TMF Management Programming Manual (H06.06+, J06.03+)
Table Of Contents
- HP NonStop TMF Management Programming Manual
- Legal Notices
- Contents
- What’s New in This Manual
- About This Manual
- 1 Introduction to TMF
- 2 Communicating With the TMFSERVE Process
- 3 SPI Programming Considerations for TMF
- 4 Common Definitions
- 5 Commands and Responses
- Command Summary
- Command Descriptions
- ABORT TRANSACTION
- ADD AUDITTRAIL
- ADD DATAVOLS
- ADD DUMPS
- ADD MEDIA
- ADD RESOURCEMANAGER
- ALTER AUDITDUMP
- ALTER AUDITTRAIL
- ALTER BEGINTRANS
- ALTER CATALOG
- ALTER DATAVOLS
- ALTER DUMPS
- ALTER MEDIA
- ALTER PROCESS
- ALTER TMF
- CANCEL OPERATION
- CLOSE RESOURCEMANAGER
- DELETE CATALOG
- DELETE DATAVOLS
- DELETE DUMPS
- DELETE MEDIA
- DELETE RESOURCEMANAGER
- DELETE TMF
- DELETE TRANSACTION
- DISABLE AUDITDUMP
- DISABLE BEGINTRANS
- DISABLE DATAVOLS
- DUMP FILES
- ENABLE AUDITDUMP
- ENABLE BEGINTRANS
- ENABLE DATAVOLS
- INFO ATDUMPDM
- INFO ATVOLUME
- INFO AUDITDUMP
- INFO AUDITTRAIL
- INFO BEGINTRANS
- INFO CATALOG
- INFO DATAVOLS
- INFO DUMPS
- INFO MEDIA
- INFO PROCESS
- INFO RESOURCEMANAGER
- INFO TMF
- LIST AUDITTRAIL
- NEXT AUDITTRAIL
- RECOVER FILES
- RELOCATE DISKDUMPS
- RESOLVE TRANSACTION
- START TMF
- STATUS ATFILE
- STATUS AUDITDUMP
- STATUS AUDITTRAIL
- STATUS BEGINTRANS
- STATUS CATALOG
- STATUS DATAVOLS
- STATUS OPERATION
- STATUS RESOURCEMANAGER
- STATUS RMTRANSBRANCHES
- STATUS TMF
- STATUS TMFSERVER
- STATUS TRANSACTION
- STATUS TRANSACTIONCHILDREN
- STOP TMF
- 6 Event Messages
- 7 Error and Warning Messages
- A TMF Configuration Limits and Defaults
- Index
Commands and Responses
HP NonStop TMF Management Programming Manual—540140-010
5-146
RELOCATE DISKDUMPS
ZTMF-TKN-NEWDMLOC
specifies the new system name and volume name of the disk media to be stored in
the TMF catalog. The system name is optional; if it is not included, the local system
name is used. This token is required; only one occurrence is allowed; a wild card
value is allowed.
Tokens in Response Buffer
ZSPI-TKN-RetCode
is the standard SPI return token described in the SPI Programming Manual.
ZSPI-TKN-ErrList
specifies the reason RELOCATE DISKDUMPS failed. The following errors can
appear in this field:
ZTMF-ERR-MustSpecifyDumpSerial
The command failed because no dump serial numbers were specified.
ZTMF-ERR-NoWildWithDumpSerial
The command failed because a wild card value was listed as well as specific
dump serial numbers.
ZTMF-ERR-MustSpecifyOldDmLoc
The command failed because no ZTMF-TKN-OldDmLoc token was supplied.
ZTMF-ERR-InvalidOldDmLoc
The command failed because the value in the ZTMF-TKN-OldDmLoc token
was not a valid volume name or wild card.
ZTMF-ERR-MustSpecifyNewDmLoc
The command failed because no ZTMF-TKN-NewDmLoc token was supplied.
ZTMF-ERR-InvalidNewDmLoc
The command failed because the value in the ZTMF-TKN-NewDmLoc token
was not a valid volume name or wild card.
ZTMF-ERR-NewDmLocNotWild
The command failed because a wild card character was specified for the
ZTMF-TKN-OldDmLoc token but not for the ZTMF-TKN-NewDmLoc token.