the prompts to modify default passwords. To setup user accounts: a. Access the MP Main Menu. b. Enter CM at the MP> prompt. c. Enter UC at the MP:CM> prompt and follow the prompts to modify user accounts.
Interacting With the iLO MP Using the Web GUI Web browser access is an embedded feature of the iLO MP. The iLO MP has a separate LAN port from the system LAN port. It requires a separate LAN drop, IP address, and networking information from that of the port used by the operating system. IMPORTANT: Make sure you use the MAC address to the iLO MP LAN and not the MAC address to the server core LAN.
Figure 1-32 Status Summary Page Function Tabs Navigation Bar Display Screen 1. 2. 3. Select the Web interface functions by clicking the Function tabs at the top of the page. Each function lists options in the Navigation Bar on the left side of the page. Click an option link to display data in the Display screen; and click Refresh to update the display. Click the Remote Console tab. The remote console provides a serial console that behaves similarly to the TUI.
1. 2. Perform preparation tasks. Connect the cables. a. Connect the monitor VGA cable to the appropriate VGA port on your server. b. Connect the keyboard USB cable to the appropriate USB port on your server. c. Connect the mouse USB cable to the appropriate USB port on your server. 3. Power on the server. The EFI Shell prompt displays. Powering OFF and Powering On the Server This section provides information and procedures for powering off and powering on the server.
1. 2. 3. 4. 5. Gracefully shut down the operating system. See operating system documentation for more information. Start a console session, and access the iLO MP Main Menu. Enter CM to enable command mode. Enter PC to use the remote power control command. Enter OFF to power off the server, and enter YES when prompted to confirm the action. IMPORTANT: All the dc voltage except for the standby power is now turned off from the server. Therefore, dc voltage for standby power is still present in the server. 6.
Configuring System Boot Options You can configure system boot options on the server, including the boot options list and the autoboot setting for the server. • Boot Options List The boot options list is a list of loadable items you can select from the EFI Boot Manager menu. Ordinarily the boot options list includes the EFI Shell and one or more operating system loaders. To manage the boot options list for each system, use the EFI Shell, the EFI Boot Configuration Menu, or the operating system utilities.
Adding HP-UX to the Boot Options List This section describes how to add an HP-UX entry to the system boot options list. You can add the \EFI\HPUX\HPUX.EFI loader to the boot options list from the EFI Shell or the EFI Boot Configuration Menu, (or in some versions of EFI, the Boot Options Maintenance Menu). The operating system installer automatically adds an entry to the boot options list. To add an HP-UX boot option when logged in to HP-UX, use the setboot command.
1. 2. 3. Access the EFI Boot Manager menu for the system on which you want to boot HP-UX. Log in to the iLO MP and enter CO to select the system console. When accessing the console, confirm that you are at the EFI Boot Manager menu. If you are at another EFI menu, select Exit from the sub menus until you return to the screen with the EFI Boot Manager titles. At the EFI Boot Manager menu, select an item from the boot options list.
blk4 : Acpi(000222F0,2A8)/Pci(0|1)/Scsi(Pun2,Lun0) Shell> fs0: fs0:\> hpux (c) Copyright 2002-2007, Hewlett Packard Company. All rights reserved HP-UX Boot Loader for IA64 Revision 1.723 Press Any Key to interrupt Autoboot \efi\hpux\AUTO ==> boot vmunix Seconds left till autoboot 9 7. Exit the console and iLO MP interfaces. Press Control-B to exit the system console and return to the iLO MP Main Menu. To exit the iLO MP, type X at the main menu.
HPUX> boot -is vmunix > System Memory = 4063 MB loading section 0 ................................................... (complete) loading section 1 ........ (complete) loading symbol table loading System Directory(boot.sys) to MFS .... loading MFSFILES Directory(bootfs) to MFS ...... Launching /stand/vmunix SIZE: Text:25953K + Data:3715K + BSS:3637K = Total:33306K Console is on a Serial Device Booting kernel... 8. Exit the console and iLO MP interfaces.
1. Log in to HP-UX running on the system that you want to shut down. Log in to iLO MP for the server and use the Console menu to access the system console. Accessing the console through the iLO MP enables you to maintain console access to the system after HP-UX has shut down. 2. Issue the shutdown command with the appropriate command-line options. The command-line options you specify dictate the way in which HP-UX shuts down, and whether the system is rebooted.
• • bcfg boot mv #a #b — Moves the item number specified by #a to the position specified by #b in the boot options list. bcfg boot add # file.efi "Description" — Adds a new boot option to the position in the boot options list specified by #. The new boot option references file.efi and is listed with the title specified by Description. For example, bcfg boot add 1 \EFI\redhat\elilo.efi "Red Hat Enterprise Linux"adds a Red Hat Enterprise Linux item as the first entry in the boot options list.
To interact with the ELILO.EFI loader, interrupt the boot process (for example, type a space) at the ELILO boot prompt. To exit the loader, issue the exit command. Shutting Down Linux Use the shutdown command to shut down Linux. The Linux shutdown command has the following options: Halts (powers off) after operating system shutdown. -h Use the PC command at the iLO MP Command menu to manually power on or power off server hardware as needed. Reboots the server after shutdown. Cancels a running shutdown.
• • “Console Problems” (page 73) “Downloading and Installing the Latest Version of the Firmware” (page 73) Troubleshooting Methodology WARNING! Always disconnect the power cords and unplug telephone cables before removing the server cover. Disconnect telephone cables to avoid exposure to shock hazard from telephone ringing voltages. Disconnect the power cords to avoid exposure to high energy levels that can cause burns when parts are short-circuited by metal objects such as tools or jewelry.
Server Does Not Power On Power problems during installation are usually related to the installation process. If the server does not power on, check the LED indicators on the power supply rear panels and perform the following actions: • • • If the dc In indicators are lit, it is assumed that power is available to the server. If a fault indicator is lit, reseat the power supply. If the problem persists, remove and reseat boards within the server.
Operating System Boots with Problems If the operating system is running, you are experiencing problems, use the following tools to help solve the problem: • • LEDs Error Messages and event logs Intermittent Server Problems You can usually trace intermittent problems that occur during installation to power source problems, a loose connector, or some other hardware problem. If you are experiencing intermittent problems, follow these steps: 1. 2. 3. 4. 5. 6. Check iLO MP logs and analyze the problem.
To ensure you have the latest version of the firmware running on the server, download the latest version of the firmware from the Web, and create a CD to install the firmware on the server. You can update firmware by using the HP Firmware Manager (HP FM). HP FM is a set of tools for updating firmware on an HP Integrity system. HP FM is packaged with the firmware and distributed through the web. HP FM provides two methods of updating firmware.
Index A accessing a rack-mounted server, 21 aluminum conductors, dc power, 45 antistatic wrist strap, 18 C configure iLO MP LAN using ARP Ping, 54 using DHCP and DNS, 53 using RS-232 serial console port, 55 console problems, 73 console session, determining connection method, 52 console setup checklist, 49 configuration, 53 connection matrix, 52 flowchart, 50 iLO MP LAN configuration, 53 physical access, 52 preparation, 51 using ARP ping, 54 using DHCP and DNS, 53 using the RS-232 serial console port, 55 co
assigning with LC command, 55 O operating system booting and shutting down HP-UX, 63 booting and shutting down Linux, 68 boots with problems, 73 configuring system boot options, 63 does not boot, 72 supported, 62 verifying server configuration, 70 P passwords, default, 57 PCI-X card installing, 29 removing fan, 29 PCI-X card cage installing, 29 removing fan, 29 power button, 72 off manually, 62 off using the iLO MP, 61 on manually, 61 on using the iLO MP, 61 problems, 72 standby, 47 supplies, rear view, 2
