TMF Management Programming Manual (H06.06+, J06.03+)
Table Of Contents
- HP NonStop TMF Management Programming Manual
- Legal Notices
- Contents
- What’s New in This Manual
- About This Manual
- 1 Introduction to TMF
- 2 Communicating With the TMFSERVE Process
- 3 SPI Programming Considerations for TMF
- 4 Common Definitions
- 5 Commands and Responses
- Command Summary
- Command Descriptions
- ABORT TRANSACTION
- ADD AUDITTRAIL
- ADD DATAVOLS
- ADD DUMPS
- ADD MEDIA
- ADD RESOURCEMANAGER
- ALTER AUDITDUMP
- ALTER AUDITTRAIL
- ALTER BEGINTRANS
- ALTER CATALOG
- ALTER DATAVOLS
- ALTER DUMPS
- ALTER MEDIA
- ALTER PROCESS
- ALTER TMF
- CANCEL OPERATION
- CLOSE RESOURCEMANAGER
- DELETE CATALOG
- DELETE DATAVOLS
- DELETE DUMPS
- DELETE MEDIA
- DELETE RESOURCEMANAGER
- DELETE TMF
- DELETE TRANSACTION
- DISABLE AUDITDUMP
- DISABLE BEGINTRANS
- DISABLE DATAVOLS
- DUMP FILES
- ENABLE AUDITDUMP
- ENABLE BEGINTRANS
- ENABLE DATAVOLS
- INFO ATDUMPDM
- INFO ATVOLUME
- INFO AUDITDUMP
- INFO AUDITTRAIL
- INFO BEGINTRANS
- INFO CATALOG
- INFO DATAVOLS
- INFO DUMPS
- INFO MEDIA
- INFO PROCESS
- INFO RESOURCEMANAGER
- INFO TMF
- LIST AUDITTRAIL
- NEXT AUDITTRAIL
- RECOVER FILES
- RELOCATE DISKDUMPS
- RESOLVE TRANSACTION
- START TMF
- STATUS ATFILE
- STATUS AUDITDUMP
- STATUS AUDITTRAIL
- STATUS BEGINTRANS
- STATUS CATALOG
- STATUS DATAVOLS
- STATUS OPERATION
- STATUS RESOURCEMANAGER
- STATUS RMTRANSBRANCHES
- STATUS TMF
- STATUS TMFSERVER
- STATUS TRANSACTION
- STATUS TRANSACTIONCHILDREN
- STOP TMF
- 6 Event Messages
- 7 Error and Warning Messages
- A TMF Configuration Limits and Defaults
- Index
Commands and Responses
HP NonStop TMF Management Programming Manual—540140-010
5-147
RELOCATE DISKDUMPS
ZTMF-ERR-InvalidDumpSerial
The command failed because the value specified for DumpSerial was neither
the wild value nor a value higher than 63.
ZTMF-ERR-OnlyOneOldDmLoc
The command failed because there was more than one occurrence of the
ZTMF-TKN-OldDMLoc token in the input buffer.
ZTMF-ERR-OnlyOneNewDmLoc
The command failed because there was more than one occurrence of the
ZTMF-TKN-NewDmLoc token in the input buffer.
ZTMF-ERR-WarnNoDumpsRelocated
No dumps were relocated because, for example, a specified dump serial
number or the specified OldDmLoc does not exist.
ZTMF-TKN-DumpSerial
specifies the invalid dump serial number that caused the RELOCATE DISKDUMPS
command to fail.
ZTMF-TKN-OldDmLoc
specifies the invalid old disk media location that caused the RELOCATE
DISKDUMPS command to fail.
ZTMF-TKN-NewDmLoc
specifies the invalid new disk media location that caused the RELOCATE
DISKDUMPS command to fail.
Usage Guidelines
Only super-group users can issue this command. TMF must be started before you
issue the RELOCATE DISKDUMPS command.
If a wild card (*) is specified for ZTMF-TKN-OldDmLoc, a wild card must also be used
for ZTMF-TKN-NewDmLoc.
For more information on the RELOCATE DISKDUMPS command, see the TMF
Reference Manual.