TMF Management Programming Manual (H06.06+, J06.03+)
Table Of Contents
- HP NonStop TMF Management Programming Manual
- Legal Notices
- Contents
- What’s New in This Manual
- About This Manual
- 1 Introduction to TMF
- 2 Communicating With the TMFSERVE Process
- 3 SPI Programming Considerations for TMF
- 4 Common Definitions
- 5 Commands and Responses
- Command Summary
- Command Descriptions
- ABORT TRANSACTION
- ADD AUDITTRAIL
- ADD DATAVOLS
- ADD DUMPS
- ADD MEDIA
- ADD RESOURCEMANAGER
- ALTER AUDITDUMP
- ALTER AUDITTRAIL
- ALTER BEGINTRANS
- ALTER CATALOG
- ALTER DATAVOLS
- ALTER DUMPS
- ALTER MEDIA
- ALTER PROCESS
- ALTER TMF
- CANCEL OPERATION
- CLOSE RESOURCEMANAGER
- DELETE CATALOG
- DELETE DATAVOLS
- DELETE DUMPS
- DELETE MEDIA
- DELETE RESOURCEMANAGER
- DELETE TMF
- DELETE TRANSACTION
- DISABLE AUDITDUMP
- DISABLE BEGINTRANS
- DISABLE DATAVOLS
- DUMP FILES
- ENABLE AUDITDUMP
- ENABLE BEGINTRANS
- ENABLE DATAVOLS
- INFO ATDUMPDM
- INFO ATVOLUME
- INFO AUDITDUMP
- INFO AUDITTRAIL
- INFO BEGINTRANS
- INFO CATALOG
- INFO DATAVOLS
- INFO DUMPS
- INFO MEDIA
- INFO PROCESS
- INFO RESOURCEMANAGER
- INFO TMF
- LIST AUDITTRAIL
- NEXT AUDITTRAIL
- RECOVER FILES
- RELOCATE DISKDUMPS
- RESOLVE TRANSACTION
- START TMF
- STATUS ATFILE
- STATUS AUDITDUMP
- STATUS AUDITTRAIL
- STATUS BEGINTRANS
- STATUS CATALOG
- STATUS DATAVOLS
- STATUS OPERATION
- STATUS RESOURCEMANAGER
- STATUS RMTRANSBRANCHES
- STATUS TMF
- STATUS TMFSERVER
- STATUS TRANSACTION
- STATUS TRANSACTIONCHILDREN
- STOP TMF
- 6 Event Messages
- 7 Error and Warning Messages
- A TMF Configuration Limits and Defaults
- Index
Commands and Responses
HP NonStop TMF Management Programming Manual—540140-010
5-132
INFO TMF
Tokens in Response Buffer
ZTMF-TKN-VolumeName
specifies the current TMF configuration volume.
ZTMF-TKN-ATFileFormat
specifies the current audit-trail file format. A value of 1 indicates format 1. A value
of 2 indicates format 2.
ZTMF-MAP-Info-Tmf
is an extensible structured token containing INFO TMF command token values.
This token contains the following fields:
ZGoRemote
specifies the method currently being used to send GoRemote requests to the
TMP to establish distributed transactions. The following values are valid:
ZPioBuffer
specifies the current PIO buffer settings (which establish the transport buffer
configuration). See the struct ZTMF-DDL-PioBuffer under Private Token and
Field Types on page 4-6.
ZTmpWaitTimer
specifies the current TMP wait timer setting (which determines how often the
TMP wakes to check for pending transaction completions). See the struct
ZTMF-DDL-TmpWaitTimer under Private Token and Field Types on page 4-6.
ZTransProtocol
specifies the current transaction flush protocol used to flush transactions upon
their completion. The following values are valid:
ZDisasterRecovery
Specifies Disaster Recovery setting. The TMF Disaster Recovery Mode is used
to control TMF operations in special Disaster Recovery situations. See
ZTMF-VAL-GoRemote-Pio PIOs are being used.
ZTMF-VAL-GoRemote-PioPri PIOs are being used and they are
being put ahead of transaction
completions in the TMP queue.
ZTMF-VAL-GoRemote-Msg The Message System is being used.
ZTMF-VAL-TransProto-MMI MMI protocol.
ZTMF-VAL-TransProto-Standard Standard protocol.