TMF Management Programming Manual (H06.06+, J06.03+)
Table Of Contents
- HP NonStop TMF Management Programming Manual
- Legal Notices
- Contents
- What’s New in This Manual
- About This Manual
- 1 Introduction to TMF
- 2 Communicating With the TMFSERVE Process
- 3 SPI Programming Considerations for TMF
- 4 Common Definitions
- 5 Commands and Responses
- Command Summary
- Command Descriptions
- ABORT TRANSACTION
- ADD AUDITTRAIL
- ADD DATAVOLS
- ADD DUMPS
- ADD MEDIA
- ADD RESOURCEMANAGER
- ALTER AUDITDUMP
- ALTER AUDITTRAIL
- ALTER BEGINTRANS
- ALTER CATALOG
- ALTER DATAVOLS
- ALTER DUMPS
- ALTER MEDIA
- ALTER PROCESS
- ALTER TMF
- CANCEL OPERATION
- CLOSE RESOURCEMANAGER
- DELETE CATALOG
- DELETE DATAVOLS
- DELETE DUMPS
- DELETE MEDIA
- DELETE RESOURCEMANAGER
- DELETE TMF
- DELETE TRANSACTION
- DISABLE AUDITDUMP
- DISABLE BEGINTRANS
- DISABLE DATAVOLS
- DUMP FILES
- ENABLE AUDITDUMP
- ENABLE BEGINTRANS
- ENABLE DATAVOLS
- INFO ATDUMPDM
- INFO ATVOLUME
- INFO AUDITDUMP
- INFO AUDITTRAIL
- INFO BEGINTRANS
- INFO CATALOG
- INFO DATAVOLS
- INFO DUMPS
- INFO MEDIA
- INFO PROCESS
- INFO RESOURCEMANAGER
- INFO TMF
- LIST AUDITTRAIL
- NEXT AUDITTRAIL
- RECOVER FILES
- RELOCATE DISKDUMPS
- RESOLVE TRANSACTION
- START TMF
- STATUS ATFILE
- STATUS AUDITDUMP
- STATUS AUDITTRAIL
- STATUS BEGINTRANS
- STATUS CATALOG
- STATUS DATAVOLS
- STATUS OPERATION
- STATUS RESOURCEMANAGER
- STATUS RMTRANSBRANCHES
- STATUS TMF
- STATUS TMFSERVER
- STATUS TRANSACTION
- STATUS TRANSACTIONCHILDREN
- STOP TMF
- 6 Event Messages
- 7 Error and Warning Messages
- A TMF Configuration Limits and Defaults
- Index
Commands and Responses
HP NonStop TMF Management Programming Manual—540140-010
5-145
RELOCATE DISKDUMPS
RELOCATE DISKDUMPS
The RELOCATE DISKDUMPS command changes the disk media locations for TMF
catalog entries.
Command Syntax
For information on the tokens present in the command and response buffers, see the
SPI Programming Manual.
Tokens in Command Buffer
ZTMF-TKN-DumpSerial
specifies the serial number of a dump. This token is required; multiple occurrences
are allowed. The special value ZTMF-VAL-WildDumpSerial specifies all dumps
that reside on a specified node. This token is used in place of a valid volume
name; it can not be used with a valid volume name.
ZTMF-TKN-OldDmLoc
specifies the current system and volume name of the catalog entries that are being
altered. The system name is optional; if it is not included, the local system name is
used. This token is required; only one occurrence is allowed; a wild card value is
allowed.
Command
ZTMF-CMD-Relocate
Object Type
ZTMF-OBJ-DiskDumps
Tokens in Command Buffer
ZTMF-TKN-DumpSerial token-type ZSPI-DDL-Int2.
ZTMF-TKN-OldDmLoc token-type ZTMF-TYP-String.
ZTMF-TKN-NewDmLoc token-type ZTMF-TYP-String.
Tokens in Response Buffer
ZSPI-TKN-RetCode token-type ZSPI-TYP-Enum.
ZSPI-TKN-ErrList token-type ZSPI-TYP-List.
...
ZSPI-TKN-EndList token-type ZSPI-TYP-SSCTL.
ZTMF-TKN-DumpSerial token-type ZSPI-DDL-Int2.
ZTMF-TKN-OldDmLoc token-type ZSPI-TYP-String.
ZTMF-TKN-NewDmLoc token-type ZSPI-TYP-String.