RDF System Management Manual for J-series and H-series RVUs (RDF Update 13)

command. This can also be obtained if you are using ASAP ( see Appendix E (page 492)). The
display returned by the RDFCOM STATUS RDF command is as follows:
]STATUS RDF
In response, RDF displays:
RDFCOM - T0346H09 – 11AUG08
(C)2008 Hewlett-Packard Development Company, L.P.
Status of \RDF04 -> \RDF05 RDF 2008/08/11 05:26:49.082
Control Subvol: $SYSTEM.RDF04
Current State : Normal
RDF Process Name RTD Time Pri Volume Seqnce Rel Byte Addr Cpus Err
------------------ ------ --------- --- -------- ------ ------------- ----- ----
Monitor $RMON 185 $AUDIT 56 1: 2
Extractor (0) $REXT0 0:00 185 $AUDIT 56 928000 1: 2
Extractor (1) $REXT1 0:00 185 $DATA17 4 10435580 1: 2
Receiver (0) $RRCV0 0:00 185 $MIT 44 1: 2
Receiver (1) $RRCV1 0:00 185 1: 2
Imagetrail (0) $IMAGE0 22
Imagetrail (1) $IMAGEA 3
Purger $RPRG 185 1: 2
$DATA06 -> $DATA06 $RUPD1 0:06 185 $IMAGE0 22 9568 1: 2
$DATA07 -> $DATA07 $RUPD2 0:00 185 $IMAGEA 3 811008 2: 3
$DATA08 -> $DATA08 $RUPD3 0:06 185 $IMAGEA 3 811568 3: 0
In the STATUS RDF display, the first line gives the name of the primary system (\RDF04 in this
example), the name of the backup system (\RDF05 in this example), and the timestamp that shows
when the STATUS RDF command was issued. The second line specifies the fully-qualified name of
the control subvolume.
RDF States
The third line specifies the current state of the subsystem; any of the following entries are possible:
Table 9 RDF States
DescriptionStatus
RDF running with Update OnNormal
RDF running with Update OffNormal - Update Stopped
RDF was running with Update Off, Update was just turned On, but one
or more updaters have not yet started.
Start Update Pending
RDF was running with Update On, Update was just turned Off, but one
or more updaters have not yet stopped.
Stop Update Pending
RDF was running with Update On, you issued a STOP UPDATE
command with the timestamp option, but one or more updaters have
not reached the end of Redo and/or Undo operations.
Stop Update, Timestamp Pending
RDF was running with Update On, you have issued a STOP RDF
command, but one or more RDF processes have not yet stopped.
* STOP RDF In Progress *
RDF was running with either Update On or Off, you have issued a
TMFCOM STOP TMF command on the primary system, the master
* TMF STOP In Progress *
extractor has detected the STOP TMF audit record, but one or more
RDF processes have not yet stopped in response.
You have tried to START RDF, but the RDF software on the backup
system is not compatible with the RDF software on the primary system.
WRONG PROGRAM VERSION
RDF was running with Update On, a Shared Access NonStop SQL/MP
or SQL/MX operation was detected, but some updaters have not yet
shutdown.
NSA Stop Update Pending
RDF had been running with Update On, a Shared Access NonStop
SQL/MP or SQL/MX operation was detected, and all updaters have
Update NSA Stopped
completed the shutdown or have suspended (based on the value of the
102 Operating and Monitoring RDF