Native Inspect Manual (H06.13+, J06.03+)

Examples
• To display memory at address 0x70000fc0 and then display three machine instructions
starting at that address:
(eInspect 7,464): x 0x70000fc0
0x70000fc0:0 <func_1+416>: 0x0900cc68
(eInspect 7,464): x /3i 0x70000fc0
0x70000fc0:0 <func_1+416>: [MMI] st4 [r52]=r51
0x70000fc0:1 <func_1+422>: addl r53=192,r1
0x70000fc0:2 <func_1+428>: nop.i 0x0;;
• To display memory at an address:
(eInspect 0,794): x /20c 0x70000ca8
0x70000ca8 <__STRING$4>: 109 'm' 111 'o' 110 'n' 105
'i' 116 't' 111 'o' 114 'r' 0 '\000'
0x70000cb0 <__STRING$6>: 102 'f' 114 'r' 101 'e' 100
'd' 0 '\000' 0 '\000' 0 '\000' 0 '\000'
0x70000cb8 <__STRING$5>: 100 'd' 112 'p' 50 '2' 0 '\
000'
• To display memory referenced by a pointer:
(eInspect 0,794): x /5xw pcbAttribute
0x8004ee0: 0x00030000 0x00000005 0x00000000 0x00000000
0x8004ef0: 0x00000000
(eInspect 0,794): x /5b pcbAttribute
0x8004ee0: 0x00 0x03 0x00 0x00 0x00
• To display instructions relative to the current location:
(eInspect 3,663): x /5i $ip
0x70002bf0:0 <pcbDataStructs_initialize+2256>: [MMI] break.m 0x2a;;
0x70002bf0:1 <pcbDataStructs_initialize+2262>: ld8 r35=[r34]
0x70002bf0:2 <pcbDataStructs_initialize+2268>: nop.i 0x0;;
0x70002c00:0 <pcbDataStructs_initialize+2272>: [MMI] adds r36=4,r35;;
0x70002c00:1 <pcbDataStructs_initialize+2278>: adds r37=44,r36
• Use the following commands to display data in t (binary), o (octal), d (signed decimal), u
(unsigned decimal), and x (hexadecimal) format:
(eInspect 7,498): x 0x6ffffee0
0x6ffffee0: 0x00250000
(eInspect 7,498): x /t 0x6ffffee0
0x6ffffee0: 00000000001001010000000000000000
(eInspect 7,498): x /o 0x6ffffee0
0x6ffffee0: 011200000
(eInspect 7,498): x /d 0x6ffffee0
0x6ffffee0: 2424832
(eInspect 7,498): x /u 0x6ffffee0
0x6ffffee0: 2424832
(eInspect 7,498): x /x 0x6ffffee0
0x6ffffee0: 0x00250000
• Use the following command to specify the current default to continue displaying memory.
When you enter a format specification and an address, the x command uses those values as
the defaults until you change the specification:
(eInspect 6,1103): x /3i 0x70000ca8
0x70000ca8 <__STRING$2+24>: data8 0x14c84a407a
0x70000cb2 <__STRING$2+34>: [MII] break.m 0x0
0x70000cb8 <__STRING$2+40>: break.i 0x0
(eInspect 6,1103): x/2
0x70000cbe <__STRING$2+46>: break.i 0x0
0x70000cc2 <__STRING$3+2>: [MII] data8 0x103932ba333
(eInspect 6,1103): x /7
0x70000cc8 <__STRING$3+8>: (p16) cmp4.eq p7,p16=45,r25
0x70000cce <__STRING$3+14>: data8 0xc8dcdec6ca
0x70000cd2 <__STRING$3+18>: [MII] data8 0x15b1b7b6311
x Command 127