NonStop NS16000 Series Planning Guide (H06.11+)

• Changed “QMS Tech Doc” to “Technical Document shipped with the system in “CLIM Cable
Management Ethernet Patch Panel” (page 122).
• Restricted coexistence of DL385 G5 Storage CLIMs and DL380 G6 Storage CLIMs in “Storage
CLuster I/O Module (CLIM)” (page 123).
• Changed RVU requirement to H06.24 or later to support SSDs in D2700 disk enclosures in
“Serially Attached SCSI (SAS) Disk Enclosure” (page 124).
New and Changed Information for 529567–022
With H06.23 and later RVUs, NonStop NS16000 series systems support IB CLIMs. Networking
CLIMs include IP, Telco, and IB CLIMs.
With H06.23 and later RVUs, NonStop NS16000 series systems support Solid State Drives (SSDs)
contained in D2700 disk enclosures connected to DL380 G6 Storage CLIMs.
These changes have been made. All changes are marked with change bars.
• Changed category 5 cable (CAT 5) to Category 6 cable (CAT 6) throughout the document
and indicated that Category 5e cable (CAT 5e) is also acceptable.
• Changed Table 1 (page 19) in “NonStop NS16000 Series System Overview” (page 19).
• Changed “HP StorageWorks” to “HP Storage” and added IB CLIM and SSD to “NonStop
NS16000 Series Hardware ” (page 20).
• Added IB CLIM as type of networking CLIM in “Processor Switch Group-Module-Slot
Numbering” (page 26) and “CLIM Connection Group-Module-Slot-Port Numbering” (page 27).
• Changed location of extension bars connected to modular UPS or R5500 XR UPS to rear left
side of cabinet in “Modular Cabinet Power and I/O Cable Entry” (page 32). Also changed
remaining PDU location to rear right side.
• Added cross-references and changed location of extension bars connected to modular UPS
or R5500 XR UPS to rear left side of cabinet in “Uninterruptible Power Supply (UPS)” (page 33).
• Changed location of extension bars connected to modular UPS or R5500 XR UPS to rear left
side of cabinet and changed remaining PDU location to rear right side in “Modular Cabinets”
(page 37), “Top AC Power Feed When Optional UPS and ERM are Installed” (page 39),
Figure 4 (page 40), “Bottom AC Power Feed When Optional UPS and ERM are Installed”
(page 40), Figure 5 (page 41), “Branch Circuits and Circuit Breakers, Monitored Single-Phase
PDUs” (page 42), “Top AC Power Feed When Optional UPS and ERM are Installed” (page 44),
Figure 8 (page 45), “Top AC Power Feed When Optional UPS and ERM are Installed”
(page 50), and Figure 9 (page 46).
• Removed R5500 XR UPS designation from “Branch Circuits and Circuit Breakers, Monitored
Three-Phase PDUs” (page 47).
• Added IB CLIM and SSD to “Enclosure Power Loads” (page 55).
• Changed DL385 G2 or G5 CLIM height to 3.4 inches (8.6 cm) in “Enclosure Dimensions”
(page 58).
• Added SSD to “Modular Cabinet and Enclosure Weights With Worksheet” (page 59).
• Added IB CLIM (as networking CLIM) and SSD to “Heat Dissipation Specifications and
Worksheet” (page 60).
• In “System Configuration Guidelines” (page 66) changed second paragraph, removed example
configuration, and moved section “Enclosure Locations in Cabinets” to “Hardware
Configurations” (page 135).
• Changed “IP or Telco CLIM” to “networking CLIM” to add IB CLIM in “Cable Length Restrictions”
(page 69) and “Processor Switch ServerNet Connections” (page 75).
8